77.150.30 (Copper products) 标准查询与下载

ASTM B505/B505M-08 铜合金连铸件标准规范

1.1 This specification establishes requirements for continuously cast rod, bar, tube, and shapes produced from copper alloys with nominal compositions as listed in Table 1. 1.2 Castings produced to this specification may be manufactured for and supplied from stock. In such cases the manufacturer shall maintain heat traceability to specific manufacturing date and chemical analysis. 1.3 The values stated in either SI units or inch/pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the specification. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Specification for Copper Alloy Continuous Castings

ASTM B806-08a 通用铜合金永久铸模铸件的标准规范

1.1 This specification establishes requirements for copper alloy permanent mold castings for general applications. Nominal compositions of the alloys under this specification are shown in Table 1. 1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. TABLE 1 Nominal Composition ClassificationCopper Alloy UNS No.Nominal Composition CopperAluminumIronManganeseNickel (incl Cobalt)SiliconLeadZincTin Aluminum bronzeC95300 C95400 C9541089.0 85.0 84.010.0 11.0 10.01.0 4.0 4.0... ... ...... ... 2.0... ... ...... ... ...... ... ...... ... ... Nickel aluminum bronzeC95500 C9580081.0 81.311.0 9.04.0 4.0... 1.24.0 4.5... ...... ...... ...... ... Silicon brassC87500 C8780082.0 82.0... ...... ...... ...... ...4.0 4.0... ...14.0 14.0... ... C87850A76.0. . .. . .. . .. . .3.0. . .20.9. . . Lead-free yellow brassBC8954061.00.400.30

Standard Specification for Copper Alloy Permanent Mold Castings for General Applications

ASTM B194-08 铜铍合金中厚板、薄板、带材和轧制棒材标准规范

These test methods are primarily intended to test for compliance with composition specifications. It is assumed that all who use these test methods will be trained analysts capable of performing common laboratory procedures skillfully and safely. It is expected that work will be performed in a properly equipped laboratory.1.1 This specification establishes the requirements for copper-beryllium alloy plate, sheet, strip, and rolled bar. The following alloys are specified: Copper AlloyPreviously Used CommercialNominal Beryllium UNS No. DesignationsContent, % C17000Alloy 1651.7 C17200Alloy 251.9 1.2 Unless otherwise specified in the contract or purchase order, Copper Alloy UNS No. C17200 shall be the alloy furnished. 1.3 Units8212;The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.4 The following hazard statement pertains only to the test method portions in the annex of this specification: 1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Specification for Copper-Beryllium Alloy Plate, Sheet, Strip, and Rolled Bar

ASTM B587-08 焊接黄铜管标准规范

For the purpose of determining compliance with the specified limits for requirements of the properties listed in the following table, an observed value or a calculated value shall be rounded as indicated in accordance with the rounding method of Practice E 29: PropertyRounded Unit for Observed or Calculated Value Chemical composition Hardnessnearest unit in the last right-hand place of figures of the specified limit Tensile strengthnearest ksi Grain size up to 0.060 mm, inclnearest multiple of 0.005 mm1.1 This specification establishes the requirements for round, rectangular, and square copper alloy welded tube for general engineering applications. 1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.3 The following hazard statement pertains only to the test method described in 18.2.3, 18.2.4, 18.2.6, and 18.2.7 of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Specification for Welded Brass Tube

ASTM B61-08 蒸气或阀门青铜铸件的标准规范

1.1 This specification establishes requirements for a high-grade steam-metal or valve-bronze alloy (Copper Alloy UNS No. C92200 ) used for component castings of valves, flanges, and fittings. 1.2 The castings covered are used in products that may be manufactured in advance and supplied from stock by the manufacturer or other dealer. 1.3 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.

