77.150.30 (Copper products) 标准查询与下载

ASTM B505/B505M-10 铜合金连续铸件标准规范

1.1 This specification establishes requirements for continuously cast rod, bar, tube, and shapes produced from copper alloys with nominal compositions as listed in Table 1. 1.2 Castings produced to this specification may be manufactured for and supplied from stock. In such cases the manufacturer shall maintain heat traceability to specific manufacturing date and chemical analysis. 1.3 The values stated in either SI units or inch/pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Specification for Copper Alloy Continuous Castings

ASTM B754-10(2015)e1 铜及铜合金带材平面偏差的测量和记录的测试方法

5.1 This test method is intended for measuring distortion in strip used for making close tolerance parts. Since distortion in this strip would influence the shape of the part being produced and cause difficulties in feeding through close-fitting dies and other manufacturing equipment, it is important that this material be flat. 5.2 This test method provides a universal procedure for measuring the irregularities that cause the deviation from flatness. 5.3 This test method allows the purchaser and manufacturer to inspect strip with a standard technique to a mutually agreed upon and acceptable percentage deviation from flatness. 1.1 This test method establishes a procedure for the measurement of distortions in thin metal strip and the application of these measurements to an equation that will indicate the deviation from flatness. 1.2 The distortions to be measured in this test method are dish, wavy edges, buckle, longitudinal corrugation, and herringbone. 1.3 This test method is not intended to include the measurement of coil set or longitudinal curl, camber or edgewise curvature, or twist. 1.4 This test method is limited to metal strip 0.003 to 0.020 in. (0.08 to 0.50 mm) thick and not more than 6.0 in. (150.0 mm) wide. 1.5 Units—The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units which are provided for information only and are not considered standard. 1.6 The following safety hazard caveat pertains only to the test method(s) described in this test method. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Test Method for Measuring and Recording the Deviations from Flatness in Copper and Copper Alloy Strip

ASTM B30-10 铜基合金铸锭标准规范

1.1 This specification establishes the requirements for copper alloys in ingot form for remelting for the manufacturing of castings having the Copper Alloy UNS No. designation, commercial designations and nominal composition shown in Table 1 and Table 2. 1.2 A cross reference of Copper Alloy UNS Nos. and copper alloy casting specifications is given in Table 3. 1.3 The values stated in inch-pound units are to be regarded as standard. No other units of measurement are included in this standard.

Standard Specification for Copper Alloys in Ingot Form

ASTM B422/B422M-10e1 铜-铝-硅-钴合金,铜-镍-硅-镁合金,铜-镍-硅合金,铜-镍-铝-镁合金,和铜-镍-锡合金片材和带材标准规格

1.1 This specification establishes the requirements for2 Copper Alloy UNS Nos. C19002, C19010, C19015, ,C19020, C19025, C63800, C64725, C70250, C70260, C70265, and C70310 sheet and strip. 1.2 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Specification for Copper-Aluminum-Silicon-Cobalt Alloy, Copper-Nickel-Silicon-Magnesium Alloy, Copper-Nickel-Silicon Alloy, Copper-Nickel-Aluminum-Magnesium Alloy, and Copper-Nickel-Tin Alloy Sheet and Strip

ASTM B103/B103M-10 磷青铜厚板材、薄板材、带材和轧制棒材标准规范

1.1 This specification establishes copper-tin alloy (phosphor bronze), copper-tin-lead alloy (leaded phosphor bronze), and copper-tin-lead-zinc alloy (bearing bronze), plate, sheet, strip, and rolled bar. The phosphor bronzes commonly are used for deep drawing into bellows and stamping and forming into spring devices and into terminals and connectors for electrical apparatus because they combine high strength with high elongation. The leaded phosphor bronzes are used where strength, corrosion resistance, and machinability are required. The bearing bronze is used in bushings, bearings, and load-bearing thrust washers. The following alloys are covered:

Standard Specification for Phosphor Bronze Plate, Sheet, Strip, and Rolled Bar

ASTM B16/B16M-10(2015) 用于螺丝机的自由切割黄铜棒 棒和形状的标准规格

1.1 This specification establishes the requirements for free-cutting brass rod, bar, wire, and shapes of any specified cross section produced from Copper Alloy UNS Nos. C36000 or C36010 suitable for high-speed screw machining applications and moderate thread rolling. 1.2 Units—Values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard. 1.2.1 Within the text, SI units are shown in brackets. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Specification for Free-Cutting Brass Rod, Bar and Shapes for Use in Screw Machines

