77.150.30 (Copper products) 标准查询与下载

ASTM B981/B981M-12 低铅黄铜条、棒材和型材标准规格

1.1 This specification establishes the requirements for low leaded brass rod, bar, wire, and shapes of any specified cross section produced from Copper Alloys UNS No. C36300, C36500, C37000, C37100 and C37700 suitable for high-speed screw machining applications. Note 18212;Refer to Specification B124/B124M when purchasing bar or rod for forging production. 1.2 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Specification for Low Leaded Brass Rod, Bar and Shapes

ASTM B643-12 铍铜合金无缝管标准规格

1.1 This specification establishes requirements for copper-beryllium alloy seamless tube in straight lengths. Copper Alloy UNS C17200 will be the alloy furnished whenever Specification B643 is specified. 1.2 Units8212;The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.3 The following safety hazard caveat pertains only to the test methods described in this specification. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Specification for Copper-Beryllium Alloy Seamless Tube

ASTM B967/B967M-12a 铜-锌-锡-铋合金条材、棒材及线材的标准规格

1.1 This specification establishes the requirements for copper-zinc-tin-bismuth alloy rod, bar and wire of alloy UNS Nos. C49250, C49255, C49260, C49300, C49340, C49350, C49355, and C49360 intended for use in plumbing applications and drinking water systems. 1.2 Typically, rod and bar product made to this specification is furnished as straight lengths. Wire (H04) 0.08-0.3 in. [2-8 mm inclusive] is furnished in coil form, and H50 shapes. 1.3 Units???The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard. 1.4 The following safety hazard caveat pertains only to the test method(s) described in this specification. 1.4.1 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Specification for Copper-Zinc-Tin-Bismuth Alloy Rod, Bar and Wire

ASTM B129-12 弹药筒黄铜弹壳帽壳标准规格

For the purposes of determining compliance with the specified limits for requirements of the properties listed in the following table, an observed value or a calculated value shall be rounded as indicated in accordance with the rounding method of Practice E29. Property Rounded Unit for Observed or Calculated Value Chemical compositionnearest unit in the last righthand signif- icant digit used in expressing the limiting value Grain size: Up to 0.055 mm, inclnearest multiple of 0.005 mm Over 0.055 to 0.160 mm, inclnearest 0.01 mm1.1 This specification establishes the requirements for annealed cartridge brass cups produced of Copper Alloy UNS No. C26000 for processing into cartridge cases of the following types: 1.1.1 Type I, for small arms cartridge case cups, and 1.1.2 Type II, for artillery cartridge case cups. 1.2 Units8212;Values stated in inch-pound units are to be regarded as standard, except for grain size, which is given in SI units. The values given in parentheses are mathematical conversions to SI units, which are provided for information only and are not considered standard.

Standard Specification for Cartridge Brass Cartridge Case Cups

ASTM B101-12 建筑结构用包铅铜薄板材和带材标准规格

1.1 This specification establishes the requirements for lead-coated copper sheet and strip in flat lengths (or in coils) in ounce-weight thicknesses for roofing, flashing, gutters, downspouts, and for the general sheet metalwork in building construction. The lead coating is applied by hot dipping. 1.2 Products produced to this specification are not intended for electrical applications. 1.3 Units8212;Values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units, which are provided for information only and are not considered standard. Note 18212;A companion specification for copper sheet and strip for building construction is Specification B370. 1.4 The following hazard caveat pertains to the test method portion, Section 17, of this specification. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Specification for Lead-Coated Copper Sheet and Strip for Building Construction

ASTM B171/B171M-12 压力容器、冷凝器和热交换器用铜合金板材及片材的标准规格

1.1 This specification2 establishes the requirements for copper-alloy plate, sheet, and circles cut from plate and sheet for pressure vessels, condensers, and heat exchangers. The following alloys are covered: Copper Alloy Previously Used Designation C36500 Leaded Muntz Metal C44300 Admirality, Arsenical C44400 Admirality, Antimonial C44500 Admirality, Phosphorized C46400 Naval Brass, Uninhibited C46500 Naval Brass, Arsenical C61300 Aluminum Bronze C61400 Aluminum Bronze D C63000 108201;% Aluminum-Nickel Bronze C63200 98201;% Aluminum-Nickel Bronze C70600 90-10 Copper Nickel C70620 90-10 Copper Nickel -(modified for welding) C71500 70-30 Copper Nickel C71520 70-30 Copper Nickel-(modified for welding) ......

Standard Specification for Copper-Alloy Plate and Sheet for Pressure Vessels, Condensers, and Heat Exchangers

ASTM B601-12 锻造及铸造铜和铜合金回火名称与符号的标准分类

1.1 This classification establishes temper designations for copper and copper alloys???wrought and cast. The temper designations are classified by the process or processes used in manufacturing the product involved and its resulting properties. It is not a specification of copper and copper alloys. 1.2 The property requirements for the tempers are given in the applicable product specification.

