77.150.50 钛产品 标准查询与下载

DIN 17862:2012 钛和锻钛合金棒材.技术规范

Titanium and titanium alloy bars - Technical specification

NB/T 20008.15-2012 压水堆核电厂用其他材料.第15部分：3级板式热交换器用钛板

本部分规定了厚度小于等于1.5mm的钛板的制造、化学成分、力学性能、试验和检验等技术要求。 本部分适用于压水堆核电厂3级板式热交换器用深冲成型的最大厚度为1.5mm的钛板。

Other material for pressurized water reactor nuclear power plants.Part 15：Titanium plate for use in the fabracation of class 3 heat exchanger plates

YS/T 750-2011 热轧钛带卷

本标准规定了热轧钛带卷的要求、试验方法、检验规则、标志、包装、运输、贮存及质量证明书与合同（或订货单）内容。 本标准适用于热轧方法生产的各种用途的钛带卷。

Hot rolled titanium coil

YS/T 749-2011 电站冷凝器和热交换器用钛-钢复合管板

本标准规定了电站冷凝器和热交换器使用的以钛及钛合金为复材，碳素钢、低合金钢为基材，用爆炸焊接法制造的复合管板的要求、试验方法、检验规则及标志、包装、运输、贮存、质量证明书和合同（或订货单）内容。 本标准适用于总厚度等于或大于24mm的冷凝器和热交换器用爆炸焊接钛-钢复合管板（以下简称复合板）。

Titanium-steel clad tubesheet for condenser and heat exchanger used in electric power station

ASTM B898-11(2016) 反应性和难熔金属复合板的标准规格

1.1 This specification covers plate consisting of a base metal to which is bonded, integrally and continuously, on one or both sides a layer of one of the following: titanium, zirconium, tantalum, niobium, and their alloys. The material generally is intended for pressure vessel use. 1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. The values in parentheses and in metric tables are provided for information only.

Standard Specification for Reactive and Refractory Metal Clad Plate

KS D 0079-2010 钛焊接管压差测试方法

이 표준은 타이타늄 용접관(이하 용접관이라 한다.)의 기밀성을 확인하기 위한 차압 시험(이

Differential pressure testing method of titanium welded tubes

KS D 0079-2010(2020) 钛焊接管的压差测试方法

Differential pressure testing method of titanium welded tubes

DIN 17860:2010 钛和钛合金钢带、薄板材和带材.交付技术条件

The standard specifies the technical conditions of delivery of titanium and titanium alloy strip and sheet.

Titanium and titanium alloy strip, sheet and plate - Technical conditions of delivery

ASTM E1320-10 钛铸件用标准参考射线照片

These reference radiographs are designed so that acceptance standards, which may be developed for particular requirements, can be specified in terms of these radiographs. The radiographs are of castings that were produced under conditions designed to produce the discontinuities. The reference radiographs are intended to be used for casting thickness ranges in accordance with Table 1 and Table 2.1.1 The reference radiographs provided in the adjunct to this standard are reproductions of original radiographs and are supplied as a means for establishing some of the categories and severity levels of discontinuities in titanium castings that may be revealed by radiographic examination. Use of this standard for the specification or grading of castings requires procurement of the adjunct reference radiographs which illustrate the discontinuity types and severity levels. They should be used in accordance with contractual specifications. Note 18212;The original radiographs produced for Volume I were taken with X-rays in the range of 110 KV to 220 KV. The original radiographs produced for Volume II were taken with X-rays in the range of 200 K to 340 KV. 1.2 These film reference radiographs are not intended to illustrate the types and degrees of discontinuities found in titanium castings when performing digital radiography. If performing digital radiography of titanium castings, refer to Digital Reference Image Standard E2669. 1.3 These reference radiographs consist of two volumes. Volume I, described in Table 1, is applicable to a wall thickness of up to 1 in. (0 to 25.4 mm). Volume II, described in Table 2, is applicable to a wall thickness of over 1 in. to 2 in. (25.4 mm to 50.8 mm). The standard may be used, where there is no other applicable standard, for other thicknesses for which agreement has been reached between purchaser and manufacturer. Note 28212;The reference radiographs are not impacted by this revision. There have been no revisions to the adjunct reference radiographs since original issue. The adjunct reference radiographs of any issue remain valid and may be used to this standard. 1.4 The plates produced to serve for use in this standard were purposely cast to exhibit the desired discontinuity. The plates were cast using different processes as shown in Table 1 and Table 2. Hot isostatic pressing was not used on any of the plates. 1.5 The values stated in inch-pound units are to be regarded as the standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.6 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Reference Radiographs for Titanium Castings

