77.140.30 承压钢 标准查询与下载

ASTM A225/A225M-17 锰钒镍合金钢压力容器板的标准规格

1.1 This specification2 covers manganese-vanadium-nickel alloy steel plates intended primarily for welded layered pressure vessels. 1.2 Plates under this specification are available in two grades having different strength levels as follows: Grade   Tensile Strength, ksi [MPa] C   105–135 [725–930] D     8199;8199;8199;3 in. [75 mm] and under  80–105 [550–725] 8199;8199;8199;Over 3 in. [75 mm] 75–100 [515–690] 1.3 The maximum thickness of plates is limited only by the capacity of the chemical composition to meet the specified mechanical property requirements. 1.4 The values stated in either inch-pound units or SI units are to be regarded separately as standard. Within the text, the SI units are shown in brackets. The values stated in each system are not exact equivalents; therefore, each system must be used independently of the other. Combining values from the two systems may result in nonconformance with the specification. 1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Pressure Vessel Plates, Alloy Steel, Manganese-Vanadium-Nickel

DIN EN 10314:2016 高温下验证钢强度最小值导出法.德文版本EN 10314-2016

Method for the derivation of minimum values of proof strength of steel at elevated temperatures; German version EN 10314:2016

DIN EN 10213:2016 压力用钢铸件.德文版本EN 10213-2007+A1-2016

Steel castings for pressure purposes; German version EN 10213:2007+A1:2016

BS EN 10314:2016 钢在高温下屈服强度最小值的推导方法

Method for the derivation of minimum values of proof strength of steel at elevated temperatures

EN 10314:2016 高温下钢保证强度最小值的导出法

This European Standard specifies a method for deriving the minimum proof strength values for steels at elevated temperatures. However, this European Standard does not specify a verification procedure.

Method for the derivation of minimum values of proof strength of steel at elevated temperatures

EN 10213:2007+A1:2016 承压用铸钢件 包含修改件A1,2016

This European Standard applies to steel castings for pressure containing parts. It includes materials which are used for the manufacture of components, for pressure equipment. This European Standard relates to castings characterised by their chemical composition and mechanical properties. In cases where castings are joined by welding by the founder, this European Standard applies. In cases where castings are welded:- to wrought products (plates, tubes, forgings), or; - by non founders, this European Standard does not apply. NOTE For this harmonised supporting standard for materials, presumption of conformity to the Essential Requirements of the Directive is limited to technical data of the material in the standard and does not presume adequacy of the material to specific equipment. Consequently the technical data stated in the material standard should be assessed against the design requirements of the specific equipment to verify that the Essential Requirements of the Pressure Equipment Directive (PED) are satisfied.

Steel castings for pressure purposes

ASTM A240/A240M-16a 压力容器和通用应用的铬和铬镍不锈钢钢板, 片材以及带材的标准规格

1.1 This specification2 covers chromium, chromium-nickel, and chromium-manganese-nickel stainless steel plate, sheet, and strip for pressure vessels and for general applications including architectural, building, construction, and aesthetic applications. 1.2 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard. 1.3 This specification is expressed in both inch-pound and SI units. However, unless the order specifies the applicable “M” specification designation (SI units), the material shall be furnished in inch-pound units. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Specification for Chromium and Chromium-Nickel Stainless Steel Plate, Sheet, and Strip for Pressure Vessels and for General Applications

ASTM A1014/A1014M-16e1 高温服务用沉淀硬化螺栓(UNS N07718)的标准规格

1.1 This specification covers precipitation hardening bolting material (UNS N07718) and bolting components for high temperature service. See Specification A962/A962M for the definition of “bolting.” 1.2 The following referenced general requirements are indispensable for application of this specification: Specification A962/A962M. 1.3 Supplementary requirements are provided for use at the option of the purchaser. The supplementary requirements only apply when specified individually in the purchase order or contract. 1.4 This specification is expressed in both inch-pound and in SI units. However, unless the purchase order or contract specifies the applicable M designation (SI units), the inch-pound units shall apply. 1.5 The values stated in either SI units or inch-pound units are to be regarded separately as standard. Within the text, the SI units are shown in brackets. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard. 1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Precipitation-Hardening Bolting (UNS N07718) for High Temperature Service

