81.040.10 原材料和未加工的玻璃 标准查询与下载

JC/T 2201-2022 镀膜玻璃用靶材

本文件规定了镀膜玻璃用靶材的分类、要求、检验方法、检验规则、包装、标志、运输与贮存。 本文件适用于建筑用真空磁控溅射镀膜玻璃使用的靶材，其他镀膜玻璃用靶材可参照使用。

Target material for coated glass

JC/T 2167-2022 玻璃釉料

本文件规定了玻璃釉料的分类、要求、试验方法、检验规则以及标志、包装、运输和贮存等。 本文件适用于建筑玻璃及工业玻璃用玻璃釉料。 本文件不适用于数码打印用玻璃釉料、汽车玻璃及太阳能光伏双玻组件中背板玻璃用玻璃釉料。

glass glaze

ASTM C169-16(2022) 钠石灰和硼硅酸盐玻璃化学分析的标准试验方法

1.1 These test methods cover the quantitative chemical analysis of soda-lime and borosilicate glass compositions for both referee and routine analysis. This would be for the usual constituents present in glasses of the following types: (1) soda-lime silicate glass, (2) soda-lime fluoride opal glass, and (3) borosilicate glass. The following common oxides, when present in concentrations greater than indicated, are known to interfere with some of the determinations in this method: 2 % barium oxide (BaO), 0.2 % phosphorous pentoxide (P2O5), 0.05 % zinc oxide (ZnO), 0.05 % antimony oxide (Sb2O3), 0.05 % lead oxide (PbO). 1.2 The analytical procedures, divided into two general groups, those for referee analysis, and those for routine analysis, appear in the following order: Sections Procedures for Referee Analysis: Silica 10 BaO, R2O2 (Al2O3 + P2O5), CaO, and MgO 11 – 15 Fe2O3, TiO2, ZrO2 by Photometry and Al2O3 by Complexiometric Titration 16 – 22 Cr2O3 by Volumetric and Photometric Methods 23 – 25 MnO by the Periodate Oxidation Method 26 – 29 Na2O by the Zinc Uranyl Acetate Method and K2O by the Tetraphenylborate Method 30 – 33 SO3 (Total Sulfur) 34 – 35 As2O3 by Volumetric Method 36 – 40 Procedures for Routine Analysis: Silica by the Single Dehydration Method 42 – 44 Al2O3, CaO, and MgO by Complexiometric Titration, and BaO, Na2O, and K2O by Gravimetric Method 45 – 51 BaO, Al2O3, CaO, and MgO by Atomic Absorption; and Na2O and K2O by Flame Emission Spectroscopy 52 – 59 SO3 (Total Sulfur) 60 B2O3 61 – 62 Fluorine by Pyrohydrolysis Separation and Specific Ion Electrode Measurement 63 – 66 P2O5 by the Molybdo-Vanadate Method 67 – 70 Colorimetric Determination of Ferrous Iron Using 1,10 Phenanthroline 71 – 76 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Methods for Chemical Analysis of Soda-Lime and Borosilicate Glass

ASTM C729-11(2022) 用水槽浮子比较仪测定玻璃密度的标准试验方法

1.1 This test method covers the determination of the density of glass or nonporous solids of density from 1.1 g ⁄cm3 to 3.3 g ⁄cm3 . It can be used to determine the apparent density of ceramics or solids, preferably of known porosity. 1.2 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.3 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Method for Density of Glass by the Sink-Float Comparator

ASTM C829-81(2022) 用梯度炉法测量玻璃液相线温度的标准实施规程

1.1 These practices cover procedures for determining the liquidus temperature (Note 1) of a glass (Note 1) by establishing the boundary temperature for the first crystalline compound, when the glass specimen is held at a specified temperature gradient over its entire length for a period of time necessary to obtain thermal equilibrium between the crystalline and glassy phases. NOTE 1—These terms are defined in Terminology C162. 1.2 Two methods are included, differing in the type of sample, apparatus, procedure for positioning the sample, and measurement of temperature gradient in the furnace. Both methods have comparable precision. Method B is preferred for very fluid glasses because it minimizes thermal and mechanical mixing effects. 1.2.1 Method A employs a trough-type platinum container (tray) in which finely screened glass particles are fused into a thin lath configuration defined by the trough. 1.2.2 Method B employs a perforated platinum tray on which larger screened particles are positioned one per hole on the plate and are therefore melted separately from each other.2 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Practices for Measurement of Liquidus Temperature of Glass by the Gradient Furnace Method