Standard Classification for Temper Designations for Copper and Copper Alloysmdash;Wrought and Cast

ASTM B250/B250M-12 锻造铜合金丝一般要求的标准规格

1.1 Thi......

Standard Specification for General Requirements for Wrought Copper Alloy Wire

ASTM B272-12 带精制(轧制或拉制)边缘(扁丝或带)的扁铜制品标准规格

1.1 This specification establishes the requirements for copper products, flat wire and strip, with rolled or drawn finished edges produced for general application. 1.1.1 The product is produced in UNS Copper Nos. C10100, C10200, C10300, C10500, C10700, C10800, C11000, C11040, C12200, and C14200 unless otherwise established by agreement between manufacturer and purchaser. 1.2 Units???Values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units, which are provided for information only and are not considered standard.Note 1???When a copper other than that listed in 1.1.1 is designated by the purchaser, the resulting product shall conform to the physical, mechanical, performance, dimensional, and tolerance requirements per agreement between the manufacturer and purchaser.

Standard Specification for Copper Flat Products with Finished (Rolled or Drawn) Edges (Flat Wire and Strip)

ASTM B552-12 水淡化厂用无缝和焊接铜-镍管标准规格

1.1 This specification establishes requirements for seamless and welded copper-nickel tubes from 0.250 to 2.125 in. (6.35 to 54.0 mm) in diameter for use in heat exchangers in water desalting plants. The following alloys are involved: Copper or Copper Alloy UNS No. Type of Metal C70600 90-10 copper-nickel C70620 90-10 copper-nickel (Modified for Welding) C71500 70-30 copper-nickel C71520 70-30 copper-nickel (Modified for Welding)

Standard Specification for Seamless and Welded Copperndash;Nickel Tubes for Water Desalting Plants

ASTM B587-12 黄铜焊接管标准规格

1.1 This specification establishes the requirements for round, rectangular, and square copper alloy welded tube for general engineering applications. 1.2 Units???Values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units, which are provided for information only and are not considered standard. 1.3 The following hazard statement pertains only to the test method described in 18.2.3, 18.2.4, 18.2.6, and 18.2.7 of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Specification for Welded Brass Tube

ASTM B2-12 中等硬度冷拉铜丝标准规格

1.1 This specification covers medium-hard-drawn round copper wire for electrical purposes (see Explanatory Note 1). 1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.2.1 Exception???The SI values of density and resistivity are to be regarded as standard. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Specification for Medium-Hard-Drawn Copper Wire

ASTM B370-12 建筑结构用铜片材和带材的标准规格

1.1 This specification establishes the requirements for rolled copper sheet and strip in flat lengths or coils in ounce-weight thicknesses for roofing, flashing, gutters, downspouts, and general sheet metal work in building construction. 1.1.1 Products produced to this specification are not intended for electrical applications. 1.2 Units???The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.Note 1???Specification B101 is an associated specification for lead-coated copper sheets and strip for building construction. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Specification for Copper Sheet and Strip for Building Construction

ASTM B298-12 镀银的软或退火铜线用标准规格

1.1 This specification covers silver-coated, soft or annealed, round copper wire, intended for use in electrical equipment, as follows: 1.1.1 Class A???Wire whose silver coating is at least 1.258201;% of the total weight of the coated wire. 1.1.2 Class B???Wire whose silver coating is at least 2.508201;% of the total weight of the coated wire. 1.1.3 Class C???Wire whose silver coating is at least 4.008201;% of the total weight of the coated wire. 1.1.4 Class D???Wire whose silver coating is at least 6.108201;% of the total weight of the coated wire. 1.1.5 Class E???Wire whose silver coating is at least 10.008201;% of the total weight of the coated wire. 1.2 Silver-coated wire having different minimum percentages of silver by weight may be obtained by mutual agreement between the manufacturer and the purchaser. For information purposes the thickness of coating in microinches provided by the percentages listed above is shown in Table 1 (Explanatory Note 1).TABLE 1 Tensile Requirements Diameter, in. Area at 20??C Elongation in 10 in., min,8201;% Thickness of Coating, ??in. (For Information Only) cmils in.2 Class A, 1.25 % Silver

Standard Specification for Silver-Coated Soft or Annealed Copper Wire

ASTM B131-12 铜合金弹头火帽壳标准规格

For the purposes of determining compliance with the specified limits for requirements of the properties listed in the following table, an observed value, or a calculated value, shall be rounded as indicated in accordance with the rounding method of Practice E29. PropertyRounded Unit for Observed or Calculated Value Chemical compositionNearest unit in the last right-hand significant digit used in expressing the limiting value Grain sizeNearest multiple of 0.005 mm1.1 This specification establishes the requirements for bullet jacket preform cups produced of Copper Alloy UNS No. C22000 for processing into bullet jackets of the following types and classes: 1.1.1 Type I8212;Caliber 0.30. 1.1.2 Type II8212;Caliber 0.45. 1.1.3 Type III8212;Caliber 0.50. 1.1.4 Type IV8212;As specified in the contract or order. 1.1.5 Class I8212;Not annealed. 1.1.6 Class II8212;Annealed. 1.2 Units8212;Values stated in inch-pound units are to be regarded as standard, except for grain size, which is given in SI units. The values in parentheses are mathematical conversions to SI units, which are provided for information only and are not considered standard.