ASTM B115-10 电解铜阴极标准规范

Calculated values shall be rounded to the desired number of places as directed in Practice E29. 1.1 This specification establishes the requirements for electrolytic copper cathode; electrorefined and electrowon. 1.2 Units8212;The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. Note 18212;Cathode produced to this specification corresponds to the designation “Cath” as defined in Classification B224 and may be used to produce all other coppers listed in Classification B224 that are normally produced from “Cath” copper. Note 28212;Grade 1 cathode conforms to the chemical compositional requirements of Copper UNS No. C11040, except for oxygen, and is suitable for the manufacture of wire rod as designated in Specification B49. 1.3 The following hazard caveat applies to the test methods described in Annex A2 of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Specification for Electrolytic Copper Cathode

ASTM B968/B968M-10 铜及铜合金管和管道压扁试验的标准试验方法

When properly performed and interpreted, the flattening test will provide information about the relative ductility of a tube and presence of surface defects. For welded tube products, the test will provide information on the integrity of the weld seam. In certain product specifications which establish requirements for tubes of sizes greater than 4 in. [100 mm], the test may be allowed as a substitute to the expansion pin test in B153.1.1 This test method establishes the requirements for the flattening test for copper and copper alloy pipe and tube of all sizes. The method addresses both inch-pound and metric considerations, and both seamless and welded product. 1.2 Units8212;Values stated in either inch-pound units or SI units are to be regarded as standard. Within the text, SI units are shown in brackets. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Test Method for Flattening of Copper and Copper-Alloy Pipe and Tube

ASTM B505/B505M-09 连续浇铸铜合金铸件规格

1.1 This specification establishes requirements for continuously cast rod, bar, tube, and shapes produced from copper alloys with nominal compositions as listed in Table 1. 1.2 Castings produced to this specification may be manufactured for and supplied from stock. In such cases the manufacturer shall maintain heat traceability to specific manufacturing date and chemical analysis. 1.3 The values stated in either SI units or inch/pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Specification for Copper Alloy Continuous Castings

ASTM B43-09 标准尺寸无缝红铜管的标准规范

1.1 This specification establishes requirements for seamless red brass (Copper Alloy UNS No. C23000) pipe in nominal pipe sizes, both regular and extra-strong. In the annealed temper (O61), the pipe is suitable for use in plumbing, boiler feed lines, and for similar purposes. In the drawn general purpose temper (H58), the pipe is suitable for architectural applications, such as guard railings and stair hand railings. 1.2 Units8212;The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.3 The following hazard caveat pertains only to the test method portion, Section 9.1.1, of this specification. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. 1.4 Warning—Mercury has been designated by EPA and many state agencies as a hazardous material that can cause central nervous system, kidney, and liver damage. Mercury, or its vapor, may be hazardous to health and corrosive to materials. Caution should be taken when handling mercury and mercury-containing products. See the applicable product Material Safety Data Sheet (MSDS) for details and EPA’s website (http://www.epa.gov/mercury/faq.htm) for additional information. Users should be aware that selling mercury or mercury-containing products, or both, in your state may be prohibited by state law. (See 9.2.)

Standard Specification for Seamless Red Brass Pipe, Standard Sizes

ASTM B171/B171M-09a 压力容器、冷凝器及热交换器用铜合金中厚板和薄板标准规格

1.1 This specification establishes the requirements for copper-alloy plate, sheet, and circles cut from plate and sheet for pressure vessels, condensers, and heat exchangers. The following alloys are covered: Copper AlloyPreviously Used Designation C36500Leaded Muntz Metal C44300Admirality, Arsenical C44400Admirality, Antimonial C44500Admirality, Phosphorized C46400Naval Brass, Uninhibited C46500Naval Brass, Arsenical C61300Aluminum Bronze C61400Aluminum Bronze D C6300010 % Aluminum-Nickel Bronze C632009 % Aluminum-Nickel Bronze C7060090-10 Copper Nickel C7062090-10 Copper Nickel -(modified for welding) C7150070-30 Copper Nickel C7152070-30 Copper Nickel-(modified for welding) C72200. . . 1.2 Units—The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard.