ASTM A240/A240M-16 压力容器和通用应用的铬和铬镍不锈钢钢板, 片材以及带材的标准规格

1.1 This specification2 covers chromium, chromium-nickel, and chromium-manganese-nickel stainless steel plate, sheet, and strip for pressure vessels and for general applications including architectural, building, construction, and aesthetic applications. 1.2 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard. 1.3 This specification is expressed in both inch-pound and SI units. However, unless the order specifies the applicable “M” specification designation (SI units), the material shall be furnished in inch-pound units. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Specification for Chromium and Chromium-Nickel Stainless Steel Plate, Sheet, and Strip for Pressure Vessels and for General Applications

ASTM A1014/A1014M-16 高温服务用沉淀硬化螺栓 (UNS N07718) 的标准规格

1.1 This specification covers precipitation hardening bolting material (UNS N07718) and bolting components for high temperature service. See Specification A962/A962M for the definition of “bolting.” 1.2 The following referenced general requirements are indispensable for application of this specification: Specification A962/A962M. 1.3 Supplementary requirements are provided for use at the option of the purchaser. The supplementary requirements only apply when specified individually in the purchase order or contract. 1.4 This specification is expressed in both inch-pound and in SI units. However, unless the purchase order or contract specifies the applicable M designation (SI units), the inch-pound units shall apply. 1.5 The values stated in either SI units or inch-pound units are to be regarded separately as standard. Within the text, the SI units are shown in brackets. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard.

Standard Specification for Precipitation-Hardening Bolting (UNS N07718) for High Temperature Service

ASTM A479/A479M-16a 锅炉和其他压力容器用不锈钢棒材和型材的标准规格

1.1 This specification2 covers hot- and cold-finished bars of stainless steel, including rounds, squares, and hexagons, and hot-rolled or extruded shapes such as angles, tees, and channels for use in boiler and pressure vessel construction.2 Note 1: There are standards covering high nickel, chromium, austenitic corrosion, and heat-resisting alloy materials. These standards are under the jurisdiction of ASTM Subcommittee B02.07 and may be found in Annual Book of ASTM Standards, Vol 02.04. 1.2 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard. 1.3 Unless the order specifies the applicable “M” specification designation, the material shall be furnished to the inch-pound units.

Standard Specification for Stainless Steel Bars and Shapes for Use in Boilers and Other Pressure Vessels

ASTM A533/A533M-16 经回火和淬火的压力容器用锰钼和锰钼镍合金钢板的标准规格

1.1 This specification2 covers one type of manganese-molybdenum and four types of manganese-molybdenum-nickel alloy steel plates for use in the quenched and tempered condition for the construction of welded pressure vessels. 1.2 Material under this specification is available in five types, designated “A”, “B”, “C”, “D”, and “E”. The material is also available in three classes having the following strength levels. 8199;8199;Class Tensile Strength, ksi [MPa] 1 8201;80–100 [550 to 690] 2 8201;90–115 [620 to 795] 3 100–125 [690 to 860] 1.3 The maximum thickness of Class 1 and Class 2 plates is limited only by the capacity of the composition to meet the specified mechanical property requirements; however, current practice normally limits the maximum thickness to 12 in. [300 mm] for Types A through D and to 7 in. [180 mm] for Type E. 1.4 The maximum thickness of Class 3 plates is 21/2 in. [65 mm] for Types A through D and 2 in. [50 mm] for Type E. 1.5 The minimum nominal thickness of plates of all classes is 0.25 in. [6.5 mm]. 1.6 These alloy steel plates in the as-rolled condition are sensitive to cracking during transit and handling, particularly in thicknesses over about 1 or 2 in. [25 or 50 mm]. They should be shipped in the as-rolled conditions only by mutual agreement of manufacturer and the purchaser. 1.7 Plates covered by this specification are often used in the beltline region of nuclear reactor vessels where the material properties may be affected by high levels of radiation. Appendix X1 provides some information pertinent to this usage. 1.8 The values stated in either inch-pound units or SI units are to be regarded separately as stan......

Standard Specification for Pressure Vessel Plates, Alloy Steel, Quenched and Tempered, Manganese-Molybdenum and Manganese-Molybdenum-Nickel

ASTM A508/A508M-16 压力容器用淬火和回火真空处理的碳和合金钢锻件的标准规格

1.1 This specification2 covers quenched and tempered vacuum-treated carbon and alloy steel forgings for pressure vessels such as those used in reactor systems. Specifically, it covers forgings for vessel closures, shells, flanges, tube sheets, rings, heads, and similar parts. 1.2 All grades are considered weldable under proper conditions. Welding technique is of fundamental importance, and it is presupposed that welding procedure and inspection will be in accordance with approved methods for the grade of material used. 1.3 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard. 1.4 Unless the order specifies the applicable “M” specification designation, the material shall be furnished to the inch-pound units. Note 1: Grades 1 and 1A are composed of different chemistries but have the same mechanical requirements. Note 2: Designations have been changed as follows: 8199; Current Formerly Grade 1 Class 1 Grade 1A Class 1A Grade 2 Class 1 Class 2 Grade 2 Class 2 Class 2A Grade 3 Class 1 Class 3 Grade 3 Class 2 Class 3A Grade 4N Class 1 Cl......

