77.150.30 (Copper products) 标准查询与下载

ASTM B950-11a 铜和铜合金产品的说明书编辑程序及形式的标准指南

The Form and Style for ASTM Standards manual provides mandatory requirements and recommended practices for the preparation and content of ASTM specifications. In order to promote consistency in the style and content of product specifications under its jurisdiction, Committee B05 recognizes the need to provide a supplementary document pertaining to the types of products and materials covered by specifications under its jurisdiction. This guide contains a list of sections to be considered for inclusion in a specification for copper and copper alloys, recommended wording, or both, for such sections. An electronic template including committee adopted language is included in the Appendix. Persons drafting new product specifications, or modifying existing ones, under the jurisdiction of Committee B05, should follow this guide and the requirements of the Form and Style Manual to ensure consistency.1.1 This guide covers the editorial procedures and form and style for product specifications under the jurisdiction of ASTM Committee B05 on Copper and Copper Alloys. Note 18212;For standards other than product specifications, such as test methods, practices, and guides, see the appropriate sections of Form and Style for ASTM Standards (Blue Book). 1.2 This guide has been prepared as a supplement to the current edition of the Form and Style Manual, and is appropriate for use by the subcommittees within ASTM Committee B05 on Copper and Copper Alloys. This guide is to be applied in conjunction with the Form and Style Manual. The Appendix contains a copy of the B05 electronic template which includes adopted language for various sections and provides a template for drafting B05 product specifications. Note 28212;The contents of this guide were previously maintained as a white paper under the title, “ASTM Committee B05 Outline of Form of Specifications.” 1.3 Subcommittees preparing new product specifications or revising existing ones should follow the practices and procedures outlined herein, and be guided by the latest specifications covering similar commodities. 1.4 If a conflict exists between this guide and the mandatory sections of the current edition of the Form and Style Manual, the Form and Style Manual requirements have precedence. If a conflict exists between this guide and the nonmandatory sections of the current edition of the Form and Style Manual, the guide has precedence. 1.5 When patents are involved, the specifications writer should refer to the Form and Style Manual section on patents and trademarks. Also, refer to part F of the Form and Style Manual for trademark information and the safety hazards caveat.

Standard Guide for Editorial Procedures and Form of Product Specifications for Copper and Copper Alloys

ASTM B944-11 铜铍焊接热交换器和冷凝器管(UNS C17510号)的标准规格

1.1 This specification establishes the requirements for copper-beryllium alloy UNS No. C17510 welded tube in straight lengths. 1.2 Units8212;The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units, which are provided for information only and are not considered standard. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Specification for Copper-Beryllium Welded Heat Exchanger and Condenser Tube (UNS No. C17510)

ASTM B592-11 铜锌铝钴合金及铜锌锡铁合金中厚板,薄板,条板及轧制棒材的标准规格

1.1 This specification covers the requirements for plate, sheet, strip, and rolled bar in alloys C66300 and C68800. Note 18212;Since alloy C68800 is frequently used in a variety of applications where yield strength and stress-corrosion resistance may be critical, it is recommended that drawings or samples of the part to be fabricated and details of application be submitted for use in establishing temper and treatment of material. Note 28212;Alloy C66300 is covered by a patent. Interested parties are invited to submit information regarding the identification of an alternative(s) to this patented item to the ASTM International Headquarters. Your comments will receive careful consideration at a meeting of the responsible technical committee, which you may attend. 1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.

Standard Specification for Copper-Zinc-Aluminum-Cobalt Alloy, Copper-Zinc-Tin-Iron Alloy Plate, Sheet, Strip, and Rolled Bar

ASTM B121/B121M-11 铅黄铜中厚板,薄板,条板及轧制棒材的标准规格

1.1 This specification establishes the requirements for copper-zinc-lead alloys (leaded brass) plate, sheet, strip, and rolled bar. The following alloys are covered:1.2 The values stated in either inch-pound units or SI units are to be regarded separately as standard. Within the text, the SI units are shown in brackets. The values stated in each system are not exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in nonconformance with the specification.

Standard Specification for Leaded Brass Plate, Sheet, Strip, and Rolled Bar

ASTM B271/B271M-11e1 铜基合金离心铸件标准规格

1.1 This specification establishes requirements for centrifugal castings of copper-base alloys having the nominal compositions shown in Table 1.TABLE 1 Nominal Compositions Classification Copper Alloy UNS No. Commercial Designation Copper Tin Lead Zinc Nickel Iron Alum- inum Mang- anese Silicon Leaded red brass C83600 85-5-5-5 85  5  5  5