Standard Specification for Copper-Alloy Plate and Sheet for Pressure Vessels, Condensers, and Heat Exchangers

ASTM B249/B249M-09 锻铜及铜合金棒材,条材,型材和锻件一般要求的标准规范

For the purpose of determining compliance with the specified limits for requirements of the properties listed in the following table and for dimensional tolerances, an observed value or a calculated value shall be rounded as indicated in accordance with the rounding method of Practice E29. Property Rounded Unit for Observed or Calculated Value Chemical compositionnearest unit in the last right-hand significant digit used in expressing the limiting value Hardness Electrical resistivity Electrical conductivity Tensile strengthnearest ksi [5 MPa] Yield strength Elongation:nearest 1 % Grain size: Under 0.060 mmnearest multiple of 0.005 mm 0.060 mm and overnearest 0.01 mm 1.1 This specification establishes the general requirements common to wrought copper and copper alloy rod, bar, shapes, and forgings which shall apply to Specifications B16/B16M, B21/B21M, B98/B98M, B124/B124M, B138/B138M, B139/B139M, B140/B140M, B150/B150M, B151/B151M, B196/B196M, B283, B301/B301M, B371/B371M, B411/B411M, B441, B453/B453M, B455,

Standard Specification for General Requirements for Wrought Copper and Copper-Alloy Rod, Bar, Shapes and Forgings

ASTM B427-09 齿轮用青铜合金铸件的标准规范

1.1 This specification establishes requirements for alloys whose copper alloy numbers and nominal compositions are shown in Table 1. The castings may be furnished as one of three types: static chill, centrifugal chill, or sand cast. 1.2 The values stated in inch-pound units are to be regarded as the standard. SI values given in parentheses are for information purposes only. TABLE 1 Nominal Composition Copper Alloy UNS No.Previously Used DesignationComposition, % CopperTinNickelLeadPhos- phorus C90800A87.812.0...00.2 C91700B86.312.01.500.2 C90700...87.811.0...00.2 C91600C88.010.31.500.2 C92900D83.510.03.52.80.2

Standard Specification for Gear Bronze Alloy Castings

ASTM B770-09 通用铜铍合金砂型铸件标准规范

1.1 This specification establishes requirements for copper-beryllium alloy sand castings for general applications and nominal compositions alloys defined by this specification are shown in Table 1. 1.2 Units8212;The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.3 The following safety hazard caveat pertains only to the test methods described in this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory requirements prior to use. TABLE 1 Nominal Compositions Copper Alloy UNS No.Previous DesignationCopperNickelSiliconBerylliumCobaltChromiumIronZirconiumTinManganese C8140070C99.1......0.06...0.8............ C8200010C97......0.52.5............... C822003C, 14C982.0...0.5.................. C82400A165C, 165CTA97.8......1.70.5............... C82500

Standard Specification for Copper-Beryllium Alloy Sand Castings for General Applications

ASTM B601-09 锻造及铸造的铜和铜合金回火名称与符号的标准分类

Significance8212;This classification establishes an alphanumeric code of the tempers of copper and copper alloy products. Use8212;An alphanumeric code establishes a system by which product tempers in specifications and published data are designated. The letters in the code identify the type of process used to produce the product temper. For example, “H” indicates a temper resulting from cold working. Note 18212;These letters are frequently the same as those used in temper systems of other metal products. Note 28212;Undefined letters, used in prior temper systems and included in this system for reference, are defined in Appendix X1.1.1 This classification establishes temper designations for copper and copper alloys—wrought and cast. The temper designations are classified by the process or processes used in manufacturing the product involved and its resulting properties. It is not a specification of copper and copper alloys. 1.2 The property requirements for the tempers are given in the applicable product specification.

Standard Classification for Temper Designations for Copper and Copper Alloys8212;Wrought and Cast

ASTM B467-09 焊接铜镍管的标准规范

For purposes of determining compliance with the specified limits for requirements of the properties listed in the following table, and observed value or a calculated value shall be rounded as indicated in accordance with the rounding method of Practice E29. PropertyRounded Unit for Observed or Calculated Value Chemical compositionnearest unit in the last right-hand place of figures of the specified limit Tensile strength Yield strengthnearest ksi [nearest MPa up to 10 ksi, incl, nearest 5 MPa over 10 ksi] Elongationnearest 1 %1.1 This specification establishes the requirements for welded copper-nickel alloy pipe for general engineering purposes. The following alloys are covered: Copper Alloy UNS No. Type of Metal C7060090-10 copper-nickel C7062090-10 copper-nickel (Modified for Welding) C7150070-30 copper-nickel C7152070-30 copper-nickel (Modified for Welding) 1.2 Units8212;The values stated in either inch-pound units or SI units are to be regarded separately as standard. Within the text, the SI units are shown in brackets. The values stated in each system are not exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems could result in nonconformance with the specification.

