79.060.10 胶合板 标准查询与下载

GOST 8673-2018 胶合板台面 技术条件

Plywood panels. Specifications

GOST 10636-2018 木制碎料板 测定垂直于板面的极限抗张强度的方法

Wood-shaving and wood-fiber plates. Strength definition method at stretching perpendicularly plate layer

GOST 3916.2-2018 具有针叶树薄板外层的通用胶合板 技术条件

Plywood for general use with outer layers of coniferous veneer. Specifications

ASTM D2559-12a(2018) 外部暴露条件下使用的粘结结构木制品粘合剂标准规范

1.1 This specification covers adhesives suitable for the bonding of wood, including treated wood, into structural wood products for general construction or other uses where a high-strength, durable adhesive bond is required. 1.2 This specification includes test methods that may be referenced by specific product standards for the evaluation and approval of structural wood adhesives. Methods are included to evaluate adhesives intended for use in exterior exposure. NOTE 1—Consult the Commentary in Appendix X1 regarding the intent and limitations of each test method contained in this specification. 1.3 Description of Bondline Performance—It is recognized that structural wood adhesives are used in various applications and levels of severity in terms of moisture content, loading, cyclic and seasonal weather conditions, heat exposure and other use conditions. It is the intent of this standard to determine the suitability of an adhesive for use under various levels of severity and conditions with specific and appropriate test methods and requirements. NOTE 2—This specification does not contain specific tests outlined for different chemical types of adhesives. 1.4 Strength and durability requirements of the adhesive are based on the performance of the adhesive in laminated wood as measured by: 1.4.1 Resistance to shear by compression loading after conditioning to the target moisture content indicated in 14.2.3 and meeting requirements in 14.4. 1.4.2 Resistance to delamination during exposure to three cycles of vacuum pressure wetting followed by drying at elevated temperature as indicated in 15.3 and meeting requirements in 15.4. 1.4.3 Resistance to creep under static load by subjecting test specimens to a specified shear stress and exposing one set of test specimens to an environment of elevated temperature and ambient humidity and another set to an environment of high humidity and meeting requirements set forth in 16.3. 1.4.4 For applications involving chemical treatment, the adhesive shall be evaluated using representative samples of treated wood. NOTE 3—When using chemically treated wood, compatibility between the treatment, adhesive, and wood is to be considered and agreed upon between the chemical manufacture and the user. NOTE 4—Additional durability testing may also be required as specified by individual product standards. Consult the Commentary in Appendix X1 for additional information and guidance as to the type of durability testing that may be appropriate to supplement this specification when characterizing the adhesive for suitability with specific wood products. 1 This specification is under the jurisdiction of ASTM Committee D14 on Adhesives and is the direct responsibility of Subcommittee D14.30 on Wood Adhesives. Current edition approved Aug. 1, 2018. Published August 2018. Originally approved in 1966. Last previous edition approved in 2012 as D2559 – 12aɛ1 . DOI: 10.1520/D2559-12AR18. Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee. 1 1.5 The evaluation of adhesives for use in ground contact and marine exposures are beyond the scope of this specification. 1.6 The evaluation of binder adhesives is beyond the scope of this specification. 1.7 The values stated in SI units are to be regarded as the standard. The values in parentheses are for information only. 1.8 The text of this specification references notes, footnotes and a commentary which provide explanatory material. These notes, footnotes and commentary (excluding those in tables and figures) shall not be considered as requirements of the specification. 1.9 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.10 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Adhesives for Bonded Structural Wood Products for Use Under Exterior Exposure Conditions

KS F 2159-1-2017 非结构人造板弯曲试验方法

Method of bending test for nonstructural wood-based panels

KS F 2159-2-2017 结构用人造板弯曲试验方法

Method of bending test for structural wood-based panels

ISO 2074:2007/Amd 1:2017 胶合板.词汇.修改件1

Plywood — Vocabulary — Amendment 1

LY/T 2879-2017 装饰微薄木

decorative thin wood

LY/T 2875-2017 难燃细木工板

Flame retardant blockboard

DB45/T 1541-2017 融安香杉实木生态板生产技术规程

Technical Regulations for the Production of Rongan Fir Wood Ecological Board

DB35/T 1658-2017 浸渍胶膜纸饰面复合实木板

本标准规定了浸渍胶膜纸饰面复合实木板的术语和定义、分类、要求、试验方法、检验规则以及标 志、包装、运输和贮存。 本标准适用于以实木拼板为基材与浸渍胶膜纸饰面人造板复合而成的装饰板材。

