77.150.30 (Copper products) 标准查询与下载

ASTM B505/B505M-14 铜合金连续铸件的标准规格

1.1 This specification establishes requirements for continuously cast rod, bar, tube, and shapes produced from copper alloys with nominal compositions as listed in Table 1.2 1.2 Castings produced to this specification may be manufactured for and supplied from stock. In such cases the manufacturer shall maintain heat traceability to specific manufacturing date and chemical analysis. 1.3 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Specification for Copper Alloy Continuous Castings

ASTM B30-14 锭形式铜合金的标准规范

1.1 This specification establishes the requirements for copper alloys in ingot form for remelting for the manufacturing of castings having the Copper Alloy UNS No. designation, commercial designations and nominal composition shown in Table 1 and Table 2. TABLE 1 Nominal Compositions Alloy Name Copper Alloy UNS No. Previously Used Designation Commercial Designation Nominal Composition, % Copper Tin Lead Zinc Ni- ckel Sul- fur Iron Alu- mi- num Man- ga- nese

Standard Specification for Copper Alloys in Ingot Form

ASTM B22/B22M-14 桥板和转盘用青铜铸件标准规格

1.1 This specification establishes requirements for bronze castings for turntables, movable bridges and bridge parts, and bronze castings suitable for use in bridges and other structures for fixed and expansion bearings in which motion is slow and intermittent. The following Copper Alloys are specified: UNS No. C86300, C90500, C91100, C91300, and C93700.Note 1—Historically, the alloys in this specification have been used in the applications listed in Appendix X1. Actual practice may vary.2 1.2 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Specification for Bronze Castings for Bridges and Turntables

ASTM B467-14 焊接铜镍管的标准规格

18.1 For purposes of determining compliance with the specified limits for requirements of the properties listed in the following table, and observed value or a calculated value shall be rounded as indicated in accordance with the rounding method of Practice E29. Property Rounded Unit for Observed or Calculated Value   Chemical composition nearest unit in the last right-hand place of figures of the specified limit Tensile strength Yield strength nearest ksi (nearest MPa up to 10 ksi, incl, nearest 5 MPa over 10 ksi) Elongation nearest 18201;% 1.1 This specification establishes the requirements for welded copper-nickel alloy pipe for general engineering purposes. The following alloys are covered:2 Copper Alloy UNS No.2 Type of Metal     C70600 90-10 copper-nickel C70620 90-10 copper-nickel   (Modified for Welding) C71500 70-30 copper-nickel C71520 70-30 copper-nickel   (Modified for Welding) 1.2 Units—The values sta......

Standard Specification for Welded Copper-Nickel Pipe

ASTM B411/B411M-14 铜镍硅合金杆材和棒材的标准规格

1.1 This specification establishes the requirements for copper-nickel-silicon alloy rod and bar produced from Copper Alloy UNS No. C64700 in straight lengths. 1.2 Units—The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard.

Standard Specification for Copper-Nickel-Silicon Alloy Rod and Bar

ASTM B806-14 通用铜合金永久铸模铸件的标准规格

1.1 This specification establishes requirements for copper alloy2 permanent mold castings for general applications. Nominal compositions of the alloys under this specification are shown in Table 1.TABLE 1 Nominal Composition Classification Copper Alloy UNS No. Nominal Composition Copper Aluminum Iron Manganese Nickel (incl Cobalt) Silicon Lead Zinc Tin Yellow brass C85470A 62.5

Standard Specification for Copper Alloy Permanent Mold Castings for General Applications

ASTM B763/B763M-14 阀门应用铜合金砂铸件标准规格

1.1 This specification establishes requirements for copper alloy sand castings for valve applications. Nominal compositions of the alloys defined by this specification are shown in Table 1.2 TABLE 1 Nominal Compositions Classification Copper Alloy UNS No. Commercial Designation Copper Tin Lead Zinc Nickel Iron Alumi- num Man- ganese Sili- con Bismuth Sele- nium Leaded red brass C83450  ......

Standard Specification for Copper Alloy Sand Castings for Valve Applications

ASTM B30-14a 铸锭铜合金的标准规格

1.1 This specification establishes the requirements for copper alloys in ingot form for remelting for the manufacturing of castings having the Copper Alloy UNS No. designation, commercial designations and nominal composition shown in Table 1 and Table 2. (A) Phosphorus 0.13.(B) Phosphorus 0.04.(C) Phosphorus 0.12.(D) Bismuth 5.0.(E) Selenium 0.5.(F) Selenium 0.9.(G) Selenium 0.20.(H) Selenium 0.03.(I) Phosphorus 0.1(J) Antimony 0.07, Boron 0.001. (A) When fine grained castings are specified, 0.02–0.12 titanium is added. 1.2 A cross reference of Copper Alloy UNS Nos. and copper alloy casting specifications is given in Table 3. 1.3 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.

