77.140.30 承压钢 标准查询与下载

ASTM A240/A240M-15a 压力容器和一般用途使用铬和铬-镍不锈钢厚板, 薄板和带材的标准规格

1.1 This specification2 covers chromium, chromium-nickel, and chromium-manganese-nickel stainless steel plate, sheet, and strip for pressure vessels and for general applications including architectural, building, construction, and aesthetic applications. 1.2 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard. 1.3 This specification is expressed in both inch-pound and SI units. However, unless the order specifies the applicable “M” specification designation (SI units), the material shall be furnished in inch-pound units. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Specification for Chromium and Chromium-Nickel Stainless Steel Plate, Sheet, and Strip for Pressure Vessels and for General Applications

ASTM A240/A240M-15 压力容器和一般用途使用铬和铬-镍不锈钢厚板, 薄板和带材的标准规格

1.1 This specification2 covers chromium, chromium-nickel, and chromium-manganese-nickel stainless steel plate, sheet, and strip for pressure vessels and for general applications. 1.2 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard. 1.3 This specification is expressed in both inch-pound and SI units. However, unless the order specifies the applicable “M” specification designation (SI units), the material shall be furnished in inch-pound units. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Specification for Chromium and Chromium-Nickel Stainless Steel Plate, Sheet, and Strip for Pressure Vessels and for General Applications

ASTM A240/A240M-15b 压力容器和通用应用的铬和铬镍不锈钢钢板, 片材以及带材的标准规格

1.1 This specification2 covers chromium, chromium-nickel, and chromium-manganese-nickel stainless steel plate, sheet, and strip for pressure vessels and for general applications including architectural, building, construction, and aesthetic applications. 1.2 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard. 1.3 This specification is expressed in both inch-pound and SI units. However, unless the order specifies the applicable “M” specification designation (SI units), the material shall be furnished in inch-pound units. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Specification for Chromium and Chromium-Nickel Stainless Steel Plate, Sheet, and Strip for Pressure Vessels and for General Applications

ASTM A1014/A1014M-15 高温服务用沉淀硬化螺栓 (UNS N07718) 的标准规格

1.1 This specification covers precipitation hardening bolting material (UNS N07718) and bolting components for high temperature service. See Specification A962/A962M for the definition of “bolting.” 1.2 The following referenced general requirements are indispensable for application of this specification: Specification A962/A962M. 1.3 Supplementary requirements are provided for use at the option of the purchaser. The supplementary requirements only apply when specified individually in the purchase order or contract. 1.4 This specification is expressed in both inch-pound and in SI units. However, unless the purchase order or contract specifies the applicable M designation (SI units), the inch-pound units shall apply. 1.5 The values stated in either SI units or inch-pound units are to be regarded separately as standard. Within the text, the SI units are shown in brackets. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard.

Standard Specification for Precipitation-Hardening Bolting (UNS N07718) for High Temperature Service

KS D ISO 9328-3:2014 压力容器用钢板和带材 交货技术条件 第3部分：具有规定低温性能的镍合金钢

Steel plates and strips for pressure purposes－Technical delivery conditions－Part 3：Nickel-alloyed steels with specified low temperature properties

GSO ISO 9328-1:2014 压力用途扁钢产品 供货技术要求 第1部分：一般要求

This part of ISO 9328 specifies the general technical delivery conditions for steel flat products (plate/sheet and strip) used principally for the construction of pressure equipment. The general technical delivery requirements in ISO 404 also apply to products supplied in accordance with this part of ISO 9328

Steel flat products for pressure purposes – Technical delivery conditions - Part 1:General requirements

GSO ISO 9328-5:2014 压力用扁钢产品 供应技术要求 第5部分：细晶粒、机械热轧可焊钢

This part of ISO 9328 specifies the requirements for flat products for pressure equipment, made of thermomechanically rolled weldable fine grain steels as specified in Tables A.1 and B.1. The steels are not suitable for hot forming. Until now, no sufficient data for the standardization of the elevated temperature properties of these steels are available. If their use at such temperatures is intended, the conditions for this are specially agreed upon between the interested parties. The requirements and definitions of ISO 9328-1 also apply to this part of ISO 9328. NOTE 1 Fine grain steels are understood to be steels with a ferritic grain size of 6 or finer when tested in accordance with ISO 643. NOTE 2 This part of ISO 9328 offers the possibility of specifying products in accordance with European design codes and ASME-type design codes.

