77.140.30 承压钢 标准查询与下载



共找到 314 条与 承压钢 相关的标准,共 21

Standard Specification for Chromium and Chromium-Nickel Stainless Steel Plate, Sheet, and Strip for Pressure Vessels and for General Applications

ICS
77.140.30
CCS
发布
2020-07-15
实施

Standard Specification for Stainless Steel Bars and Shapes for Use in Boilers and Other Pressure Vessels

ICS
77.140.30
CCS
发布
2020-07-01
实施

1.1 This specification2 covers killed carbon-manganesesilicon steel plates intended for welded pressure vessels in service at moderate and lower temperatures. 1.2 The maximum thickness of plates is limited only by the capacity of the material to meet the specified mechanical property requirements. 1.3 For plates produced from coil and furnished without heat treatment or with stress relieving only, the additional requirements, including additional testing requirements and the reporting of additional test results, of Specification A20/A20M apply. 1.4 The values stated in either inch-pound units or SI units are to be regarded separately as standard. Within the text, the SI units are shown in brackets. The values stated in each system are not exact equivalents; therefore, each system must be used independently of the other. Combining values from the two systems may result in nonconformance with the specification. 1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Pressure Vessel Plates, Carbon Steel, High Strength, for Moderate and Lower Temperature Service

ICS
77.140.30
CCS
发布
2020-05-01
实施

1.1 This specification2 covers requirements for quenched and tempered carbon and alloy steel forgings for pressure vessel components. 1.2 All grades are considered weldable under proper conditions. Welding technique is of fundamental importance, and it is presupposed that welding procedure and inspection will be in accordance with approved methods for the grade of material used. NOTE 1—Grades 1 and 1A have different chemistries but the same mechanical requirements. NOTE 2—Designations have been changed as follows: Current Formerly Grade 1 Class 1 Grade 1A Class 1A Grade 1C Class 4 Grade 2 Class 1 Class 2 Grade 2 Class 2 Class 2A Grade 3 Class 1 Class 3 Grade 3 Class 2 Class 3A Grade 4N Class 1 Class 7 Grade 4N Class 2 Class 7A Grade 4N Class 3 Class 7B Grade 5 Class 1 Class 8 Grade 5 Class 2 Class 8A Grade 11 Class 4 Class 11C Grade 22 Class 3 Class 22B Grade 22 Class 4 Class 22C Grade 22 Class 5 Class 22D Grade 22V Class 22V Grade 3V Class 3V 1.3 The values stated in either inch-pound units or SI (metric) units are to be regarded separately as standard. Within the text and tables, the SI units are shown in brackets. The values stated in each system are not necessarily exact equivalents; therefore, to ensure conformance with the standard, each system shall be used independently of the other, and values from the two systems shall not be combined. 1.4 Unless the order specifies the applicable “M” specification designation, the material shall be furnished to the inchpound units. 1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Quenched and Tempered Carbon and Alloy Steel Forgings for Pressure Vessel Components

ICS
77.140.30
CCS
发布
2020-03-01
实施

Forged roll for cold rolling mill

ICS
77.140.30
CCS
发布
2019-12-13
实施

本标准规定了以不锈钢为覆材,碳素钢、低合金钢或不锈钢为基材,用爆炸焊接法或轧制复合法制造的复合板术语和定义,订货内容,型式、尺寸及重量,级别、标记,技术要求,试验方法,检验规则,包装、标志及质量证明书等。

Composite plates for pressure vessels Part 4: Copper-steel composite plates

ICS
77.140.30
CCS
H46
发布
2019-11-04
实施
2020-05-01

本标准规定了以不锈钢为覆材,碳素钢、低合金钢或不锈钢为基材,用爆炸焊接法或轧制复合法制造的复合板术语和定义,订货内容,型式、尺寸及重量,级别、标记,技术要求,试验方法,检验规则,包装、标志及质量证明书等。

Composite plates for pressure vessels Part 1: Stainless steel-steel composite plates

ICS
77.140.30
CCS
H46
发布
2019-11-04
实施
2020-05-01

本标准规定了以不锈钢为覆材,碳素钢、低合金钢或不锈钢为基材,用爆炸焊接法或轧制复合法制造的复合板术语和定义,订货内容,型式、尺寸及重量,级别、标记,技术要求,试验方法,检验规则,包装、标志及质量证明书等。

Composite plates for pressure vessels Part 2: Nickel-steel composite plates

ICS
77.140.30
CCS
H46
发布
2019-11-04
实施
2020-05-01

本标准规定了以不锈钢为覆材,碳素钢、低合金钢或不锈钢为基材,用爆炸焊接法或轧制复合法制造的复合板术语和定义,订货内容,型式、尺寸及重量,级别、标记,技术要求,试验方法,检验规则,包装、标志及质量证明书等。

