77.150.30 (Copper products) 标准查询与下载

ASTM B587-08 焊接黄铜管标准规范

For the purpose of determining compliance with the specified limits for requirements of the properties listed in the following table, an observed value or a calculated value shall be rounded as indicated in accordance with the rounding method of Practice E 29: PropertyRounded Unit for Observed or Calculated Value Chemical composition Hardnessnearest unit in the last right-hand place of figures of the specified limit Tensile strengthnearest ksi Grain size up to 0.060 mm, inclnearest multiple of 0.005 mm1.1 This specification establishes the requirements for round, rectangular, and square copper alloy welded tube for general engineering applications. 1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.3 The following hazard statement pertains only to the test method described in 18.2.3, 18.2.4, 18.2.6, and 18.2.7 of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Specification for Welded Brass Tube

ASTM B61-08(2013) 蒸气或阀门青铜铸件的标准规格

1.1 This specification2 establishes requirements for a high-grade steam-metal or valve-bronze alloy (Copper Alloy UNS No. C922003) used for component castings of valves, flanges, and fittings. 1.2 The castings covered are used in products that may be manufactured in advance and supplied from stock by the manufacturer or other dealer. 1.3 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.

Standard Specification for Steam or Valve Bronze Castings

ASTM B806-08 通用铜合金永久铸模铸件

1.1 This specification establishes requirements for copper alloy permanent mold castings for general applications. Nominal compositions of the alloys under this specification are shown in Table 1. 1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.

Standard Specification for Copper Alloy Permanent Mold Castings for General Applications

ASTM B770-08 通用铜铍合金砂型铸件标准规范

1.1 This specification establishes requirements for copper-beryllium alloy sand castings for general applications and nominal compositions alloys defined by this specification are shown in Table 1. 1.2 Units8212;The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.3 The following safety hazard caveat pertains only to the test methods described in this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory requirements prior to use.

Standard Specification for Copper-Beryllium Alloy Sand Castings for General Applications

ASTM B30-08a 铝合金6061-T6标准结构型材的标准规范

1.1 This specification establishes the requirements for copper alloys in ingot form for remelting for the manufacturing of castings having the Copper Alloy UNS No. designation, commercial designations and nominal composition shown in Table 1 and Table 2. 1.2 A cross reference of Copper Alloy UNS Nos. and copper alloy casting specifications is given in Table 3. 1.3 The values stated in inch-pound units are to be regarded as standard. No other units of measurement are included in this standard.

Standard Specification for Copper Alloys in Ingot Form

ASTM B61-08 蒸气或阀门青铜铸件的标准规范

1.1 This specification establishes requirements for a high-grade steam-metal or valve-bronze alloy (Copper Alloy UNS No. C92200 ) used for component castings of valves, flanges, and fittings. 1.2 The castings covered are used in products that may be manufactured in advance and supplied from stock by the manufacturer or other dealer. 1.3 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.

Standard Specification for Steam or Valve Bronze Castings

ASTM B134/B134M-08 黄铜线的标准规范

1.1 This specification establishes requirements for round, hexagonal, octagonal, rectangular and square brass wire of UNS Alloy Nos. C21000, C22000, C22600, C23000, C23400, C24000, C26000, C27000, and C27400. 1.2 Units8212;The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard.

Standard Specification for Brass Wire

ASTM B301/B301M-08 易切削铜条材、棒材、线材和型材的标准规范

1.1 This specification establishes the requirements for free-cutting copper rod, bar, wire, and shapes of UNS Alloy Nos. C14500, C14510, C14520, C14700, and C18700, suitable for high-speed screw machine work or for general applications. 1.2 Typically, product made to this specification is furnished as straight lengths. Sizes ½ in. [12 mm] and under may be furnished in coils when requested. 1.3 Units8212;The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard.