Standard Specification for Copper-Base Alloy Centrifugal Castings

ASTM B608-11 焊接铜铝管的标准规格

For purposes of determining compliance with the specified limits for requirements of the properties listed in the following table, an observed value or a calculated value shall be rounded as indicated in accordance with the rounding method of Practice E29. PropertyRounded Unit for Observed or Calculated Value Chemical compositionnearest unit in the last right-hand significant digit used in expressing the limiting value Tensile strengthnearest ksi (5 MPa)1.1 This specification establishes the requirements for arc-welded pipe for use in brackish water or seawater piping systems. 1.2 Units8212;The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.3 The following hazard statement pertains only to the test method described in 8.2 and 14.3.2 of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Specification for Welded Copper-Alloy Pipe

ASTM B967/B967M-11a 铜锌锡铋合金条材,棒材及线材标准规格

1.1 This specification establishes the requirements for copper-zinc-tin-bismuth alloy rod, bar and wire of alloy UNS Nos. C49255, C49260, C49300, C49340, C49350, and C49360 intended for use in plumbing applications and drinking water systems. 1.2 Typically, rod and bar product made to this specification is furnished as straight lengths. Wire (H04) 0.08-0.3 in. [2-8 mm inclusive] is furnished in coil form, and H50 shapes. 1.3 Units8212;The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard. 1.4 The following safety hazard caveat pertains only to the test method(s) described in this specification. 1.4.1 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Specification for Copper-Zinc-Tin-Bismuth Alloy Rod, Bar and Wire

ASTM B30-11 铜合金铸锭标准规格

1.1 This specification establishes the requirements for copper alloys in ingot form for remelting for the manufacturing of castings having the Copper Alloy UNS No. designation, commercial designations and nominal composition shown in Table 1 and Table 2. 1.2 A cross reference of Copper Alloy UNS Nos. and copper alloy casting specifications is given in Table 3. 1.3 The values stated in inch-pound units are to be regarded as standard. No other units of measurement are included in this standard.

Standard Specification for Copper Alloys in Ingot Form

ASTM B824-11 铜合金铸件一般要求的标准规范

For the purpose of determining compliance with the specified limits for requirements of the properties listed in the following table, an observed value or a calculated value shall be rounded as indicated in accordance with the rounding method of Practice E29.1.1 This specification establishes general requirements common to ASTM copper alloy casting specifications B22, B61, B62, B66, B67, B148, B176, B271, B369, B427, B505/B505M, B584, B763, B770, and B806. These requirements apply to the casting specifications to the extent referenced therein. 1.1.1 In the event of conflict between this specification and a casting specification, the requirements of the casting specification shall take precedence. 1.2 The chemical composition and other requirements not included in this specification shall be prescribed in the casting product specifications. 1.3 Units8212;The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.4 No precise quantitative relationship can be stated between the properties of the metal in various locations of the same casting or between the properties of castings and those of a test bar casting from the same metal. (See Appendix X1.)

Standard Specification for General Requirements for Copper Alloy Castings

ASTM B5-11 高电导率韧炼铜精炼型材标准规格

Calculated values shall be rounded to the specified number of places in accordance with Practice E29. 1.1 This specification establishes the requirements for high conductivity, tough-pitch, copper wire bars, cakes, slabs, billets, ingots, and ingot bars.

Standard Specification for High Conductivity Tough-Pitch Copper Refinery Shapes

ASTM B75/B75M-11 无缝铜管的标准规范

1.1 This specification establishes the requirements for seamless round, rectangular, and square copper tube suitable for general engineering applications. 1.1.1 Tubes made from any of the following Copper UNS No. designations shall be supplied unless otherwise specified in the contract or purchase order: Copper UNS No.Type of Copper C10100Oxygen-free electronic C10200Oxygen-free without residual deoxidants C10300Oxygen-free, extra low phosphorus C10800Oxygen-free, low phosphorus C12000Phosphorus deoxidized, low residual phosphorus C12200Phosphorus deoxidized, high residual phosphorus 1.2 Units8212;The values stated in either inch-pound units or SI units are to be regarded separately as standard. Within the text, SI units are shown in brackets. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard. 1.3 The following hazard statement pertains only to the test methods described in Sections 20.5.2.1, 21.2.9, and 21.2.10 of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Specification for Seamless Copper Tube

ASTM B505/B505M-11 铜合金连续铸件的标准规格

1.1 This specification establishes requirements for continuously cast rod, bar, tube, and shapes produced from copper alloys with nominal compositions as listed in Table 1. 1.2 Castings produced to this specification may be manufactured for and supplied from stock. In such cases the manufacturer shall maintain heat traceability to specific manufacturing date and chemical analysis. 1.3 The values stated in either SI units or inch/pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Specification for Copper Alloy Continuous Castings

ASTM B453/B453M-11e1 铜-锌-铅合金(含铅青铜)杆材,棒材和型材标准规格

1.1 This specification establishes the requirements for copper-zinc-lead alloy (leaded-brass) rod, bar, wire, and shapes produced from Copper Alloys UNS Nos. C33500, C34000, C34500, C35000, C35300, C35330, C35350, and C35600. These alloys have nominal composition given in Table 1.TABLE 1 Nominal Composition, % Copper Alloy UNS No. Copper Zinc Lead C33500 63.5 36.0 0.5 C34000 63.5 35.3 1.2 C34500 63.5 34.5 2.0 C35000 61.5 37.1 1.4 C35300 61.5 36.5 2.0 C35330 61.8 35.7

