77.140.65 钢丝、钢丝绳和环节链 标准查询与下载

DB13/T 5011-2019 钢丝（钢筋）焊接网通用技术要求

General technical requirements for steel wire (rebar) welded mesh

YB/T 5357-2019 钢丝镀锌层

本标准规定了圆形钢丝锌或锋-5%银或 10%%银合金镀层的技术要求，试验方法及检验规则。 本标准适用于各种用途的热浸镀电镀(锌或锌-5%%铝或 10%铝合金)钢丝镀层。

Steel wire galvanized layer

ASTM F552-14(2019) 与链式围栏有关的标准术语

Standard Terminology Relating to Chain Link Fencing

ASTM F2453/F2453M-14(2019) 6 in.²和#x2009网格用焊接钢丝网围栏织物（金属涂层或聚合物涂层）的标准规范[3871 mm²]或更小 在面板或卷中 具有均匀的网格

1.1 This specification covers welded wire mesh fence fabric produced from steel wire or metallic-coated steel wire. The metallic-coated fabric may be polymer coated after fabrication. 1.2 Welded wire mesh fence fabric is produced in four types, based on the kind of coating, as described in Section 4. 1.3 This specification is applicable to orders in either inch-pound units or SI units. Values stated in either inch-pound or SI units are to be regarded separately as the standard. Within the text, the SI units are shown in brackets. The values in the two systems are not exact equivalents; therefore, each system shall be used independent of the other, without combining values in any way. 1.4 This specification references notes and footnotes, which provide explanatory material. These notes and footnotes (excluding those in tables and figures) shall not be considered as requirements of this specification. 1.5 The following safety hazards caveat pertains only to the test methods portion, Section 13, of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations proper to use. 1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Welded Wire Mesh Fence Fabric (Metallic-Coated or Polymer Coated) for Meshes of 6 in.²  [3871 mm²] or Less, in Panels or Rolls, with Uniform Mes

ASTM B803/B803M-19 高强度锌的标准规范&x2013；5 ；%架空导线用铝-混合稀土合金涂层钢芯线

Standard Specification for High-Strength Zinc–5 % Aluminum-Mischmetal Alloy-Coated Steel Core Wire for Use in Overhead Electrical Conductors

ASTM B958/B958M-19 超高强度和超高强度A级锌的标准规范；架空导线用5%铝-混合稀土合金涂层钢芯线

Standard Specification for Extra-High-Strength and Ultra-High-Strength Class A Zinc–5% Aluminum-Mischmetal Alloy-Coated Steel Core Wire for Use in Overhead Electrical Conductors

ASTM B957/B957M-19 用于架空电导体的超高强度和超高强度镀锌（镀锌）钢芯线的标准规范

Standard Specification for Extra-High-Strength and Ultra-High-Strength Zinc-Coated (Galvanized) Steel Core Wire for Overhead Electrical Conductors

ASTM A1023/A1023M-19 通用碳素钢丝绳标准规范

Standard Specification for Carbon Steel Wire Ropes for General Purposes

ASTM A884/A884M-19e1 环氧涂层钢丝和焊丝加固标准规范

1.1 This specification covers plain and deformed steel wire and plain and deformed steel welded wire reinforcement with protective epoxy coating. A Class A minimum coating thickness is required for wire and welded wire reinforcement intended for use in concrete and masonry. A Class B minimum coating thickness is required for wire and welded wire reinforcement intended for use in mechanically stabilized earth applications. A Type 1 coating is a fusion-bonded epoxy coating that has been formulated to be sufficiently flexible to allow bending of the coated wire or welded wire reinforcement. A Type 2 coating is a fusion-bonded epoxy coating that has not been designed to be sufficiently flexible to allow bending of the coated wire or welded wire reinforcement. NOTE 1—The coating applicator is identified throughout this specification as the manufacturer. 1.2 This specification is applicable for orders in either inch-pound units (as Specification A884) or SI units [as Specification A884M]. 1.3 The values stated in either inch-pound or SI units are to be regarded separately as standard. Within the text, the SI units are shown in brackets. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other except as specifically noted in Table 1. Combining values from the two systems may result in non-conformance with this specification. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Epoxy-Coated Steel Wire and Welded Wire Reinforcement

ASTM A492-95(2019) 不锈钢钢丝绳标准规范

1.1 This specification covers the more commonly used types of round stainless steel wire intended especially for stranding into wire rope. 1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.3 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Stainless Steel Rope Wire

ASTM A884/A884M-19 环氧涂层钢丝和焊丝加固标准规范

Standard Specification for Epoxy-Coated Steel Wire and Welded Wire Reinforcement

ASTM A368-95a(2019) 不锈钢丝股标准规范

1.1 This specification covers stainless steel wire strand composed of a multiplicity of round wires and suitable for use as guy wires, overhead ground wires, and similar purposes. 1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.3 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Stainless Steel Wire Strand

MT/T 716-2019 煤矿重要用途钢丝绳验收技术条件

Technical conditions for acceptance of steel wire ropes for important uses in coal mines

ASTM A586-18 金属涂层平行和螺旋钢丝结构股标准规范

1.1 This specification covers metallic-coated steel wire structural strand, for use where a high-strength, high-modulus, multiple-wire tension member is desired as a component part of a structure. The strand is available with parallel or helical wire construction. 1.1.1 The strand is available with several metallic coating classes and with two strength grades, as described in Section 4. 1.2 The strand is furnished with Class A weight zinc or zinc-aluminum alloy-coated wires throughout. It can be furnished with Class B weight or Class C weight zinc-coated outer wires as an option. 1.3 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Metallic-Coated Parallel and Helical Steel Wire Structural Strand

YB/T 4682-2018 编织用铝包钢丝

Aluminum covered steel wire for braiding

YB/T 4165-2018 防振锤用钢绞线

Steel strand for anti-vibration hammer

YB/T 4222-2018 预绞式金具用镀层钢丝

Coated steel wire for pre-twisted fittings

YB/T 4683-2018 同步带用微细镀锌钢丝绳

Micro galvanized steel wire rope for timing belt

ASTM B910/B910M-07(2018) 退火铜包钢丝的标准规格

1.1 This specification covers bare round copper-clad steel for the following applications: electrical, electronic, grounding, telecommunications, and other applications. 1.2 Four conductivities are covered as follows: 21, 30, 40, and 70 %. 1.3 Temper is designated as annealed. 1.4 The values stated in inch-pound or SI units are to be regarded separately as the standard. Each system shall be used independently of the other. Combining values from the two systems may result in nonconformance with the specification. For conductor sizes designated by AWG, the requirements in SI units have been numerically converted from corresponding values stated or derived in inch-pound units. For conductor sizes designated by SI units only, the requirements are stated or derived in SI units. 1.5 The following precautionary statement pertains to the test method portion only, Section 7, of this specification: This standard does not purport to address all of the safety concerns, if any associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Annealed Copper-Clad Steel Wire

ASTM C933-18 焊接钢丝绳标准规范

1.1 This specification covers welded wire lath, flat or self-furring, with or without backing, designed for use as a base to receive portland cement-based interior plaster and exterior stucco. 1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.3 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Welded Wire Lath