ASTM B381-10e1 钛及钛合金锻件标准规格

1.1 This specification covers 39 grades of annealed titanium and titanium alloy forgings as follows:

Standard Specification for Titanium and Titanium Alloy Forgings

KS D 5604-2009 钛棒

이 표준은 어닐링한 타이타늄 및 타이타늄합금의 봉(이하 봉이라 한다.)에 대하여 규정한다.

Titanium and titanium alloys－Rods and bars

KS D 5576-2009 钛与钛合金.电线

이 표준은 단면의 모양이 원형이며 또한 지름이 8 mm 미만이고, 압연한 그대로 또는 압연

Titanium and titanium alloys－Wires

ASTM B367-08 钛和钛合金铸件的标准规范

1.1 This specification covers titanium and titanium alloy castings intended for general corrosion resistant and industrial applications. 1.2 This specification is intended for use of purchasers and/or producers of reactive metal castings for defining the requirements and assuring the properties of castings for unique corrosion-resistant applications, that is, not for commodity items which must meet all potential purchasers'' requirements. 1.2.1 Users are advised to use the specification as a basis for obtaining castings which will meet minimum acceptance requirements established and revised by consensus of the members of the committee. 1.2.2 User requirements considered more stringent may be met by the addition to the purchase order of one or more supplementary requirements, which may include, but are not limited to, those listed in Sections S1 through S8. 1.3 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.

Standard Specification for Titanium and Titanium Alloy Castings

YS/T 310-2008 热镀用锌合金锭

本标准规定了热镀用锌合金链的要求、试验方法、检验规则及标志、包装、运输与贮存。 本标准适用于钢材热镀用锌合金绽。

Zinc alloy ingot for hot dip galvanizing

JIS H 4670:2007 钛和钛合金.线材

この規格は，断面の形状が円形，かつ，径が8 mm未満であり，圧延したまま，又は圧延後焼なましを行ったチタン及びチタン合金の線(以下，“線”という。)について規定する。ただし，80種については，固溶化熱処理を行った線だけに適用する。

Titanium and titanium alloys -- Wires

JIS H 4657:2007 钛和钛合金.锻件

この規格は，焼なましを行ったチタン及びチタン合金の鍛造品(以下，“鍛造品”という。)について規定する。ただし，80種については，固溶化熱処理を行った鍛造品だけに適用する。

Titanium and titanium alloys -- Forgings

JIS H 4650:2007 钛和钛合金.杆材和棒材

この規格は，焼なましを行ったチタン及びチタン合金の棒(以下，“棒”という。)について規定する。ただし，断面の形状が円形，かつ，径が8 mm未満のものには適用しない。80種については，固溶化熱処理を行った棒だけに適用する。

Titanium and titanium alloys -- Rods and bars

YS/T 654-2007 钛粉

本标准规定了钛粉的要求、试验方法、检验规则及标志、包装、运输、贮存和订单要求。 本标准适用于采用氢化-脱氢法生产的粉末冶金用或作为添加剂用钛粉。

Titanium powder

YS/T 351-2007 钛铁矿精矿

本标准规定了钛铁矿精矿的要求、试验方法、检验规则和标志、包装、运输、贮存等。 本标准适用于以含钛原矿为原料，经选矿富集获得的主要供生产高钛渣、金红石、钛白等使用的钛铁矿精矿。

Ilmenite concentrate

ASTM B348-06a 钛及钛合金棒材和坯料的标准规范

Standard Specification for Titanium and Titanium Alloy Bars and Billets