Impregnated film paper facing composite solid wood board

T/LZBX 002-2017 香杉实木板芯

香杉实木板芯的板芯规格尺寸和偏差、板芯平面度、边缘直度、修补、外观、物理性能。

xiangsha solid wood core

CSA O151-17:2017 加拿大软木胶合板

1.1 This Standard applies to exterior bond, all-veneer plywood that has a minimum of three plies and whose outermost plies have parallel grain direction. 1.2 This Standard specifies requirements for a) a quality system; b) ply species; c) materials; d) panel construction; e) bonding; f) veneer and panel grades; g) dimensions and tolerances; h) marking; and i) testing. 1.3 In this Standard, “shall” is used to express a requirement, i.e., a provision that the user is obliged to satisfy in order to comply with the Standard; “should” is used to express a recommendation or that which is advised but not required; and “may” is used to express an option or that which is permissible within the limits of the Standard. Notes accompanying clauses do not include requirements or alternative requirements; the purpose of a note accompanying a clause is to separate from the text explanatory or informative material. Notes to tables and figures are considered part of the table or figure and may be written as requirements. Annexes are designated normative (mandatory) or informative (non-mandatory) to define their application.

Canadian softwood plywood

GOST 34034-2017 层压胶合木 分类

Laminated glued wood. Classification

GSO ASTM D2559:2016 外部暴露条件下使用的粘合结构木制品粘合剂的标准规范

This specification covers adhesives suitable for the bonding of wood, including treated wood, into structural laminated wood products for general construction, for marine use, or for other uses where a high-strength, waterproof adhesive bond is required. The requirements of the adhesive are based on the performance of the adhesive in laminated wood as measured by the following test methods: resistance to shear by compression loading; resistance to delamination during accelerated exposure to wetting and drying; and resistance to deformation under static load. The wood shall be prepared by ambient curing and hot press curing. This abstract is a brief summary of the referenced standard. It is informational only and not an official part of the standard; the full text of the standard itself must be referred to for its use and application. ASTM does not give any warranty express or implied or make any representation that the contents of this abstract are accurate, complete or up to date.

Standard Specification for Adhesives for Bonded Structural Wood Products for Use Under Exterior Exposure Conditions

T/ZZB 0159-2016 细木工板

本标准规定了细木工板的术语和定义、分类和命名、基本要求、技术要求、检验方法、检验规则、标志、标签、包装和贮运、质量承诺。 本标准适用于由木条沿顺纹方向组成板芯，两面与单板或胶合板组坯胶合而成的细木工板。

Blockboard

T/ZZB 0123-2016 浸渍胶膜纸饰面胶合板

本标准规定了浸渍胶膜纸饰面胶合板的术语和定义、分类、基本要求、技术要求、检验方法、检验规则、标志、包装、运输和贮存以及质量承诺。 本标准适用于以胶合板为基材，以浸渍胶膜纸为饰面材料且经热压而成的装饰板材。

Plywood overlaid with thermosetting resin impregnated paper

T/ZZB 0104-2016 装饰单板贴面人造板

本标准规定了装饰单板贴面人造板的术语和定义、分类、基本要求、技术要求、检验方法、检验规则、标志、包装、运输和贮存以及质量承诺。 本标准适用于以普通单板、调色单板、集成单板和重组装饰单板等为饰面材料，以人造板为基材经胶合制成的未经涂饰加工的装饰单板贴面人造板。

Decorative veneered wood-based panel

KS F 3107-2016 刨切单板覆盖胶合板

Sliced veneer overlaid plywood

KS F 3106-2016 预制、印刷、压花和纸质贴面胶合板

Prefinished, printed, embossed & paper overlaid plywood