Standard Specification for Copper-Zinc-Lead Alloy 40;Leaded-Brass41; Rod, Bar, and Shapes

ASTM B370-11 房屋建筑用铜薄板和带材标准规格

1.1 This specification establishes the requirements for rolled copper sheet and strip in flat lengths or coils in ounce-weight thicknesses for roofing, flashing, gutters, downspouts, and general sheet metal work in building construction. 1.1.1 Products produced to this specification are not intended for electrical applications. 1.2 Units8212;The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. Note 18212;Specification B101 is an associated specification for lead-coated copper sheets and strip for building construction. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Specification for Copper Sheet and Strip for Building Construction

ASTM B370-11e1 建筑结构用包铅铜薄板和带材的标准规格

1.1 This specification establishes the requirements for rolled copper sheet and strip in flat lengths or coils in ounce-weight thicknesses for roofing, flashing, gutters, downspouts, and general sheet metal work in building construction. 1.1.1 Products produced to this specification are not intended for electrical applications. 1.2 Units8212;The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. Note 18212;Specification B101 is an associated specification for lead-coated copper sheets and strip for building construction. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Specification for Copper Sheet and Strip for Building Construction

ASTM B159/B159M-11 磷青铜线的标准规格

1.1 This specification establishes the requirements for round, square and flat phosphor bronze wire of UNS Alloy Nos. C51000, C52100, and C52400 for general and spring applications.1.1.1 Rectangular and square wire of the three alloys are generally available in sizes up to a maximum of 0.188 in. [5 mm] thick and 1.250 in. [32 mm] wide.1.1.2 Round wire from Copper Alloy UNS No. C51000 is generally available in sizes up to 0.500 in. [13 mm] in diameter.1.2 The values stated in either inch-pound units or in SI units are to be regarded separately as standard. Within the text, the SI units are shown in brackets. The values stated in each system are not exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in nonconformance with the specification.1.3 Additional requirements for these products are established in Specification B 250/B 250M, see Section .This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.Note 1It is to be understood that this specification is general. Since the product is used for many applications where the requirements of the operations used are too particular to be specified by any of the ordinary mechanical tests, it is frequently advisable to submit samples or drawings to the manufacturer and secure an adjustment of temper to suit the actual application for which the product is intended.Note 2Product in rod, bar and shape form is produced to Specification B 139/B 139M.

Standard Specification for Phosphor Bronze Wire

ASTM B16/B16M-10(2015) 用于螺丝机的自由切割黄铜棒 棒和形状的标准规格

1.1 This specification establishes the requirements for free-cutting brass rod, bar, wire, and shapes of any specified cross section produced from Copper Alloy UNS Nos. C36000 or C36010 suitable for high-speed screw machining applications and moderate thread rolling. 1.2 Units—Values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard. 1.2.1 Within the text, SI units are shown in brackets. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Specification for Free-Cutting Brass Rod, Bar and Shapes for Use in Screw Machines

ASTM B770-10 通用铜铍合金砂型铸件标准规范

1.1 This specification establishes requirements for copper-beryllium alloy sand castings for general applications and nominal compositions alloys defined by this specification are shown in Table 1. 1.2 Units8212;The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.3 The following safety hazard caveat pertains only to the test methods described in this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory requirements prior to use.

Standard Specification for Copper-Beryllium Alloy Sand Castings for General Applications

ASTM B968/B968M-10 铜及铜合金管和管道压扁试验的标准试验方法

When properly performed and interpreted, the flattening test will provide information about the relative ductility of a tube and presence of surface defects. For welded tube products, the test will provide information on the integrity of the weld seam. In certain product specifications which establish requirements for tubes of sizes greater than 4 in. [100 mm], the test may be allowed as a substitute to the expansion pin test in B153.1.1 This test method establishes the requirements for the flattening test for copper and copper alloy pipe and tube of all sizes. The method addresses both inch-pound and metric considerations, and both seamless and welded product. 1.2 Units8212;Values stated in either inch-pound units or SI units are to be regarded as standard. Within the text, SI units are shown in brackets. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Test Method for Flattening of Copper and Copper-Alloy Pipe and Tube

ASTM B30-10 铜基合金铸锭标准规范

1.1 This specification establishes the requirements for copper alloys in ingot form for remelting for the manufacturing of castings having the Copper Alloy UNS No. designation, commercial designations and nominal composition shown in Table 1 and Table 2. 1.2 A cross reference of Copper Alloy UNS Nos. and copper alloy casting specifications is given in Table 3. 1.3 The values stated in inch-pound units are to be regarded as standard. No other units of measurement are included in this standard.

Standard Specification for Copper Alloys in Ingot Form