77.140.65 钢丝、钢丝绳和环节链 标准查询与下载

ASTM A401/A401M-18 铬硅合金钢丝的标准规范

1.1 This specification covers round and shaped chromiumsilicon alloy steel spring wire having properties and quality intended for the manufacture of springs resistant to set when used at moderately elevated temperatures. This product is not meant to be used for non-static applications involving moderate fatigue stresses (see Specification A1000/A1000M) or high cycle fatigue applications (see Specification A877/A877M). This wire shall be provided either in the annealed and cold-drawn or quench and tempered condition as specified by the purchaser. 1.2 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard. 1.2.1 Within the text, the inch-pound units are shown in brackets. 1.3 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Steel Wire, Chromium-Silicon Alloy

ASTM A931-18 钢丝绳和绳股张力试验标准试验方法

1.1 This test method covers the tension testing of wire ropes and strand at room temperature, specifically to determine the measured breaking force, yield strength, elongation, and modulus of elasticity. Methods described in this standard are not intended for other purposes. 1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. Specific precautionary statements are given in Note 1 and Note

Standard Test Method for Tension Testing of Wire Ropes and Strand

ASTM A938-18 电线扭转试验的标准试验方法

1.1 This test method describes the torsion (or twist) testing of metallic wire. 1.2 The values stated in U.S. customary units are to be regarded as the standard. The SI equivalents of U.S. customary units may be approximate. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Method for Torsion Testing of Wire

ASTM F2919/F2919M-12(2018) 面板中具有可变网格图案或大于6 in.²[3871 mm²]网格的焊接钢丝网围栏织物（金属涂层或聚合物涂层）的标准规范

1.1 This specification covers welded wire mesh fence fabric produced from steel wire or metallic-coated steel wire. The metallic-coated fabric may be polymer coated after fabrication. 1.2 Welded wire mesh fence fabric is produced in four types, based on the kind of coating, as described in Section 4. 1.3 This specification is applicable to orders in either inch-pound units or SI units. Values stated in either inch-pound or SI units are to be regarded separately as the standard. Within the text, the SI units are shown in brackets. The values in the two systems are not exact equivalents; therefore, each system shall be used independent of the other, without combining values in any way. 1.4 This specification references notes and footnotes, which provide explanatory material. These notes and footnotes (excluding those in tables and figures) shall not be considered as requirements of this specification. 1.5 The following safety hazards caveat pertains only to the test methods portion, 13.4, of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Welded Wire Mesh Fence Fabric (Metallic-Coated or Polymer Coated) with Variable Mesh Patterns or Meshes Greater than 6 in.² [3871 mm²] in Panels

ASTM A510/A510M-18 钢丝和粗圆线 碳钢和合金钢的一般要求标准规范

Standard Specification for General Requirements for Wire Rods and Coarse Round Wire, Carbon Steel, and Alloy Steel

YB/T 4644-2018 测井电缆加强用镀锌钢丝

Galvanized steel wire for logging cable reinforcement

YB/T 4190-2018 工程用机编钢丝网及组合体

Machine-woven steel wire mesh and assembly for engineering use

YB/T 4643-2018 制绳用异形钢丝

Special-shaped steel wire for rope making

BS ISO 3108:2017 钢丝绳 试验方法 测定测得的断裂力

Steel wire ropes. Test method. Determination of measured breaking force

YB/T 4507-2017 钢丝绳索具拉力试验方法

Tensile test method for wire rope slings

YB/T 123-2017 铝包钢丝

Aluminum clad steel wire

DB44/T 2064-2017 环保型不锈钢光亮丝

本标准规定了环保型不锈钢光亮丝（以下简称光亮丝）的术语和定义、交货状态和代号﹑工艺要求、技术要求﹑试验方法﹑检验规则﹑包装﹑标志和质量证明书。 本标准适用于奥氏体型不锈钢光亮丝。

Environmentally friendly stainless steel bright wire

ISO 3108:2017 钢丝绳.测试方法.实测破断拉力的测定

This document specifies a method of tensile test to destruction for determining the actual breaking force of steel wire ropes as given in ISO 2408. It is also applicable for other ropes, unless the International Standard concerned specifically excludes its use, or gives another method.

Steel wire ropes - Test method - Determination of measured breaking force

YB/T 4615-2017 钢丝绳绳端 树脂套接

Steel wire rope end resin socket

YB/T 183-2017 稀土锌铝合金镀层钢绞线

Rare earth zinc aluminum alloy coated steel strand

YB/T 5218-2017 乐器用钢丝

musical instrument steel wire

YB/T 184-2017 钢芯铝绞线用稀土锌铝合金镀层钢丝

Rare earth zinc aluminum alloy coated steel wire for steel core aluminum stranded wire

YB/T 4612-2017 塑料管增强用碳素钢丝

Carbon steel wire for plastic pipe reinforcement

YB/T 4614-2017 钢丝用工字轮

I-shaped wheel for steel wire

YB/T 4616-2017 吊索具用安全护角 第1部分：钢丝绳护角

Safety corner guards for slings Part 1: Wire rope corner guards