Standard Specification for Steam or Valve Bronze Castings

ASTM B584-08a 一般用途铜合金砂铸件标准规范

1.1 This specification covers requirements for copper alloy sand castings for general applications. Nominal compositions of the alloys defined by this specification are shown in Table 1. This is a composite specification replacing former documents as shown in Table 1. Note 18212;Other copper alloy castings are included in the following ASTM specifications: B 22, B 61, B 62, B 66, B 67, B 148, B 176, B 271, B 369, B 427, B 505/B 505M, B 763, B 770, and B 806. 1.2 Component part castings produced to this specification may be manufactured in advance and supplied from stock. In such cases the manufacturer shall maintain a general quality certification of all castings without specific record or date of casting for a specific casting. 1.3 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. TABLE 1 Nominal Compositions ClassificationCopper Alloy UNS No. Previous Designation Commercial DesignationCopperTinLeadZincNickelIronAlum- inumMan- ganeseSili- conNio- biumBis- muth Leaded red brassC83450. . . . . .88 2½ 2 6½1. . .. . . . . .. . .. . .. . . C83600B 145-4A85-5-5-5 or No. 1 composition85 5 5 5. . .. . .. . . . . .. . .. . .. . . C83800

Standard Specification for Copper Alloy Sand Castings for General Applications

ASTM B61-08(2013) 蒸气或阀门青铜铸件的标准规格

1.1 This specification2 establishes requirements for a high-grade steam-metal or valve-bronze alloy (Copper Alloy UNS No. C922003) used for component castings of valves, flanges, and fittings. 1.2 The castings covered are used in products that may be manufactured in advance and supplied from stock by the manufacturer or other dealer. 1.3 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.

Standard Specification for Steam or Valve Bronze Castings

ASTM B22-08 同心绞捻的铜与包铜钢丝并合导线标准规范

1.1 This specification establishes requirements for bronze castings for turntables, movable bridges and bridge parts, and bronze castings suitable for use in bridges and other structures for fixed and expansion bearings in which motion is slow and intermittent. The following Copper Alloys are specified: UNS No. C86300, C90500, C91100, C91300, and C93700. Note 18212;Historically, the alloys in this specification have been used in the applications listed in Appendix X1. Actual practice may vary. 1.2 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Specification for Bronze Castings for Bridges and Turntables

ASTM B763-08 阀门用铜合金砂型铸件标准规范

1.1 This specification establishes requirements for copper alloy sand castings for valve applications. Nominal compositions of the alloys defined by this specification are shown in Table 1. Note 18212;This specification does not cover Copper Alloy UNS Nos. C83600, C92200, C96200, and C96400. These alloys are also used in valve applications. They are covered by the following specifications: C83600: B 62 C92200: B 61 C96200: B 369 C96400: B 369 1.2 The castings produced under this specification are used in products which may be manufactured in advance and supplied for sale from stock by the manufacturer. 1.3 Units8212;The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.

Standard Specification for Copper Alloy Sand Castings for Valve Applications

ASTM B534-07 铜-钴-铍合金及铜-镍-铍合金厚板材、薄板材、带材和轧制棒材的标准规范

1.1 This specification establishes the requirements for plate, sheet, strip, and rolled bar. The following alloys are included: PreviouslyNominal Composition, %Copper AlloyUsedUNS No.DesignationBerylliumCobaltNickelC17500Alloy 100.62.5?/TD>C17510Alloy 3 or 140.4?/TD>1.81.2 The intent is to provide a system of interchangeable alloys.1.3 Units8212;Values stated in inch-pound units are to be regarded standard. The values given in brackets are mathematical conversions to SI units, which are provided for information only. 1.4 The following safety hazard caveat pertains only to the test methods described in this specification:1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Specification for Copper-Cobalt-Beryllium Alloy and Copper-Nickel-Beryllium Alloy Plate, Sheet, Strip, and Rolled Bar