Steel flat products for pressure purposes – Technical delivery conditions – Part 5 : Weldable fine grain steels, thermomechanically rolled

GSO ISO 9328-4:2014 压力用途扁钢产品 技术供应要求 第4部分：镍合金钢和规定的低温性能

This part of ISO 9328 specifies the technical delivery conditions for plates and strip for pressure equipment made of nickel-alloy steels as specified in Tables A.1 and B.1. The requirements and definitions of ISO 9328-1 also apply to this part of ISO 9328. NOTE This part of ISO 9328 offers the possibility of specifying products in accordance with European design codes and ASME-type design codes.

Steel flat products for pressure purposes – Technical delivery conditions -- Part 4: Nickel-alloy steels with specified low temperature properties

GSO ISO 9328-3:2014 压力用途扁钢产品 供应技术要求 第3部分：细晶粒、刨削可焊钢

This part of ISO 9328 specifies the requirements for flat products for pressure equipment made of weldable fine grain steels as specified in Tables A.1 and B.1. The requirements and definitions of ISO 9328-1 also apply to this part of ISO 9328. NOTE 1 Fine grain steels are understood as steels with a ferritic grain size of 6 or finer when tested in accordance with ISO 643. NOTE 2 This part of ISO 9328 offers the possibility to specifying products in accordance with European design codes and ASME-type design codes.

Steel flat products for pressure purposes -- Technical delivery conditions -- Part 3: Weldable fine grain steels, normalized

GSO ISO 9328-2:2014 压力用途扁钢产品 供货技术要求 第2部分：具有规定高温性能的非合金钢和合金钢

This part of ISO 9328 specifies the technical delivery conditions for plates and strip for pressure equipment made of non-alloy and alloy steels as specified in Tables A.1 and B.1. The requirements and definitions of ISO 9328-1 also apply to this part of ISO 9328.

Steel flat products for pressure purposes -- Technical delivery conditions -- Part 2: Non-alloy and alloy steels with specified elevated temperature properties

JIS G 3120:2014 压力容器用淬火和回火的锰-钼及锰-钼-镍合金钢板

This Standard specifies quenched and tempered manganese-molybdenum and manganese-molybdenum-nickel alloy steel plates (hereafter referred to as "steel plates"),suited for thermal refining by quenching and tempering, to be used for nuclear reactors and other pressure vessels.

Manganese-molybdenum and manganese-molybdenum-nickel alloy steel plates quenched and tempered for pressure vessels

GSO ISO 9327-3:2013 钢锻造和轧制或冲压用棒材锻造 交货技术条件： 第3部分：具有低温凝固性能的镍钢

1.1 This part of ISO 9327 applies to forgings and rolled or forged bars in thicknesses up to 50 mm manufactured from the steels listed in Table 1 and to be delivered according to the specifications given in ISO 9327-1. 1.1 This part of ISO 9327 covers the following data: a) in Table 1 the limits for — the chemical composition according to the cast analysis; — the tensile properties at room temperature; — the indications on the usual heat treatment condition at the time of delivery; b) in Table 2 the permissible product analysis tolerances on the limiting values given for the cast analysis; c) in Table 3 the minimum impact energy values.

Steel forgings and rolled or forged bars for pressure purposes -- Technical delivery conditions -- Part 3: Nickel steels with specified low temperature properties

GSO ISO 9327-5:2013 通过锻造、轧制或压制成型棒材来成型的钢 交货技术条件 第5部分：耐腐蚀钢、不锈钢

1.1 This part of ISO 9327 applies to forgings and rolled or forged bars manufactured from the austenitic and austenitic-ferritics steels given in Table 1 and delivered according to the specifications given in ISO 9327-1. 1.2 This part of ISO 9327 covers the following data: a) In Table 1 the limits for — the chemical composition according to the cast analysis; — the tensile properties at room temperature; — the indications on the usual heat treatment condition at the time of delivery; b) in Table 2 the permissible deviations of the results of the product analysis from the specified limits for the cast analysis, c) in Table 3 the minimum elevated temperature proof strength values; d) in Table 4 the estimated average stress rupture properties.