ASTM C1720-21 测定废玻璃和模拟废玻璃液相线温度的标准试验方法

1.1 These test methods cover procedures for determining the liquidus temperature (TL) of nuclear waste, mixed nuclear waste, simulated nuclear waste, or hazardous waste glass in the temperature range from 600 °C to 1600 °C. This test method differs from Practice C829 in that it employs additional methods to determine TL. TL is useful in waste glass plant operation, glass formulation, and melter design to determine the minimum temperature that must be maintained in a waste glass melt to make sure that crystallization does not occur or is below a particular constraint, for example, 1 volume % crystallinity or T1%. As of now, many institutions studying waste and simulated waste vitrification are not in agreement regarding this constraint (1).2 1.2 Three methods are included, differing in (1) the type of equipment available to the analyst (that is, type of furnace and characterization equipment), (2) the quantity of glass available to the analyst, (3) the precision and accuracy desired for the measurement, and (4) candidate glass properties. The glass properties, for example, glass volatility and estimated TL, will dictate the required method for making the most precise measurement. The three different approaches to measuring TL described here include the following: Gradient Temperature Furnace Method (GT), Uniform Temperature Furnace Method (UT), and Crystal Fraction Extrapolation Method (CF). This procedure is intended to provide specific work processes, but may be supplemented by test instructions as deemed appropriate by the project manager or principle investigator. The methods defined here are not applicable to glasses that form multiple immiscible liquid phases. Immiscibility may be detected in the initial examination of glass during sample preparation (see 9.3). However, immiscibility may not become apparent until after testing is underway. 1.3 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Methods for Determining Liquidus Temperature of Waste Glasses and Simulated Waste Glasses

KS B ISO 12844-2021 光学玻璃原料 金刚石颗粒可磨性 试验方法和分类

Raw optical glass－Grindability with diamond pellets－Test method and classification

GSO ISO 9689:2021 光学玻璃原料 50℃下耐碱性磷酸盐洗涤剂水溶液的侵蚀 测试和分类

Specifies a method for testing the resistance of raw optical glasses and a classification of optical glasses according to the aqueous alkaline phosphate-containing detergent resistance (phosphate resistance) determined by this method.

Raw optical glass — Resistance to attack by aqueous alkaline phosphate-containing detergent solutions at 50 degrees C — Testing and classification

ASTM C146-21 玻璃砂化学分析的标准试验方法

1.1?These test methods cover the chemical analysis of glass sands. They are useful for either high-silica sands (99 % + silica (SiO2)) or for high-alumina sands containing as much as 12 to 13 % alumina (Al2O3). Generally nonclassical, these test methods are rapid and accurate. T

Standard Test Methods for Chemical Analysis of Glass Sand

ASTM C730-98(2021) 玻璃压痕硬度标准试验方法

1.1 This test method covers the determination of the Knoop indentation hardness of glass and the verification of Knoop indentation hardness testing machines using standard glasses. 1.2 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.3 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Method for Knoop Indentation Hardness of Glass

DIN ISO 12123:2020 光学和光子学. 毛坯光学玻璃的规格(ISO 12123-2018)

This document gives rules for the specification of raw optical glass. It serves as a complement to the ISO 10110 series, which provides rules specifying finished optical elements. Since raw optical glass can be quite different in shape and size from the optical elements, its spec

Optics and photonics - Specification of raw optical glass (ISO 12123:2018)

T/SDG 002-2020 中空玻璃用干燥剂中掺杂物（氯化钙、氧化钙）检出的试验方法

本标准规定了中空玻璃用干燥剂（3A分子筛、B类干燥剂）定义及术语，掺杂物（氯化钙、氧化钙）检出的试验方法、原理及目的、风险判定、检验规则及报告等。 本标准适用于中空玻璃用干燥剂中0.5%(质量分数)以上掺杂物（氯化钙、氧化钙）的测定。 根据中空玻璃用干燥剂材料的特性，主要在掺杂物（氯化钙/氧化钙)的鉴别检验、掺杂物（氯化钙/氧化钙)含量等开展试验研究。