Standard Specification for Copper Alloy Bullet Jacket Cups

ASTM B3-12 软或退火铜线标准规格

1.1 This specification covers drawn and annealed or soft round bare copper wire for electrical purposes (see Explanatory Note 1). 1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.2.1 Exception???For density, resistivity and temperature, the values stated in SI units are to be regarded as standard.

Standard Specification for Soft or Annealed Copper Wire

ASTM B372-12 无缝铜及铜合金矩形波导管标准规格

For purposes of determining compliance with the specified limits for requirements of chemical composition, hardness, and electrical resistivity, an observed value or a calculated value shall be rounded to the nearest unit in the last right-hand place of the figures of the specified limit in accordance with the rounding method of Practice E29.1.1 This specification establishes the requirements for seamless copper and copper-alloy rectangular tube intended for use as transmission lines in electronic equipment. Five types of material are specified having the following nominal compositions: Copper or Copper Alloy UNS No. Previously Used DesignationNominal Composition, % Copper ZincPhos- phorus C10100 Copper, Type OFEA99.99B...... C10200Copper, Type OFA99.95B...... C10300Copper, Type OFXLPA99.95B...0.003 C12000Copper, Type DLPA99.90B...0.008 C22000Commercial bronze, 90 %9010... ______________ A Types OF, OFE, OFXLP, and DLP are described in Classification B224. B Minimum copper percentage. 1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units which are provided for information only and are not considered standard.

Standard Specification for Seamless Copper and Copper-Alloy Rectangular Waveguide Tube

ASTM B122/B122M-11 铜镍锡合金,铜镍锌合金(镍银),铜镍合金中厚板,薄板,条板及轧制棒材的标准规格

1.1 This specification establishes the requirements for copper-nickel-tin alloy, copper-nickel-zinc alloy (nickel silver), and copper-nickel alloy plate, sheet, strip, and rolled bar. The following alloys are covered: Previously Copper AlloyUsed Nominal Composition, UNS No. Designation% Copper Nickel Zinc TinChro- mium C70600...9010 ......... C70620...8610......... C7100068020 ......... C7150057030 ......... C71520...6531......... C72200...8515 ......0.5 C72500...89 9 ...2... C7350017218 10...... C7400097010 20............

Standard Specification for Copper-Nickel-Tin Alloy, Copper-Nickel-Zinc Alloy (Nickel Silver), and Copper-Nickel Alloy Plate, Sheet, Strip, and Rolled Bar

ASTM B453/B453M-11 铜锌铅合金(铅黄铜)条材,棒材及型材的标准规格

1.1 This specification establishes the requirements for copper-zinc-lead alloy (leaded-brass) rod, bar, wire, and shapes produced from Copper Alloys UNS Nos. C33500, C34000, C34500, C35000, C35300, C35330, C35350, and C35600. These alloys have nominal composition given in Table 1. 1.1.1 This product is suitable for applications requiring extensive machining before such cold-forming operations as swaging, flaring, severe knurling, or thread rolling. Note 18212;Refer to Appendix X1 for additional applications information. 1.1.2 Typically, product made to this specification is furnished as straight lengths. Sizes ½ in. [12 mm] and under may be furnished as wire in coils or on reels when requested. 1.2 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard. Note 28212;Refer to Specifications B16/B16M

Standard Specification for Copper-Zinc-Lead Alloy (Leaded-Brass) Rod, Bar, and Shapes

ASTM B967/B967M-11a 铜锌锡铋合金条材,棒材及线材标准规格

1.1 This specification establishes the requirements for copper-zinc-tin-bismuth alloy rod, bar and wire of alloy UNS Nos. C49255, C49260, C49300, C49340, C49350, and C49360 intended for use in plumbing applications and drinking water systems. 1.2 Typically, rod and bar product made to this specification is furnished as straight lengths. Wire (H04) 0.08-0.3 in. [2-8 mm inclusive] is furnished in coil form, and H50 shapes. 1.3 Units8212;The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard. 1.4 The following safety hazard caveat pertains only to the test method(s) described in this specification. 1.4.1 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Specification for Copper-Zinc-Tin-Bismuth Alloy Rod, Bar and Wire