ASTM B508-07 挠性金属软管用铜合金带材的标准规范

1.1 This specification establishes the requirements for annealed copper-alloy strip for the manufacture of flexible metal hose produced from Copper Alloy UNS Nos. C41100 and C50500.1.1.1 The nominal compositions are as follows: Copper AlloyUNS No.CopperZincTin C4110091.08.50.5 C5050098.7...1.31.2 The values stated in inch-pound units are to be regarded as the standard, except grain size, which is given in SI units. The values given in parentheses are for information only.The following precautionary statement pertains only to the test method portion, Section 13, of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Specification for Copper Alloy Strip for Flexible Metal Hose

ASTM B248M-07 锻制铜和铜合金厚板材、薄板材、带材及轧制棒材的一般要求的标准规范(米制)

1.1 This specification establishes the general requirements common to several wrought product specifications. Unless otherwise specified in the purchase order or in an individual specification, these general requirements shall apply to copper and copper-alloy plate, sheet, strip, and rolled bar supplied under each of the following product specifications issued by ASTM: B 36/B 36M, B 96/B 96M, B 103/B 103M, B 121/B 121M, B 122/B 122M, B 152/B 152M, B 169/B 169M, B 194, B 422, B 465, B 534, B 591, B 592, B 694, B 740, B 747, and B 768. 1.2 Units - This specification is the companion specification to inch-pound Specification B 248.1.3 This test method covers the determination of sulfur in electrolytic cathode copper.This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Specification for General Requirements for Wrought Copper and Copper-Alloy Plate, Sheet, Strip, and Rolled Bar [Metric]

ASTM B608-07 焊接铜合金管的标准规范

1.1 This specification establishes the requirements for arc-welded pipe for use in brackish water or seawater piping systems.1.2 Units - The values stated in inch-pound units are regarded as the standard. The values given in parentheses are mathematical conversions to SI units which are provided for information only and are not considered standard.The following hazard statement pertains only to the test method described in 8.2 and 14.3.2 of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Specification for Welded Copper-Alloy Pipe

ASTM B505/B505M-07 铜合金连铸件标准规范

1.1 This specification establishes requirements for continuously cast rod, bar, tube, and shapes produced from copper alloys with nominal compositions as listed in .1.2 Castings produced to this specification may be manufactured for and supplied from stock. In such cases the manufacturer shall maintain heat traceability to specific manufacturing date and chemical analysis.1.3 The values stated in inch/pound or SI units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in nonconformance with the specification.This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Specification for Copper Alloy Continuous Castings

ASTM B139/B139M-07 磷青铜条材、棒材和型材的标准规范

1.1 This specification establishes the requirements for phosphor bronze rod, bar, and shapes.1.2 UnitsThe values stated in inch-pound units or SI units are to be regarded separately in the standard. Within the text, the SI values are given in brackets. The values stated in each system are not exact equivalents; each system of units is independent of the other. Combining values from the two systems may result in nonconformance with the specification.

Standard Specification for Phosphor Bronze Rod, Bar, and Shapes

ASTM B601-07 铜和铜合金用回火标志的标准分类.锻造和铸造

Significance8212;This classification establishes an alphanumeric code of the tempers of copper and copper alloy products. Use8212;An alphanumeric code establishes a system by which product tempers in specifications and published data are designated. 4.2.1 The letters in the code identify the type of process used to produce the product temper. For example, “H” indicates a temper resulting from cold working. Note 18212;These letters are frequently the same as those used in temper systems of other metal products. Note 28212;Undefined letters, used in prior temper systems and included in this system for reference, are defined in Appendix X1.1.1 This classification establishes temper designations for copper and copper alloys8212;wrought and cast. The temper designations are classified by the process or processes used in manufacturing the product involved and its resulting properties. It is not a specification of copper and copper alloys.1.2 The property requirements for the tempers are given in the applicable product specification.