Standard Specification for Copper Alloys in Ingot Form

ASTM B22-13 桥梁和转车台用青铜铸件的标准规格

1.1 This specification establishes requirements for bronze castings for turntables, movable bridges and bridge parts, and bronze castings suitable for use in bridges and other structures for fixed and expansion bearings in which motion is slow and intermittent. The following Copper Alloys are specified: UNS No. C86300, C90500, C91100, C91300, and C93700.Note 1—Historically, the alloys in this specification have been used in the applications listed in Appendix X1. Actual practice may vary.2 1.2 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Specification for Bronze Castings for Bridges and Turntables

ASTM B763-13 阀门用铜合金砂型铸件标准规格

1.1 This specification establishes requirements for copper alloy sand castings for valve applications. Nominal compositions of the alloys defined by this specification are shown in Table 1.2 TABLE 1 Nominal Compositions Classification Copper Alloy UNS No. Commercial Designation Copper Tin Lead Zinc Nickel Iron Alumi- 8199;num Man- ganese Sili- 8199;con Bismuth Selenium Leaded red brass

Standard Specification for Copper Alloy Sand Castings for Valve Applications

ASTM B950-13 铜和铜合金产品说明书编辑程序及形式的标准指南

4.1 The Form and Style for ASTM Standards manual provides mandatory requirements and recommended practices for the preparation and content of ASTM specifications. In order to promote consistency in the style and content of product specifications under its jurisdiction, Committee B05 recognizes the need to provide a supplementary document pertaining to the types of products and materials covered by specifications under its jurisdiction. 4.2 This guide contains a list of sections to be considered for inclusion in a specification for copper and copper alloys, recommended wording, or both, for such sections. An electronic template including committee adopted language is included in the Appendix.6 4.3 Persons drafting new product specifications, or modifying existing ones, under the jurisdiction of Committee B05, should follow this guide and the requirements of the Form and Style Manual to ensure consistency. 1.1 This guide covers the editorial procedures and form and style for product specifications under the jurisdiction of ASTM Committee B05 on Copper and Copper Alloys.Note 1—For standards other than product specifications, such as test methods, practices, and guides, see the appropriate sections of Form and Style for ASTM Standards (Blue Book).2 1.2 This guide has been prepared as a supplement to the current edition of the Form and Style Manual, and is appropriate for use by the subcommittees within ASTM Committee B05 on Copper and Copper Alloys. This guide is to be applied in conjunction with the Form and Style Manual. The Appendix contains a copy of the B05 electronic template which includes adopted language for various sections and provides a template for drafting B05 product specifications.Note 2—The contents of this guide were previously maintained as a white paper under the title, “ASTM Committee B05 Outline of Form of Specifications.” 1.3 Subcommittees preparing new product specifications or revising existing ones should follow the practices and procedures outlined herein, and be guided by the latest specifications covering similar commodities. 1.4 If a conflict exists between this guide and the mandatory sections of the current edition of the Form and Style Manual, the Form and Style Manual requirements have precedence. If a conflict exists between this guide and the nonmandatory sections of the current edition of the Form and Style Manual, the guide has precedence. 1.5 When patents are involved, the specifications writer should refer to the Form and Style Manual section on patents and trademarks. Also, refer to part F of the Form and Style Manual for trademark information and the safety hazards caveat.

Standard Guide for Editorial Procedures and Form of Product Specifications for Copper and Copper Alloys

ASTM B301/B301M-13 易切削铜条材、棒材、线材和型材的标准规格

1.1 This specification establishes the requirements for free-cutting copper rod, bar, wire, and shapes of UNS Alloy Nos. C14500, C14510, C14520, C14700, and C18700, suitable for high-speed screw machine work or for general applications. 1.2 Typically, product made to this specification is furnished as straight lengths. Sizes 1/2 in. [12 mm] and under may be furnished in coils when requested. 1.3 Units—The values stated in either SI units or inch-pound units are to be regarded separately as standard. Within the text, SI units are shown in brackets. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard.

