77.140.80 钢铁铸件 标准查询与下载

BS ISO 19960:2015 有特殊物理性能的铸钢和合金

Cast steels and alloys with special physical properties

GSO ISO 9477:2015 一般工程和结构用高强度铸钢

1.1 This International Standard specifies requirements for four grades of heat-treated cast carbon and alloy steels for general engineering and structural purposes. 1.2 In cases where castings are produced by welding together component parts, this International Standard does not cover the welding process or the properties of the weldment. 1.3 The four steel grades are intended for service at ambient temperature. However, properties at other temperatures may be agreed on through the use of the supplementary requirements in 9.4.1 or 9.4.4 of ISO 4990:1986.

High strength cast steels for general engineering and structural purposes

ISO 19960:2015 特殊物理性能的铸钢及合金

This International Standard specifies cast steel and alloy grades with special physical properties. The cast steel and alloy grades covered by this International Standard are used in applications which require low linear thermal expansion, or low ferromagnetic responses, or low galling properties. NOTE Annex A gives information on ISO grade designation and available UNS numbers which are similar to the ISO grade designations.

Cast steels and alloys with special physical properties

ISO 4990:2015 铸钢件.交货的一般技术要求

This International Standard specifies the general technical delivery requirements for the Supply of steel nickel and cobalt alloy castings, including the requirements for the Selection and preparation of Samples and test pieces. When a material or product standard differ from this delivery specification, the material or product standard shall apply. In the case of investment castings, ISO 16468 will apply. This International Standard also specifies a_ group of supplementary reduirements which may be applied to steel nickel, and cobalt alloy castings. These redquirements are provided for use when additional testing or inspection is desired and apply only when individually specified by the purchaser

Steel castings - General technical delivery requirements

ISO 13583-1:2015 离心铸造钢及合金产品 第1部分:一般试验和公差

This part of ISO 13583 specifies the requirements for horizontal and vertical centrifugally cast steel and alloy products to be used in the following applications: a) heat resisting; c) general engineering. b) corrosion resisting;

Centrifugally cast steel and alloy products - Part 1: General testing and tolerances

ISO 9477:2015 一般工程和结构用高强度铸钢

This International Standard specifies requirements for four grades of heat treated cast carbon and alloy steels for general engineering and structural purposes. In cases where castings are produced by welding component parts together, this International Standard does not cover the welding process or the properties of the weldment. The four steel grades are intended for service at ambient temperature. However, properties at other temperatures can be agreed on through the use of supplementary requirements in ISO 4990.

High strength cast steels for general engineering and structural purposes

ISO 13583-2:2015 离心铸造钢及合金产品.第2部分:耐热材料

This part of ISO 13583 specifies cast steel and nickel alloy grades for elevated temperature service products manufactured by centrifugal casting.

Centrifugally cast steel and alloy products - Part 2: Heat-resistant materials

ASTM A703/A703M-15e1 钢铸件标准规范 压力容器的一般要求

Standard Specification for Steel Castings, General Requirements, for Pressure-Containing Parts

NF A32-054*NF EN 10293:2015 钢铸件.一般工程用钢铸件

La présente norme Européenne s'applique aux aciers moulés utilisés :- en mécanique générale. Leur utilisation inclut l'équipement (mécanique, électrique...), l'industrie automobile, le ferroviaire, l'armement, les équipements agricoles, l'industrie minière, etc.

Steel casting - Steel castings for general engineering uses

DIN EN 10293:2015 钢铸件.一般工程用钢铸件

Steel castings - Steel castings for general engineering uses; German version EN 10293:2015

T/CFA 02010204-4-2015 反击式破碎机 铸造板锤 技术条件

反击式破碎机铸造板锤的术语和定义、牌号、技术要求、试验方法、检验规则

Specifications for cast blow bars of impact crusher

T/CFA 02010204-2-2015 耐磨耐蚀铸铁件

耐磨耐蚀铸铁件的术语和定义、牌号、技术要求、试验方法、检验规则

Abrasion-corrosion resistant cast iron castings

BS EN 10293:2015 铸钢件 一般工程用铸钢件

Steel castings. Steel castings for general engineering uses

T/CFA 010201-1-2015 固溶强化铁素体球墨铸铁件

固溶强化铁素体球墨铸铁件的术语和定义、牌号、技术要求、取样和试验方法、检验规则

Solid solution strengthened ferritic spheroidal graphite iron castings

EN 10293:2015 钢铸件.一般工程用钢铸件

This European Standard applies to steel castings: for general engineering uses. Its uses include machinery (mechanical, electrical...), automotive industries, railroad, armament, agricultural equipment, mining, etc. In cases where castings are joined by welding by the founder, this document applies. In cases where castings are welded; - to wrought products (plates, tubes, forgings...), or; - by non-founders, this document does not apply.