Standard Classification for Temper Designations for Copper and Copper Alloys8212;Wrought and Cast

ASTM B543-07 焊接的铜及铜合金热交换管用标准规范

1.1 This specification covers welded tube of copper and various copper alloys up to 3 1/8 in., inclusive, in diameter, for use in surface condensers, evaporators, heat exchangers, and general engineering applications. The following coppers or copper alloys are involved:Copper or Copper Alloy UNS No. 2Previously Used DesignationType of MetalC10800...oxygen-free, low phosphorusC12200DHP phosphorized, high residual phosphorusC19400...copper-iron alloyC23000...red brassC44300...arsenical admiraltyC44400...antimonial admiraltyC44500...phosphorized admiraltyC68700...arsenical aluminum brassC70400...95-5 copper-nickelC70600...90-10 copper-nickelC70620...90-10 copper-nickel (Modified for Welding)C71000...80-20 copper-nickelC71500...70-30 copper-nickelC71520...70-30 copper-nickel (Modified for Welding)C71640...copper-nickel-iron-manganeseC72200...... 1.2 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. (Warning8212;Mercury is a definite health hazard in use and disposal. (See 12.1.1.))

Standard Specification for Welded Copper and Copper-Alloy Heat Exchanger Tube

ASTM B298-07 镀银的软或退火铜线用标准规范

1.1 This specification covers silver-coated, soft or annealed, round copper wire, intended for use in electrical equipment, as follows:1.1.1 Class A - Wire whose silver coating is at least 1.25 % of the total weight of the coated wire.1.1.2 Class B - Wire whose silver coating is at least 2.50 % of the total weight of the coated wire.1.1.3 Class C - Wire whose silver coating is at least 4.00 % of the total weight of the coated wire.1.1.4 Class D - Wire whose silver coating is at least 6.10 % of the total weight of the coated wire.1.1.5 Class E - Wire whose silver coating is at least 10.00 % of the total weight of the coated wire.1.2 Silver-coated wire having different minimum percentages of silver by weight may be obtained by mutual agreement between the manufacturer and the purchaser. For information purposes the thickness of coating in microinches provided by the percentages listed above is shown in (Explanatory ).1.3 The SI values of resistance and density are to be regarded as standard. For all other properties values stated in inch-pound units are to be regarded as the standard. The values given in parentheses are provided for information purposes only.The following precautionary caveat pertains only to the test method section of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. For specific precautionary statements see Table 1 and Explanatory Note 1.

Standard Specification for Silver-Coated Soft or Annealed Copper Wire

ASTM B103/B103M-07 磷青铜板材,带材和轧材标准规范

1.1 This specification establishes copper-tin alloy (phosphor bronze), copper-tin-lead alloy (leaded phosphor bronze), and copper-tin-lead-zinc alloy (bearing bronze), plate, sheet, strip, and rolled bar. The phosphor bronzes commonly are used for deep drawing into bellows and stamping and forming into spring devices and into terminals and connectors for electrical apparatus because they combine high strength with high elongation. The leaded phosphor bronzes are used where strength, corrosion resistance, and machinability are required. The bearing bronze is used in bushings, bearings, and load-bearing thrust washers. The following alloys are covered:Note 1 - All of the above alloys contain small amounts of phosphorus, used as a deoxidant in melting, and to enhance the mechanical properties.1.2 The values stated in either inch-pound units or SI units are to be regarded separately as standard. Within the text, the SI units are shown in brackets. The values stated in each system are not exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in nonconformance with the specification.

Standard Specification for Phosphor Bronze Plate, Sheet, Strip, and Rolled Bar

ASTM B101-07 建筑结构用包铅铜薄板材和带材的标准规范

1.1 This specification establishes the requirements for lead-coated copper sheet and strip in flat lengths (or in coils) in ounce-weight thicknesses for roofing, flashing, gutters, downspouts, and for the general sheet metalwork in building construction. The lead coating is applied by hot dipping.1.2 Materials made to this specification are not intended for electrical applications.1.3 Units - Values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units, which are provided for information only and are not considered standard. Note 1 - A companion specification for copper sheet and strip for building construction is Specification B 370.The following hazard caveat pertains to the test method portion, Section 17, of this specification. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Specification for Lead-Coated Copper Sheet and Strip for Building Construction