Composite plates for pressure vessels Part 3: Titanium-steel composite plates

ICS
77.140.30
CCS
H46
发布
2019-11-04
实施
2020-05-01

Standard Specification for Stainless Steel Bars and Shapes for Use in Boilers and Other Pressure Vessels

ICS
77.140.30
CCS
发布
2019-09-01
实施

1.1 This specification2 covers hot-rolled carbon steel sheet for pressure vessels involving fusion welding or brazing. Welding and brazing technique is of fundamental importance and shall be in accordance with commercial practices. 1.2 The following grades are included in this specification: Mechanical Requirements Yield Strength, min Tensile Strength, min Grade ksi MPa ksi MPa A 25 170 45 310 B 30 205 50 345 C 33 230 55 380 D 35 240 60 415 E 38 260 65 450 F 42 290 70 485 G 45 310 75 515 H 45 310 75 515 1.3 Hot-rolled carbon steel sheet is generally furnished in cut lengths and to decimal thickness only. Coils may be furnished, provided tension test specimens are taken to represent the middle of the slab as required by 6.1.3. The purchaser should recognize this may require cutting the coils to obtain test samples and results in half-size coils. The sheet is furnished to the following size limits: Width, in. [mm] Thickness, in. [mm] Over 12 [Over 300] 0.270 to 0.230 [7.0 to 6.0] sheet (coils only) Under 0.230 to 0.057 [6.0 to 1.5] sheet 1.4 The values stated in either inch-pound units or SI units are to be regarded separately as standard. Within the text, the SI units are shown in brackets. The values stated in each system are not exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in nonconformance with the specification. 1.5 Tolerances are found in General Requirements Specifications A568/A568M and A635/A635M. The appropriate General Requirements specification is applied based on the thickness and width of the product ordered. 1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Steel, Sheet, Carbon, and High-Strength, Low-Alloy for Pressure Vessels

ICS
77.140.30
CCS
发布
2019-09-01
实施

Carbon steel plates for pressure vessels for low temperature service

ICS
77.140.30
CCS
发布
2019-06-04
实施

1.1 This specification2 covers heat-treated carbonmanganese-silicon steel plates intended for use in welded pressure vessels at moderate and lower temperature service. 1.2 Material under this specification is available in four strength levels, 75 ksi [515 MPa], 85 ksi [585 MPa], 80 ksi [550 MPa], and 90 ksi [620 MPa] minimum ultimate tensile strengths. 1.3 The maximum thickness of plates for Grades A, B, and C is limited only by the capacity of the chemical composition and heat treatment to meet the specified mechanical property requirements; however, current practice normally limits the maximum thickness of plates furnished under this specification to 6 in. [150 mm] for Grade A, 4 in. [100 mm] for Grade B, and 6 in. [150 mm] for Grade C. The maximum permitted nominal thickness is 1.5 in. [40 mm] for Grade D and 2 in. [50 mm] for Grade E. 1.4 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard. 1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Pressure Vessel Plates, Heat-Treated, Carbon-Manganese-Silicon Steel, for Moderate and Lower Temperature Service

ICS
77.140.30
CCS
发布
2019-05-01
实施

1.1 This specification2 covers two types of 21⁄4 Cr-1 Mo and three types of Cr-Mo-V alloy steel plates for use in the quenched-and-tempered condition, intended for the fabrication of welded pressure vessels and components. 1.2 Material under this specification is available in five types, designated “A,” “B,” “C,” “D,” and “E.” Type B is identical to Type A except for restrictive limits for carbon, phosphorus, sulfur, and nickel. The material is also available in five classes having the following strength levels. Type E is available only as Class 4 and 4a. Class Minimum Tensile Strength, ksi [MPa] 1 105 [725] 2 115 [795] 3 95 [655] 4 and 4a 85 [585] 1.3 The maximum thickness of plates is limited only by the capacity of the chemical composition to meet the specified mechanical property requirements. 1.4 The minimum thickness of plates is limited to 3⁄16 in. [5 mm]. 1.5 The material is intended to be suitable for fusion welding. Welding technique is of fundamental importance and it is presupposed that welding procedures will be in accordance with approved methods. 1.6 These alloy steel plates in the as-rolled condition are sensitive to cracking during flame cutting, transit, and handling. They should be shipped in the as-rolled condition only with the mutual agreement of the manufacturer and the purchaser or fabricator. 1.7 The values stated in either inch-pound units or SI units are to be regarded separately as standard. Within the text, the SI units are shown in brackets. The values stated in each system are not exact equivalents, therefore, each system must be used independently of the other. Combining values from the two systems may result in nonconformance with this specification. 1.8 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Pressure Vessel Plates, Alloy Steel, Quenched-and-Tempered, Chromium-Molybdenum, and Chromium-Molybdenum-Vanadium

