79.040 木材、原木和锯材 标准查询与下载

ASTM D2555-17a 建立透明木材强度值的标准实践

1.1 This practice covers the determination of strength values for clear wood of different species in the unseasoned condition, unadjusted for end use, applicable to the establishment of design values for different solid wood products such as lumber, laminated wood, plywood, and round timbers. Presented are: 1.1.1 Procedures by which test values obtained on small clear specimens may be combined with density data from extensive forest surveys to make them more representative, 1.1.2 Guidelines for the interpretation of the data in terms of assigned values for combinations of species or regional divisions within a species to meet special marketing needs, and 1.1.3 Information basic to the translation of the clear wood values into design values for different solid wood products for different end uses. 1.1.4 For species where density survey data are not as yet available for the re-evaluation of average strength properties, the presently available data from tests made under the sampling methods and procedures of Test Methods D143 or Practice E105 are provided with appropriate provision for their application and use. Because of the comprehensive manner in which the density survey is undertaken, it follows that the reevaluated strength data are intended to be representative of the forest stand, or rather large forest subdivisions. 1.1.5 Some useful mechanical properties (tensile strengths parallel and perpendicular to grain, modulus of rigidity for a 1 This practice is under the jurisdiction of ASTM Committee D07 on Wood and are the direct responsibility of Subcommittee D07.02 on Lumber and Engineered Wood Products. Current edition approved Aug. 1, 2017. Published October 2017. Originally approved in 1966. Last previous edition approved in 2017 as D2555 – 17. DOI: 10.1520/D2555-17A. Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee. 1 longitudinal-transverse plane, and transverse modulus of elasticity) have not been extensively evaluated. Methods are described for estimating these properties by their relation to other properties. 1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Practice for Establishing Clear Wood Strength Values

ISO 13061-15:2017 木材的物理和机械性能小型透明木材试样的试验方法第15部分:径向和切向膨胀的测定

This document specifies a method for the determination of linear swelling in the radial and tangential directions of wood.

Physical and mechanical properties of wood — Test methods for small clear wood specimens — Part 15: Determination of radial and tangential swelling

ISO 13061-16:2017 木材的物理和机械性能 - 小透明木材试样的试验方法 - 第16部分:体积溶胀的测定

This document specifies methods for the determination of volumetric swelling of wood.

Physical and mechanical properties of wood — Test methods for small clear wood specimens — Part 16: Determination of volumetric swelling

ISO 13061-2:2014/Amd 1:2017 木材的物理和机械性能小型透明木材试样的试验方法第2部分:物理和机械试验密度的测定修改1

Physical and mechanical properties of wood — Test methods for small clear wood specimens — Part 2: Determination of density for physical and mechanical tests — Amendment 1

ISO 13061-1:2014/Amd 1:2017 木材的物理和机械性能.小型透明木材试样的试验方法.第1部分:物理和机械试验用含水量的测定.修改件1

Physical and mechanical properties of wood — Test methods for small clear wood specimens — Part 1: Determination of moisture content for physical and mechanical tests — Amendment 1

ISO 13061-3:2014/Amd 1:2017 木材的物理和机械性能小型透明木材试样的试验方法第3部分:静态弯曲极限强度的测定修改1

Physical and mechanical properties of wood — Test methods for small clear wood specimens — Part 3: Determination of ultimate strength in static bending — Amendment 1

ISO 13061-4:2014/Amd 1:2017 木材的物理和机械性能小型透明木材试样的试验方法第4部分:静态弯曲弹性模量的测定修改1

Physical and mechanical properties of wood — Test methods for small clear wood specimens — Part 4: Determination of modulus of elasticity in static bending — Amendment 1

LY/T 2872-2017 木制珠串

wooden bead string

DIN EN 350 Berichtigung 1:2017 木材和木制品的耐久性. 木材和木质材料生物制剂耐久性的试验和分类; 德文版本EN 350-2016, DIN EN 350-2016-12勘误表

Durability of wood and wood-based products - Testing and classification of the durability to biological agents of wood and wood-based materials; German version EN 350:2016, Corrigendum to DIN EN 350:2016-12

DB45/T 1523-2017 红木锯材干燥质量等级

Mahogany sawn timber dry quality grades

17/30340323 DC BS ISO 13912 结构木材 机器强度分级 基本原则

BS ISO 13912. Structural timber. Machine strength grading. Basic principles

ASTM D1666-17 木材和木基面板材料进行加工试验的标准试验方法

1.1 These test methods cover procedures for planing, routing/shaping, turning, mortising, boring, and sanding, all of which are common wood-working operations used in the manufacture of wood products. These tests apply, in different degrees, to two general classes of materials: 1.1.1 Wood in the form of lumber, and 1.1.2 Wood-base panel materials such as plywood and wood-base fiber and particle panels. 1.2 Because of the importance of planing, some of the variables that affect the results of this operation are explored with a view to determining optimum conditions. In most of the other tests, however, it is necessary to limit the work to one set of fairly typical commercial conditions in which all the different woods are treated alike. 1.3 Several factors enter into any complete appraisal of the machining properties of a given wood or wood-base panel. Quality of finished surface is recommended as the basis for evaluation of machining properties. Rate of dulling of cutting tools and power consumed in cutting are also important considerations but are beyond the scope of these test methods. 1.4 Although the methods presented include the results of progressive developments in the evaluation of machining properties, further improvements may be anticipated. For example, by present procedures, quality of the finished surface is evaluated by visual inspection, but as new mechanical or physical techniques become available that will afford improved precision of evaluation, they should be employed. 1.5 The values stated in inch-pound units are to be regarded as the standard. The metric equivalents of inch-pound units may be approximate. 1.6 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. 1.7 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Methods for Conducting Machining Tests of Wood and Wood-Base Panel Materials

GOST R 57737-2017 树干 测量方法

Trunks. Methods of measuring

GOST R 57738-2017 砍倒的树干 规格

Felled trunks. Specifications

DIN 4072:2017 针叶木材制成的舌榫板

This standard applies to planed spliced boards of softwood. Profiles and board widths also apply to rough sawn timber. The sorting takes place according to DIN 68365. The short codes for the type of wood are to be specified according to DIN EN 13556.This standard does not apply to floor boards according to DIN EN 13990.

Boards tongued and grooved made of coniferous timber

KS F 2198-2016 木材密度和比重的测定

Determination of density and specific gravity of wood

KS F 3124-2016 缓慢燃烧的木材

Slow-burning lumbers

GSO ISO 2301:2016 阔叶树种锯材 缺陷 测量

1.1 This International Standard specifies international methods of measuring defects of sawn timber of broadleaved species, classified in ISO 2299, Sawn timber of broadleaved species—Defects—Classification. 1.2 This International Standard covers unplaned sawn timber and sawn timber surfaced to size or planed but without profiling.

Sawn timber of broadleaved species -- Defects -- Measurement

GSO ISO 17959:2016 实木地板的一般要求

This International Standard specifies the requirements and test methods of characteristics of solid wood flooring boards for internal (interior) use as flooring. It also specifies packaging and marking requirements. It is applicable to both finished and unfinished solid wood flooring board. Solid wood parquet is not covered.

General requirements for solid wood flooring

GSO ISO 8904:2016 阔叶锯材 尺寸 测量方法

This International Standard specifies the methods of measurement of the length, width, thickness and volume of broadleaved sawn timber. It is applicable to unplaned, square-edged and unedged broadleaved sawn timber.

Broadleaved sawn timber -- Sizes -- Methods of measurement