Standard Specification for Free-Cutting Copper Rod, Bar, Wire, and Shapes

ASTM B505/B505M-08a 铜合金连铸件标准规范

1.1 This specification establishes requirements for continuously cast rod, bar, tube, and shapes produced from copper alloys with nominal compositions as listed in Table 1. 1.2 Castings produced to this specification may be manufactured for and supplied from stock. In such cases the manufacturer shall maintain heat traceability to specific manufacturing date and chemical analysis. 1.3 The values stated in either SI units or inch/pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. TABLE 1 Nominal Composition Copper Alloy UNS No.DesignationComposition, % CopperTinLeadZincNickelAluminumIronManganese C83600leaded red brass85555............ C83800leaded red brass82.93.866.5............ C84200leaded semi-red brass8052.513............ C84400leaded semi-red brass802.978.5............ C84800leaded semi-red brass76

Standard Specification for Copper Alloy Continuous Castings

ASTM B591-08 铜锌锡和铜锌锡铁镍合金板、薄板、带材及轧制的棒材标准规范

1.1 This specification covers the requirements for specified copper-zinc-tin alloys and copper-zinc-tin-iron-nickel alloys in the form of plate, sheet, strip, and rolled bar. The alloys and nominal compositions are as follows: Copper Alloy UNS No. Copper, %Tin, %Zinc, %Phos., %%Iron, %Nickel, % C405009514 C4081095.52.02.220.030.10.15 C4085095.53.01.270.10.10.1 C4086094.82.03.040.030.030.1 C41100910.58.5 C413009118 C415009127 C4220087112 C4250088210 C4252089.82.07.970.10.10.1 C4300085213 C43400850.714.3 1.2 T......

Standard Specification for Copper-Zinc-Tin and Copper-Zinc-Tin-Iron-Nickel Alloys Plate, Sheet, Strip, and Rolled Bar

ASTM B122/B122M-08 铜镍锌合金(镍银)及铜镍合金板、薄板、带材和轧制棒材的标准规格

1.1 This specification establishes the requirements for copper-nickel-tin alloy, copper-nickel-zinc alloy (nickel silver), and copper-nickel alloy plate, sheet, strip, and rolled bar. The following alloys are covered: Previously Copper AlloyUsed Nominal Composition, UNS No. Designation% Copper Nickel Zinc TinChro- mium C70600...9010 ......... C70620...8610......... C7100068020 ......... C7150057030 ......... C71520...6531......... C72200...8515 ......0.5 C72500...89 9 ...2... C7350017218 10...... C7400097010 20............

Standard Specification for Copper-Nickel-Tin Alloy, Copper-Nickel-Zinc Alloy (Nickel Silver), and Copper-Nickel Alloy Plate, Sheet, Strip, and Rolled Bar

ASTM B2-08 中等硬度冷拉铜丝标准规范

1.1 This specification covers medium-hard-drawn round copper wire for electrical purposes (see Explanatory Note 1). 1.2 The SI values of density and resistivity are to be regarded as standard. For all other properties the inch-pound values are to be regarded as standard, and the SI units may be approximate. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Specification for Medium-Hard-Drawn Copper Wire

ASTM B505/B505M-08 铜合金连铸件标准规范

1.1 This specification establishes requirements for continuously cast rod, bar, tube, and shapes produced from copper alloys with nominal compositions as listed in Table 1. 1.2 Castings produced to this specification may be manufactured for and supplied from stock. In such cases the manufacturer shall maintain heat traceability to specific manufacturing date and chemical analysis. 1.3 The values stated in either SI units or inch/pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the specification. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Specification for Copper Alloy Continuous Castings

ASTM B271-08e1 铜基合金离心铸件的技术规范

1.1 This specification establishes requirements for centrifugal castings of copper-base alloys having the nominal compositions shown in Table 1. 1.2 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard.