Test method for detection of dopant (calcium chloride, calcium oxide) in desiccant for insulating glass

ASTM C336-71(2020) 通过纤维伸长率的玻璃退火点和应变点的标准测试方法

1.1 This test method covers the determination of the annealing point and the strain point of a glass by measuring the viscous elongation rate of a fiber of the glass under prescribed condition. 1.2 The annealing and strain points shall be obtained by following the specified procedure after calibration of the apparatus using fibers of standard glasses having known annealing and strain points, such as those specified and certified by the National Institute of Standards and Technology (NIST)2 (see Appendix X1). 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Method for Annealing Point and Strain Point of Glass by Fiber Elongation

ASTM C770-16(2020) 玻璃应力测量的标准试验方法&x2014；光学系数

1.1 This test method covers procedures for determining the stress-optical coefficient of glass, which is used in photoelastic analyses. In Procedure A the optical retardation is determined for a glass fiber subjected to uniaxial tension. In Procedure B the optical retardation is determined for a beam of glass of rectangular cross section when subjected to four-point bending. In Procedure C, the optical retardation is measured for a beam of glass of rectangular cross-section when subjected to uniaxial compression. 1.2 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.3 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Method for Measurement of Glass Stress—Optical Coefficient

KS L 2101-2019 硅砂和石英的化学分析

Chemical analysis of silica sand and quartz

ASTM C657-19 玻璃的D-C体积电阻率的标准测试方法

1.1 This test method covers the determination of the dc volume resistivity of a smooth, preferably polished, glass by measuring the resistance to passage of a small amount of direct current through the glass at a voltage high enough to assure adequate sensitivity. This current must be measured under steady-state conditions that is neither a charging current nor a space-charge, buildup polarization current. 1.2 This test method is intended for the determination of resistivities less than 1016 Ω·cm in the temperature range from 25 °C to the annealing point of the glass. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. For specific hazard statements, see Section 5. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Method for D-C Volume Resistivity of Glass

ASTM C598-93(2019) 弯曲点玻璃退火点和应变点的标准测试方法

1.1 This test method covers the determination of the annealing point and the strain point of a glass by measuring the rate of midpoint viscous bending of a simply loaded glass beam.2 However, at temperatures corresponding to the annealing and strain points, the viscosity of glass is highly time-dependent. Hence, any viscosities that might be derived or inferred from measurements by this procedure cannot be assumed to represent equilibrium structural conditions. 1.2 The annealing and strain points shall be obtained following a specified procedure after direct calibration of the apparatus using beams of standard glasses having known annealing and strain points such as those supplied and certified by the National Institute of Standards and Technology.3 1.3 This test method, as an alternative to Test Method C336 is particularly well suited for glasses that for one reason or another are not adaptable for flame working. It also has the advantages that thermal expansion and effective length corrections, common to the fiber elongation method, are eliminated. 1.4 The values stated in metric units are to be regarded as the standard. The values given in parentheses are for information only. 1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Method for Annealing Point and Strain Point of Glass by Beam Bending

ASTM C338-93(2019) 玻璃软化点的标准试验方法

1.1 This test method covers the determination of the softening point of a glass by determining the temperature at which a round fiber of the glass, nominally 0.65 mm in diameter and 235 mm long with specified tolerances, elongates under its own weight at a rate of 1 mm/min when the upper 100 mm of its length is heated in a specified furnace at the rate of 5 6 1 °C ⁄min. 1.2 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Method for Softening Point of Glass

T/ZBH 012-2019 被动式超低能耗建筑透明部分用玻璃

本标准规定了被动式超低能耗建筑透明部分用玻璃的术语和定义、分类、规格与结构、材料与构造、要求、试验方法、检验规则、包装、标志、运输和贮存等。 本标准适用于被动式超低能耗建筑外围护结构透明部分用玻璃。

Glass for the transparent part of passive ultra-low energy consumption building

T/ZBH 011-2019 高性能节能玻璃技术条件

本标准规定了高性能节能玻璃的术语和定义、分类与结构、材料与构造、要求和试验方法。 本标准适用于建筑外围护结构用高性能节能玻璃。

Technical requirements for high performance energy efficient glass