Standard Specification for Quenched and Tempered Vacuum-Treated Carbon and Alloy Steel Forgings for Pressure Vessels

ASTM A479/A479M-16 锅炉及其它压力容器使用不锈钢棒材和型材的标准规格

1.1 This specification2 covers hot- and cold-finished bars of stainless steel, including rounds, squares, and hexagons, and hot-rolled or extruded shapes such as angles, tees, and channels for use in boiler and pressure vessel construction.2 Note 1: There are standards covering high nickel, chromium, austenitic corrosion, and heat-resisting alloy materials. These standards are under the jurisdiction of ASTM Subcommittee B02.07 and may be found in Annual Book of ASTM Standards, Vol 02.04. 1.2 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard. 1.3 Unless the order specifies the applicable “M” specification designation, the material shall be furnished to the inch-pound units.

Standard Specification for Stainless Steel Bars and Shapes for Use in Boilers and Other Pressure Vessels

KS D ISO 9329-2-2015 压力用无缝钢管 交货技术条件 第2部分：具有规定高温性能的非合金钢和合金钢

Seamless steel tubes for pressure purpose－Technical delivery Conditions－Part 2：Unalloyed and alloyed steels with specified elevated temperature properties

KS D ISO 9329-1-2015 压力用无缝钢管 交货技术条件 第1部分：具有规定室温性能的非合金钢

Seamless steel tubes for pressure purposes－Technical delivery conditions－ Part 1：Unalloyed steels with specified room temperature properties

KS D ISO 9329-1:2015 受压力的无缝钢管 交货技术条件 第1部分：规定室温性能的非合金钢

Seamless steel tubes for pressure purposes－Technical delivery conditions－ Part 1：Unalloyed steels with specified room temperature properties

KS D ISO 9329-2:2015 受压力的无缝钢管 交货技术条件 第2部分：规定高温性能的非合金钢和合金钢

Seamless steel tubes for pressure purpose－Technical delivery Conditions－Part 2：Unalloyed and alloyed steels with specified elevated temperature properties

ASTM A832/A832M-10(2015)e1 压力容器板 合金钢 铬钼钒的标准规范

1.1 This specification2 covers chromium-molybdenumvanadium alloy steel plates intended primarily for the fabrication of welded pressure vessels. 1.2 The plates furnished under this specification are required to be normalized-and-tempered. Specification A542/ A542M includes coverage of the material in the quenched-andtempered condition. 1.3 The maximum thickness of plates furnished to this specification is limited only by the capacity of the composition to meet the specified property requirements. However, the maximum thickness of plates normally furnished under this specification is 6 in. [150 mm]. 1.4 The material is intended to be suitable for fusion welding. Welding technique is of fundamental importance and it is presupposed that welding procedures will be in accordance with approved methods. 1.5 This specification is expressed in both inch-pound units and in SI units. However, unless the order specifies the applicable “M” specification designation (SI units), the material shall be furnished to inch-pound units. 1.6 The values stated in either inch-pound units or SI units are to be regarded separately as standard. Within the text, the SI units are shown in brackets. The values stated in each system must be used independently of the other. Combining values from the two systems may result in nonconformance with the specification.

Standard Specification for Pressure Vessel Plates, Alloy Steel, Chromium-Molybdenum-Vanadium

ASTM A479/A479M-15 锅炉及其它压力容器使用不锈钢棒材和型材的标准规格

1.1 This specification2 covers hot- and cold-finished bars of stainless steel, including rounds, squares, and hexagons, and hot-rolled or extruded shapes such as angles, tees, and channels for use in boiler and pressure vessel construction.2 Note 1: There are standards covering high nickel, chromium, austenitic corrosion, and heat-resisting alloy materials. These standards are under the jurisdiction of ASTM Subcommittee B02.07 and may be found in Annual Book of ASTM Standards, Vol 02.04. 1.2 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard. 1.3 Unless the order specifies the applicable “M” specification designation, the material shall be furnished to the inch-pound units.

Standard Specification for Stainless Steel Bars and Shapes for Use in Boilers and Other Pressure Vessels