Steel forgings and rolled or forged bars for pressure purposes -- Technical delivery conditions -- Part 5: Stainless steels

GSO ISO 9327-2:2013 通过锻造和轧制成型钢或通过锻造进行压制成型棒材 交货技术条件 第2部分：通过设定高温性能的合金和非合金钢（MO、Cr、CrMo）

1.1 This part of ISO 9327 applies to forgings and rolled or forged bars in thicknesses up to 250 mm (partly up to 500 mm) manufactured from the steels listed in Table 1 and to be delivered according to the specifications given in ISO 9327-1. 1.2 This part of ISO 9327 covers the following data: a) in Table 1 the limits for — the chemical composition according to the cast analysis; — the tensile properties at room temperature; — the impact properties; — the indications on the usual heat treatment condition at the time of delivery; b) in Table 2 the permissible product analysis tolerances on the limiting values given for the cast analysis; c) in Table 3 the minimum elevated temperature proof strength values (see C.4 of ISO 9327-1:1998); d) in Table 4 the estimated average stress rupture properties; e) in Table 5 the estimated average strength values for 1 % plastic strain.

Steel forgings and rolled or forged bars for pressure purposes -- Technical delivery conditions -- Part 2: Non-alloy and alloy (Mo, Cr and CrMo) steels with specified elevated temperature properties

GSO ISO 9327-1:2013 通过锻造和轧制成型钢或用于压制目的的锻造棒材 交货技术条件 第1部分：一般要求

1.1 This part of ISO 9327 covers the technical delivery conditions for forgings (see note 1) and for rolled or forged bars for pressure purposes manufactured from the following internationally used steels (see note 2): a) non-alloy and alloy ferritic or martensitic steels with specified room temperature properties and supplementary requirements for elevated temperature properties covered in ISO 9327-2; b) nickel steels with specified low temperature properties covered in ISO 9327-3; c) weldable fine grain steels with high proof strength (room temperature, elevated temperature and low temperature grades) covered in ISO 9327-4; d) austenitic and austenitic-ferritic steels (room temperature and elevated temperature grades) covered in ISO 9327-5. NOTE 1 In accordance with ISO 6929 the term forgings covers here open die forgings including ring rolled products as well as closed die forgings. NOTE 2 Additional to the internationally used steels for pressure purposes covered in parts 2 to 5 of ISO 9327, there are other steels used regionally or nationally for the same application. These other steels shall not be precluded by this International Standard provided that they comply with the relevant International or National Standards for vessel constructions. NOTE 3 The following International Standards also apply for steel products for pressure purposes: ISO 9328 parts 1 to 5, ISO 9329 parts 1 to 4, ISO 9330 parts 1 to 6, ISO 4978. 1.2 In special cases variations of the requirements of this International Standard or additions to them may form the subject of an agreement at the time of enquiry and order (see annex C). 1.3 In addition to the requirements of this International Standard the general technical delivery requirements in ISO 404 apply, unless otherwise indicated in the following.

Steel forgings and rolled or forged bars for pressure purposes -- Technical delivery conditions -- Part 1: General requirements

GSO ISO 9327-4:2013 钢锻造和轧制或冲压用棒材锻造 交货技术条件 第4部分：高强度可焊钢

1.1 This part of ISO 9327 applies to forgings and rolled or forged bars in thicknesses up to 250 mm manufactured from fine grain steels (see NOTE) given in Table 1 and to be delivered according to the specifications given in ISO 9327-1. The steels are classified into — room temperature grades (P…), — elevated temperature grades (PH…), — low temperature grades (PL…), — low and elevated temperature grades (PLH…). NOTE Fine grain steels are here understood as steels with grain size 6 or finer according to the grain size charts in ISO 643. 1.2 This part of ISO 9327 covers the following data: a) In Table 1 the limits for — the chemical composition according to the cast analysis; — the tensile properties at room temperature; — the indications on the usual heat treatment condition at the time of delivery; b) in Table 2 the permissible product analysis tolerances on the limiting values given for the cast analysis; c) in Table 3 the minimum impact energy values; d) in Table 4 the minimum elevated temperature proof strength values.

Steel forgings and rolled or forged bars for pressure purposes -- Technical delivery conditions -- Part 4: Weldable fine grain steels with high proof strength

KS D ISO 9327-1-2013 压力用钢锻件和轧制或锻造棒材 交货技术条件第 1 部分一般要求

Steel forgings and rolled or forged bars for pressure purposes - Technical delivery conditions Part 1 General requirements

KS D ISO 4978-2013 焊接气瓶用扁钢产品

Flat rolled steel products for welded gas cylinders

KS D ISO 9327-1:2013 压力用途的钢锻件和轧制或锻造的棒材 技术交货条件 第1部分：通用要求

Steel forgings and rolled or forged bars for pressure purposes - Technical delivery conditions Part 1 General requirements

KS D ISO 6303:2013 不包括ISO 2604 第1~6部分的压力容器钢 持久应力断裂特性的推导

Pressure vessel steels not included in ISO 2604, Part 1 to 6 - Derivation of long time stress rupture properties