Steel castings - Steel castings for general engineering uses

ASTM A148/A148M-15 建筑结构用高强度钢铸件的标准规格

1.1 This specification covers carbon steel, alloy steel, and martensitic stainless steel castings that are to be subjected to higher mechanical stresses than those covered in Specification A27/A27M. 1.2 Several grades of steel castings are covered, having the chemical composition and mechanical properties prescribed in Tables 1 and 2. 1.3 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard. 1.3.1 Within the text, the SI units are shown in brackets.

Standard Specification for Steel Castings, High Strength, for Structural Purposes

ASTM A439/A439M-15 奥氏体球墨铸铁件的标准规格

1.1 This specification covers austenitic ductile iron castings, which are used primarily for their resistance to heat, corrosion, and wear, and for other special purposes. 1.2 Austenitic ductile iron, also known as austenitic nodular iron or austenitic spheroidal iron, is characterized by having its graphite substantially in a spheroidal form and substantially free of flake graphite. It contains some carbides and sufficient alloy content to produce an austenitic structure. 1.3 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard.

Standard Specification for Austenitic Ductile Iron Castings

ASTM B883-15 金属注塑成型 (MIM) 材料的标准规格

1.1 This specification covers ferrous metal injection molded materials fabricated by mixing elemental or pre-alloyed metal powders with binders, injecting into a mold, debinding, and sintering, with or without subsequent heat treatment. 1.2 This specification covers the following injection molded materials. 1.2.1 Compositions:  1.2.1.1 MIM-2200, low-alloy steel 1.2.1.2 MIM-2700, low-alloy steel 1.2.1.3 MIM-4605, low-alloy steel 1.2.1.4 MIM-4140, low-alloy steel 1.2.1.5 MIM-316L, austenitic stainless steel 1.2.1.6 MIM-17-4 PH, precipitation hardening stainless steel 1.2.1.7 MIM-420, ferritic stainless steel 1.2.1.8 MIM-430L, ferritic stainless steel 1.2.1.9 MIM-Cu, copper 1.3 Chemical composition limits are specified in Table 1. (A) Excluding silver. 1.4 With the exception of the values for density and the mass used to determine density, for which the use of the gram per cubic centimetre (g/cm3) and gram (g) units is the longstanding industry practice, the values in inch-pound units are to be regarded as standard. The values given in parentheses or in separate tables are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Specification for Metal Injection Molded (MIM) Materials

ASTM A148/A148M-15a 结构用高强度钢铸件的标准规格

1.1 This specification covers carbon steel, alloy steel, and martensitic stainless steel castings that are to be subjected to higher mechanical stresses than those covered in Specification A27/A27M. 1.2 Several grades of steel castings are covered, having the chemical composition and mechanical properties prescribed in Tables 1 and 2. 1.3 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard. 1.3.1 Within the text, the SI units are shown in brackets.

Standard Specification for Steel Castings, High Strength, for Structural Purposes

ASTM A351/A351M-15 承压部件的奥氏体铸件的标准规格

1.1 This specification2 covers austenitic steel castings for valves, flanges, fittings, and other pressure-containing parts (Note 1). Note 1: Carbon steel castings for pressure-containing parts are covered by Specification A216/A216M, low-alloy steel castings by Specification A217/A217M, and duplex stainless steel castings by Specification A995/A995M. 1.2 A number of grades of austenitic steel castings are included in this specification. Since these grades possess varying degrees of suitability for service at high temperatures or in corrosive environments, it is the responsibility of the purchaser to determine which grade shall be furnished. Selection will depend on design and service conditions, mechanical properties, and high-temperature or corrosion-resistant characteristics, or both. 1.2.1 Because of thermal instability, Grades CE20N, CF3A, CF3MA, and CF8A are not recommended for service at temperatures above 800°F [425°C]. 1.3 Supplementary requirements of an optional nature are provided for use at the option of the purchaser. The Supplementary requirements shall apply only when specified individually by the purchaser in the purchase order or contract. 1.4 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard. 1.4.1 This specification is expressed in both inch-pound units and in SI units; however, unless the purchase order or contract specifies the applicable M specification designation (SI units), the inch-pound units shall apply. Within the text, the SI units are shown in brackets or parentheses.

Standard Specification for Castings, Austenitic, for Pressure-Containing Parts