Standard Specification for Welded Copper-Nickel Pipe

ASTM B466/B466M-09 无缝铜镍管的标准规范

1.1 This specification establishes the requirements for seamless copper-nickel pipe and tube in straight lengths, suitable for general engineering purposes. The alloys involved are copper alloys UNS Nos. C70400, C70600, C70620, C71000, C71500, C71520, and C72200. 1.1.1 Copper alloys UNS Nos. C70620 and C71520 are intended for product that will be subsequently welded. 1.2 Units8212;Values stated in inch-pound or SI units are to be regarded separately as standard. Within the text, SI units are shown in brackets. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in nonconformance with the specification. 1.3 The following safety hazard caveat pertains only to the test methods described in the Test Methods section of this specification: 1.3.1 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Specification for Seamless Copper-Nickel Pipe and Tube

ASTM B152/B152M-09 铜片,铜带,铜板和轧制铜条的标准规范

1.1 This specification establishes the requirements for copper sheet, strip, plate, and rolled bar produced from the following coppers. Copper UNS No.APrevious Designation Type of Copper C10100B OFEOxygen-free electronic C10200B OF Oxygen-free without residual deoxidants C10300 ...Oxygen-free extra low phosphorus C10400, C10500, C10700 OFS Oxygen-free, silver bearing C10800 ...Oxygen-free low phosphorus C10910 ...Low oxygen C11000B,C ETP, TPC Electrolytic tough pitchC, Tough pitchC C11300, C11400, C11600B STP Silver bearing tough pitch C12000 DLPPhosphorized, low residual phos- phorus C12200B DHP Phosphorized, high residual phos- phorus C12300 DPSPhosphorized, silver bearing C14200 DPAPhosphorus deoxidized, arsenical C14420 ...Tin bearing tellurium copper C14530 ...Tin tellurium bearing copper _______________ A Except Copper UNS Nos. C10910 (low oxygen), C14200 (phosphorus deoxidized, arsenical), C14420 (tin bearing tellurium), and C14530 (tin tellurium bearing) these types of copper are classified in Classification B224. B SAE Specification CA101 conforms to Copper UNS No. C10100; SAE Specification CA102 conforms to the requirements for Copper UNS No. C10200; SAE Specification CA110 conforms to the requirements for Copper UNS No. C11000; SAE Specifications CA113, CA114, and CA116 c......

Standard Specification for Copper Sheet, Strip, Plate, and Rolled Bar

ASTM B188-09 汇流无缝铜管的标准规范

For purposes of determining compliance with the specified limits for requirements of the properties listed in the following table, an observed value or a calculated value shall be rounded as indicated in accordance with the rounding method of Practice E29. PropertyRounded Unit for Calculated or Observed Value Chemical compositionnearest unit in the last right-hand place of figures of the specified limit Hardness Electrical resistivitynearest unit in the last right-hand place of figures Electrical conductivity Tensile strengthnearest ksi (5 MPa) Elongation: below 5 %nearest multiple of 0.5 % 5 % and overnearest 1 % 1.1 This specification establishes the requirements for seamless copper bus pipe and tube intended for use as electrical conductors. 1.1.1 The product shall be made from one of the following coppers, as denoted in the ordering information: Previously CopperUsed Desig- UNS No. nation Type of Copper C10100 OFE Oxygen-free, electronic C10200 OFOxygen-free without residual deoxidants C10300 —Oxygen-free, extra low phosphorus C10400, C10500, C10700 OFS Oxygen-free, silver bearing C11000 ETPElectrolytic tough pitch C11300, C11400, C11600 STP Silver-bearing tough pitch C12000 DLPPhosphorized, low residual phosphorus 1.2 Unless otherwise specified, any one of the above coppers may be furnished. 1.3 Units8212;Values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units, which are ......

Standard Specification for Seamless Copper Bus Pipe and Tube

ASTM B432-09a 包铜及包铜合金的钢板标准规范

1.1 This specification establishes the requirements for plate of a carbon steel or low-alloy steel base to which is integrally and continuously bonded on one or both sides a layer of copper or copper-base alloy. The material is generally intended for pressure vessel use but may be used in other structural applications where corrosion resistance or conductivity of the alloy is of prime importance. 1.2 Units8212;The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.

Standard Specification for Copper and Copper Alloy Clad Steel Plate