ICS
77.140.30
CCS
发布
2019-05-01
实施

1.1 This specification establishes the requirements for welded, internally enhanced copper tube, in straight lengths or coils, suitable for use in refrigeration and air conditioning products or other heat exchangers. 1.2 Units—The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.3 The product shall be produced of the following coppers. Unless otherwise specified, tubes made from any one of these coppers may be supplied: Copper UNS No. Type of Metal C10200 Oxygen-free without residual deoxidants C12200 Phosphorized, high residual phosphorus (DHP) 1.4 The following pertains to the test method described in 18.5 of this specification. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory requirements prior to use. 1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Welded Copper Heat Exchanger Tubes With Internal Enhancement

ICS
77.140.30
CCS
发布
2019-04-01
实施

1.1 This specification covers requirements for low-carbon age-hardening nickel-copper-chromium-molybdenumcolumbium alloy steel forgings for pressure vessel components. 1.2 Forgings under this specification are available as Grades A or B. Grade A may be ordered in one or two classes as follows: 1.2.1 Grade A Class 1—Normalized-and-precipitation-heattreated, providing a minimum yield strength of 55 ksi [380 MPa] and a minimum tensile strength of 65 ksi [450 MPa]. 1.2.2 Grade A Class 2—Quenched-and-precipitation-heattreated, providing a minimum yield strength of 65 ksi [450 MPa] and a minimum tensile strength of 75 ksi [515 MPa]. 1.2.3 Grade A was the original steel composition in this specification. 1.3 Although the material is readily weldable, welding procedures are of fundamental importance and must be such as not to affect adversely the properties of the material, especially in the heat-affected zone. It is presupposed that welding procedures will be suitable for the material being welded. 1.4 Supplementary requirements, including those applicable in Specification A788/A788M, are provided for use when additional testing or inspection is desired. These shall apply only when specified individually by the purchaser in the order. 1.5 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system are not necessarily exact equivalents; therefore, to ensure conformance with the standard, each system shall be used independently of the other and values from the two systems shall not be combined. 1.6 This specification is expressed in both inch-pound and SI units. However, unless the order specifies the applicable “M” specification designation [SI units], the material shall be furnished to inch-pound units. 1.7 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Age-Hardening Alloy Steel Forgings for Pressure Vessel Components

ICS
77.140.30
CCS
发布
2019-03-01
实施

1.1 This specification2 covers chromium, chromium-nickel, and chromium-manganese-nickel stainless steel plate, sheet, and strip for pressure vessels and for general applications including architectural, building, construction, and aesthetic applications. 1.2 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard. 1.3 This specification is expressed in both inch-pound and SI units. However, unless the order specifies the applicable “M” specification designation (SI units), the material shall be furnished in inch-pound units. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Chromium and Chromium-Nickel Stainless Steel Plate, Sheet, and Strip for Pressure Vessels and for General Applications

ICS
77.140.30
CCS
/
发布
2019
实施
0000-00-00

Carbon steel and molybdenum alloy steel plate for boilers and other pressure vessels

ICS
77.140.30
CCS
发布
2018-12-11
实施

Carbon steel and molybdenum alloy steel plate for boilers and other pressure vessels

ICS
77.140.30
CCS
发布
2018-12-11
实施

1.1 This specification2 covers requirements for highstrength quenched and tempered alloy steel forgings for pressure vessels, isostatic presses, shock tubes, and similar components. 1.2 These materials are not intended for welded construction. 1.3 Three grades of nickel-chromium-molybdenum steels and six classes of increasing tensile strength are included. The strength class, section size, and configuration of the forging will largely dictate the applicable type(s) of steel. 1.4 The values stated in either inch-pound units or SI (metric) units are to be regarded separately as the standard. Within the text and tables, the SI units are shown in brackets. The values stated in each system are not exact equivalents; therefore, each system must be used independently of the other. Combining values from the two systems may result in nonconformance with the specification. 1.5 Unless the order specifies the applicable “M” specification designation, the material shall be furnished to the inchpound units. 1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Alloy Steel Forgings for High-Strength Pressure Component Application

ICS
77.140.30
CCS
发布
2018-11-01
实施



Copyright ©2007-2022 ANTPEDIA, All Rights Reserved
京ICP备07018254号 京公网安备1101085018 电信与信息服务业务经营许可证:京ICP证110310号