77.140.30 承压钢 标准查询与下载

KS D ISO 2605-3:2013 压力容器钢制产品 高温特性的推导和验证 第3部分：在限定数据时、推导高温屈服应力或弹性极限应力特性可供选择的一种方法

Steel products for pressure purposes Derivation and verification of elevated temperature properties Part 3 An alternative procedure for deriving the elevated temperature yield or proof stress properties when data are limited

KS D ISO 9327-1:2013 压力用途的钢锻件和轧制或锻造的棒材 技术交货条件 第1部分：通用要求

Steel forgings and rolled or forged bars for pressure purposes - Technical delivery conditions Part 1 General requirements

ASTM A240/A240M-13c 用于压力容器的铬和铬镍不锈钢板 板和带的标准规范和一般应用

Standard Specification for Chromium and Chromium-Nickel Stainless Steel Plate, Sheet, and Strip for Pressure Vessels and for General Applications

ASTM A479/A479M-13b 锅炉和其他压力容器用不锈钢棒和形状的标准规范

Standard Specification for Stainless Steel Bars and Shapes for Use in Boilers and Other Pressure Vessels

GSO ISO 9328-7:2013 压力用途扁钢产品 供应技术要求 第7部分：不锈钢

This part of ISO 9328 specifies requirements for flat products for pressure purposes made of stainless steels, including austenitic creep-resisting steels, in thicknesses as indicated in Tables 7 to 10. Additionally the requirements of ISO 9328-1 also apply.

Steel flat products for pressure purposes -- Technical delivery conditions -- Part 7: Stainless steels

GSO ISO 9328-6:2013 压力用扁钢产品 供应技术要求 第6部分：细晶粒可焊钢 淬火和回火

This part of ISO 9328 specifies the requirements for flat products for pressure equipment made of quenched and tempered weldable fine grain steels as listed in Tables A.1 and B.1. The requirements and definitions in ISO 9328-1 also apply to this part of ISO 9328. NOTE 1 Fine grain steels are understood to be steels with a ferritic grain size of 6 or finer when tested in accordance with ISO 643. NOTE 2 This part of ISO 9328 offers the possibility of specifying products in accordance with European design codes and ASME-type design codes.

Steel flat products for pressure purposes -- Technical delivery conditions -- Part 6: Weldable fine grain steels, quenched and tempered

GSO ISO 4991:2013 压力用途铸钢件

This International Standard covers steel castings for parts subjected to pressure. It includes materials which are used for the manufacture of components subject to pressure vessel codes and components not subject to codes. This International Standard relates to castings manufactured from unalloyed and alloyed steel grades (characterized by their chemical composition, Table 1, and mechanical properties, Tables 2 to 5).

Steel castings for pressure purposes

GSO ISO 4978:2013 焊接气瓶用扁钢产品

Abstract Specifies the characteristics of flat rolled steel products with a thickness up to 6 mm of the unalloyed steels listed in table 1 which are intended for welded gas cylinders with a normalized structure. Describes for instance the manufacture of the steel, heat treatment, chemical composition, properties, surface condition, dimensions, acceptance tests, samples and test pieces.

Flat rolled steel products for welded gas cylinders

ASTM A736/A736M-12 低碳时效硬化镍铜铬钼铌合金钢压力容器板的标准规范

1.1 This specification2 covers low-carbon age-hardening alloy steel plates for welded pressure vessels and piping components. The specification covers nickel-copper-chromium-molybdenum-columbium steel. 1.2 Plates under this specification are available as follows: 1.2.1 Available in Grade A, Class 3 only. 1.2.1.1 Quenched and precipitation heat treated with a minimum specified tensile strength of 85 ksi for thinner plates and 75 and 70 ksi for thicker plates, with the minimum tensile strength dependent upon the plate thickness. The maximum thickness of Grade A, Class 3 plates is limited only by the capacity of the chemical composition and heat treatment to meet the specified mechanical property requirements; however, current practice usually limits the maximum thickness to 8 in. [200 mm]. 1.3 This specification is expressed in both inch-pound units and in SI units. However, unless the order specifies the applicable “M” specification designation (SI units), the material shall be furnished in inch-pound units. 1.4 The values stated in either inch-pound units or SI units are to be regarded separately as standard. Within the text, the SI units are shown in brackets. The values stated in each system are not exact equivalents. Therefore, each system must be used independently of the other. Combining values from the two systems may result in nonconformance with this specification.

Standard Specification for Pressure Vessel Plates, Low-Carbon Age-Hardening Nickel-Copper-Chromium-Molybdenum-Columbium Alloy Steel

ASTM A225/A225M-12 压力容器板 合金钢 锰钒镍标准规范

1.1 This specification covers manganese-vanadium-nickel alloy steel plates intended primarily for welded layered pressure vessels. 1.2 Plates under this specification are available in two grades having different strength levels as follows: Grade Tensile Strength, ksi [MPa] C105–135 [725–930] D 3 in. [75 mm] and under 80–105 [550–725] Over 3 in. [75 mm]75–100 [515–690] 1.3 The maximum thickness of plates is limited only by the capacity of the chemical composition to meet the specified mechanical property requirements; however, current mill practice normally limits Grade C to 0.58 in. [15 mm] maximum and Grade D to 6 in. [150 mm] maximum. 1.4 The values stated in either inch-pound units or SI units are to be regarded separately as standard. Within the text, the SI units are shown in brackets. The values stated in each system are not exact equivalents; therefore, each system must be used independently of the other. Combining values from the two systems may result in nonconformance with the specification.