Standard Specification for Copper-Base Alloy Centrifugal Castings

ASTM B36/B36M-08a 黄铜板、薄板、带材及轧制棒材的标准规范

1.1 This specification establishes the requirements for brass plate, sheet, strip, and rolled bar of the following alloys: Copper Alloy UNS No.Previous Trade NameNominal Composition Copper, %Zinc, % C21000Gilding, 95 %955 C22000Commerical Bronze, 90 %9010 C22600Jewerly Bronze, 87½ %87.512.5 C23000Red Brass, 85 %8515 C24000Low Brass, 80 %8020 C26000Cartridge Brass, 70 %7030 C26800Yellow Brass, 66 %6634 C27200…6337 C28000Muntz Metal, 60 %6040 1.2 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard.

Standard Specification for Brass Plate, Sheet, Strip, And Rolled Bar

ASTM B98/B98M-08 铜硅合金杆材、棒材和型材标准规范

1.1 This specification establishes requirements for copper-silicon rod, bar, and shapes for UNS Alloys C65100, C65500, and C66100. Note 18212;Material for hot forging is covered by Specification B 124/B 124M. Note 28212;For ASME Boiler and Pressure Vessel Code applications, see Specification SB-98 in Section II of that code. 1.2 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard.

Standard Specification for Copper-Silicon Alloy Rod, Bar and Shapes

ASTM B453/B453M-08 铜锌铅合金(含铅青铜)杆材,棒材和型材标准规范

1.1 This specification establishes the requirements for copper-zinc-lead alloy (leaded-brass) rod, bar, wire, and shapes produced from Copper Alloys UNS Nos. C33500, C34000, C34500, C35000, C35300, C35330, and C35600. These alloys have nominal composition given in Table 1. 1.1.1 This product is suitable for applications requiring extensive machining before such cold-forming operations as swaging, flaring, severe knurling, or thread rolling. Note 18212;Refer to Appendix X1 for additional applications information. 1.1.2 Typically, product made to this specification is furnished as straight lengths. Sizes ½ in. [12 mm] and under may be furnished as wire in coils or on reels when requested. 1.2 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard. Note 28212;Refer to Specifications B 16/B 16M and B 140/B 140M for copper-zinc-lead (leaded-brass) rod and bar for screw machine applications. TABLE 1 Nominal Composition, % Copper Alloy UNS No.CopperZinc Lead C3350063.536.00.5 C3400063.535.31.2 C3450063.534.52.0 C3500061.537.11.4 C3530061.536.52.0 C3533061.835.72.5 C3560061.536.02.5

Standard Specification for Copper-Zinc-Lead Alloy (Leaded-Brass) Rod, Bar, and Shapes

ASTM B100-08 桥梁和其它结构用锻制铜合金轴承和膨胀中厚板及薄板的标准规范

1.1 This specification establishes the requirements for wrought copper-alloy bearing plate and bearing sheets for application in bridges and other structures. Specifically, the plates and sheets are to be used for fixed or expansion bearings where the motion is slow and intermittent with pressures not exceeding 3 ksi (20 MPa). 1.2 Units8212;Values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.

Standard Specification for Wrought Copper-Alloy Bearing and Expansion Plates and Sheets for Bridge and Other Structural Use

ASTM B22-08 同心绞捻的铜与包铜钢丝并合导线标准规范

1.1 This specification establishes requirements for bronze castings for turntables, movable bridges and bridge parts, and bronze castings suitable for use in bridges and other structures for fixed and expansion bearings in which motion is slow and intermittent. The following Copper Alloys are specified: UNS No. C86300, C90500, C91100, C91300, and C93700. Note 18212;Historically, the alloys in this specification have been used in the applications listed in Appendix X1. Actual practice may vary. 1.2 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Specification for Bronze Castings for Bridges and Turntables

ASTM B411/B411M-08 铜镍硅合金杆材和棒材的标准规格

1.1 This specification establishes the requirements for copper-nickel-silicon alloy rod and bar produced from Copper Alloy UNS No. C64700 in straight lengths. 1.2 Units8212;The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard.

Standard Specification for Copper-Nickel-Silicon Alloy Rod and Bar