Standard Specification for Free-Cutting Copper Rod, Bar, Wire, and Shapes

ASTM B763/B763M-13e1 阀门应用铜合金砂铸件标准规格

1.1 This specification establishes requirements for copper alloy sand castings for valve applications. Nominal compositions of the alloys defined by this specification are shown in Table 1.2 TABLE 1 Nominal Compositions Classification Copper Alloy UNS No. Commercial Designation Copper Tin Lead Zinc Nickel Iron Alumi- 8199;num Man- ganese Sili- 8199;con Bismuth Sele- nium Leaded red brass C83450

Standard Specification for Copper Alloy Sand Castings for Valve Applications

ASTM B22/B22M-13e1 桥板和转盘用青铜铸件标准规格

1.1 This specification establishes requirements for bronze castings for turntables, movable bridges and bridge parts, and bronze castings suitable for use in bridges and other structures for fixed and expansion bearings in which motion is slow and intermittent. The following Copper Alloys are specified: UNS No. C86300, C90500, C91100, C91300, and C93700.Note 1—Historically, the alloys in this specification have been used in the applications listed in Appendix X1. Actual practice may vary.2 1.2 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Specification for Bronze Castings for Bridges and Turntables

ASTM B2-13 中度冷拉铜线标准规格

1.1 This specification covers medium-hard-drawn round copper wire for electrical purposes (see Explanatory Note 1). 1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.2.1 Exception—For density, resistivity and temperature, the values stated in SI units are to be regarded as standard. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Specification for Medium-Hard-Drawn Copper Wire

ASTM B98/B98M-13 铜硅合金杆材、棒材和型材标准规格

1.1 This specification establishes requirements for copper-silicon rod, bar, and shapes for UNS Copper Alloys C65100, C65500, and C66100.Note 1—Material for hot forging is covered by Specification B124/B124M.Note 2—For ASME Boiler and Pressure Vessel Code applications, see Specification SB-98 in Section II of that code. 1.2 Units—The values stated in either SI units or inch-pound units are to be regarded separately as standard. Within the text, SI units are shown in brackets. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard.

Standard Specification for Copper-Silicon Alloy Rod, Bar and Shapes

ASTM B584-13 通用铜合金砂型铸件标准规格

1.1 This specification covers requirements for copper alloy sand castings for general applications. Nominal compositions of the alloys defined by this specification are shown in Table 1.2 This is a composite specification replacing former documents as shown in Table 1. TABLE 1 Nominal Compositions   Classification Copper Alloy UNS No. Previous Designation Commercial Designation Copper Tin Lead Zinc Nickel Iron Alum- inum Man- ganese Sili- con

Standard Specification for Copper Alloy Sand Castings for General Applications

ASTM B130-13 弹头壳用商用青铜带材的标准规格

17.1 For purposes of determining compliance with the specified property limits for the properties listed in the following table, an observed value of a calculated value shall be rounded as indicated in accordance with the rounding method of Practice E29: Property Rounded Unit for Observed or Calculated Value     Chemical composition Hardness nearest unit in the last right-hand significant digit used in expressing the limiting value. Tensile strength 8199;nearest ksi (5 MPa) Grain size:   8199;Up to 0.055 mm, incl 8199;nearest multiple of 0.005 mm 8199;Over 0.055 to 0.160 mm, incl 8199;nearest 0.01 mm Elongation:   8199;58201;% and over 8199;nearest 18201;% 1.1 This specification establishes the requirements for commercial bronze strip for manufacture of bullet jacket cups and ammunition components from Copper Alloy UNS No. C22000.2 1.2 Units–The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.

Standard Specification for Commercial Bronze Strip for Bullet Jackets

ASTM B250/B250M-13 锻造铜合金丝通用要求的标准规格

12.1 For the purpose of determining compliance with the specified limits for requirements of the properties listed in the following table, an observed value or calculated value shall be rounded as indicated in accordance with the rounding method of Practice E29. Property Rounded Unit for Observed or Calculated Value     8199;8199;Dimensions 8199;8199;Chemical composition 8199;8199;Hardness 8199;8199;Electrical resistivity/conductivity 8199;8199;nearest unit in the last 8199;8199;8199;right-hand significant 8199;8199;8199;digit used in expressing 8199;8199;8199;the limiting value   8199;8199;Tensile strength 8199;8199;Yield strength 8199;8199;nearest ksi [5 MPa] 8199;8199;   8199;8199;Elongation   8199;8199;8199;Below 58201;% 8199;8199;nearest multiple of 0.58201;% 8199;8199;8199;58201;% and over 8199;8199;nearest 18201;%   8199;8199;Grain size   8199;8199;8199;Under 0.060 mm 8199;8199;nearest multiple of 0.005 mm 8199;8199;8199;0.060 mm and over 8199;8199;nearest 0.01 mm 1.1 This specification establishes requirements common to wrought copper and copper alloy wire and shall apply to Specifications B16/B16M,

Standard Specification for General Requirements for Wrought Copper Alloy Wire

ASTM B3-13 软或炼铜线标准规格

1.1 This specification covers drawn and annealed or soft round bare copper wire for electrical purposes (see Explanatory Note 1). 1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.2.1 Exception—For density, resistivity and temperature, the values stated in SI units are to be regarded as standard. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Specification for Soft or Annealed Copper Wire