Standard Specification for Pressure Vessel Plates, Alloy Steel, Manganese-Vanadium-Nickel

NB/T 20008.3-2012 压水堆核电厂用其他材料.第3部分：3级辅助系统泵、阀用铜 -铝合金铸件

本部分规定了压水堆核电厂辅助系统3级泵的叶轮以及各种阀件的铜-铝合金铸件的制造、化学成分、力学性能、无损检测等技术要求。 本部分规定了压水堆核电厂辅助系统3级泵的叶轮以及各种阀件的铜-铝合金铸件。

Other material for pressurized water reactor nuclear power plants.Part 3：Class 3 Copper-Aluminium alloy castings for anxiliary system pumps and valves

ASTM A612/A612M-12(2019) 中温和低温压力容器用高强度碳素钢板的标准规格

1.1 This specification2 covers killed carbon-manganese-silicon steel plates intended for welded pressure vessels in service at moderate and lower temperatures. 1.2 The maximum thickness of plates supplied under this specification is 1 in. [25 mm]. 1.3 For plates produced from coil and furnished without heat treatment or with stress relieving only, the additional requirements, including additional testing requirements and the reporting of additional test results, of Specification A20/A20M apply. 1.4 The values stated in either inch-pound units or SI units are to be regarded separately as standard. Within the text, the SI units are shown in brackets. The values stated in each system are not exact equivalents; therefore, each system must be used independently of the other. Combining values from the two systems may result in nonconformance with the specification. 1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Pressure Vessel Plates, Carbon Steel, High Strength, for Moderate and Lower Temperature Service

GOST R 55079-2012 钢铁. 电感耦合等离子体原子发射分析方法

Steel. Method of inductively coupled plasma atomic-emission analysis

GSO EN 10207:2011 简单压力容器用钢 板材、带材、棒材交货技术要求

This document specifies the technical delivery requirements for flat products and bars made of steel in accordance with the specifications for pressurized parts in simple pressure vessels as defined in the Directive 87/404/EEC (see Annex A) and standardized in EN 286-1 to -3.

Steels for simple pressure vessels - Technical delivery requirements for plates, strips and bars

ASTM A240/A240M-11a 一般用途用压力容器用铬不锈钢和铬-镍不锈钢厚钢板,薄钢板和带材的标准规格

1.1 This specification covers chromium, chromium-nickel, and chromium-manganese-nickel stainless steel plate, sheet, and strip for pressure vessels and for general applications. 1.2 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard. 1.3 This specification is expressed in both inch-pound and SI units. However, unless the order specifies the applicable “M” specification designation (SI units), the material shall be furnished in inch-pound units. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Specification for Chromium and Chromium-Nickel Stainless Steel Plate, Sheet, and Strip for Pressure Vessels and for General Applications

ASTM A240/A240M-11 一般用途用压力容器用铬不锈钢和铬-镍不锈钢厚钢板,薄钢板和带材的标准规格

1.1 This specification covers chromium, chromium-nickel, and chromium-manganese-nickel stainless steel plate, sheet, and strip for pressure vessels and for general applications. 1.2 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard. 1.3 This specification is expressed in both inch-pound and SI units. However, unless the order specifies the applicable “M” specification designation (SI units), the material shall be furnished in inch-pound units. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Specification for Chromium and Chromium-Nickel Stainless Steel Plate, Sheet, and Strip for Pressure Vessels and for General Applications

ASTM A387/A387M-11 压力容器用铬钼合金钢板的标准规格

1.1 This specification covers chromium-molybdenum alloy steel plates intended primarily for welded boilers and pressure vessels designed for elevated temperature service.

Standard Specification for Pressure Vessel Plates, Alloy Steel, Chromium-Molybdenum

ASTM A1017/A1017M-11(2015) 铬钼钨合金钢压力容器板的标准规格

1.1 This specification covers Chromium-Molybdenum-Tungsten alloy steel plates intended primarily for welded boilers and pressure vessels designed for elevated temperature service. 1.2 Plates are available under this specification in grades having different alloy contents as follows: Grade Nominal Chromium Content, % Nominal Molybdenum Content, % Nominal Tungsten Content, %         23 2.25 0.20 1.60 911 9.00 1.00 1.00 92 9.00 0.45 1.75 122 12.00 0.40 2.00 1.3 The maximum thickness of plates is limited only by the capacity of the composition to meet the specified mechanical property requirements. 1.4 The specification is expressed in both i......

Standard Specification for Pressure Vessel Plates, Alloy Steel, Chromium-Molybdenum-Tungsten

ASTM A1017/A1017M-11 铬钼钨合金钢制压力容器板标准规格

1.1 This specification covers Chromium-Molybdenum-Tungsten alloy steel plates intended primarily for welded boilers and pressure vessels designed for elevated temperature service. 1.2 Plates are available under this specification in grades having different alloy contents as follows:

Standard Specification for Pressure Vessel Plates, Alloy Steel, Chromium-Molybdenum-Tungsten

ASTM A541/A541M-05(2010) 压力容器部件用调质碳素钢和合金钢锻件的标准规范

Standard Specification for Quenched and Tempered Carbon and Alloy Steel Forgings for Pressure Vessel Components