81.040.10 原材料和未加工的玻璃 标准查询与下载

T/ZBH 009-2019 建筑用硼硅酸盐防火玻璃

本标准规定了建筑用硼硅酸盐防火玻璃的术语和定义、分类及标记、总则、要求、试验方法、检验规则、标志、包装、运输和贮存。 本标准适用于经热处理钢化工艺制造的建筑用硼硅酸盐防火玻璃。其他用途应用可参照本标准使用。

Borosilicate fire-resistant glass in building

ASTM C978-04(2019) 使用偏光显微镜和光学延迟补偿程序对透明玻璃基体中的残余应力进行光弹性测定的标准测试方法

1.1 This test method covers the determination of residual stresses in a transparent glass matrix by means of a polarizing microscope using null or retardation compensation procedures. 1.2 Such residual stress determinations are of importance in evaluating the nature and degree of residual stresses present in glass matrixes due to cord, or the degree of fit, or suitability of a particular combination of glass matrix and enamel, or applied color label (ACL). 1.3 The retardation compensation method of optically determining and evaluating enamel or ACL residual stress systems offers distinct advantages over methods requiring physical property measurements or ware performance tests due to its simplicity, reproducibility, and precision. 1.4 Limitations—This test method is based on the stressoptical retardation compensation principle, and is therefore applicable only to transparent glass substrates, and not to opaque glass systems. 1.5 Due to the possibility of additional residual stresses produced by ion exchange between glasses of different compositions, some uncertainty may be introduced in the value of the stress optical coefficient in the point of interest due to a lack of accurate knowledge of chemical composition in the areas of interest. 1.6 This test method is quantitatively applicable to and valid only for those applications where such significant ion exchange is not a factor, and stress optical coefficients are known or determinable. 1.7 The extent of the ion exchange process, and hence the magnitudes of the residual stresses produced due to ion exchange will depend on the exchange process parameters. The residual stress determinations made on systems in which ion exchange has occurred should be interpreted with those dependencies in mind. 1.8 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only. 1.9 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.10 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Method for Photoelastic Determination of Residual Stress in a Transparent Glass Matrix Using a Polarizing Microscope and Optical Retardation Compensation Procedures

BS ISO 12123:2018 光学和光子学 光学玻璃原片规格

What is this ISO 12123 - Optics and photonics — Specification of raw optical glass   about?    ISO 12123 gives rules for the specification of raw optical glass. It serves as a complement to the ISO 10110 series, which provides rules specifying finished optical elements. Since raw optical glass can be quite different in shape and size from the optical elements, its specification also differs from that of optical elements.   ISO 12123 introduces definitions, reference formulae and data needed for calculating the deviation of the relative partial dispersion from the normal line. This quantity serves to value the suitability of optical glasses for colour aberration correction beyond achromatic correction of only two colours.  

Optics and photonics. Specification of raw optical glass

ISO 12123:2018 光学和光子学 - 原始光学玻璃的规格

This document gives rules for the specification of raw optical glass. It serves as a complement to the be quite different in shape and size from the optical elements, its specification also differs from that of optical elements. This document provides guidelines for the essential specification characteristics of raw optical glass in order to improve communication between glass suppliers and optical element manufacturers. For specific applications (e.g. lasers, the infrared spectral range), specifications based on this document need supplements. While the intent of this document is to address the specific needs of raw optical glass, many of the parameters and characteristics are common to other optical materials, which are not necessarily glass. While this document can be used for non-glass materials, the user is informed that only optical glass has been considered in the development of this document, and other materials can have issues, which have not been taken into consideration. NOTE Additional information on how to translate optical element specifications into raw optical glass specifications is given in Annex A.

Optics and photonics — Specification of raw optical glass

ASTM C1663-18 用蒸汽水化试验测量废玻璃或玻璃陶瓷耐久性的标准试验方法

1.1 The vapor hydration test method can be used to study the corrosion of a waste forms such as glasses and glass ceramics2 upon exposure to water vapor at elevated temperatures. In addition, the alteration phases that form can be used as indicators of those phases that may form under repository conditions. These tests; which allow altering of glass at high surface area to solution volume ratio; provide useful information regarding the alteration phases that are formed, the disposition of radioactive and hazardous components, and the alteration kinetics under the specific test conditions. This information may be used in performance assessment (McGrail et al, 2002 (1)3 for example). 1.2 This test method must be performed in accordance with all quality assurance requirements for acceptance of the data. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Method for Measuring Waste Glass or Glass Ceramic Durability by Vapor Hydration Test

T/ZBH 007-2018 全氧燃烧超白压花玻璃单位产品能源消耗限额

本标准规定了全氧燃烧超白压花玻璃单位产品能源消耗（下称能耗）限额的术语和定义、要求、统计范围和计算方法、节能管理与措施。 本标准适用于全氧燃烧超白压花玻璃生产企业能耗的计算、考核及新建项目的能耗控制。

The norm of energy consumption per unit product of ultra-clear patterned glass by oxygen fuel combustion process

ASTM E1640-18 用动态力学分析法分配玻璃化转变温度的标准试验方法

1.1 This test method covers the assignment of a glass transition temperature (Tg) of materials using dynamic mechanical analyzers. 1.2 This test method is applicable to thermoplastic polymers, thermoset polymers, and partially crystalline materials which are thermally stable in the glass transition region. 1.3 The applicable range of temperatures for this test method is dependent upon the instrumentation used, but, in order to encompass all materials, the minimum temperature should be about −150 °C. 1.4 This test method is intended for materials having an elastic modulus in the range of 0.5 MPa to 100 GPa. 1.5 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.6 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.7 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Method for Assignment of the Glass Transition Temperature By Dynamic Mechanical Analysis

T/ZBH 006-2018 高光热比本体着色平板玻璃

本标准规定了高光热比本体着色平板玻璃的术语和定义、分类、要求、试验方法、检验规则、标志、包装、运输和贮存。

Body tinted flat glass with high light-to-heat ratio

JC/T 2450-2018 被动房透明部分用玻璃

本标准规定了被动房透明部分用玻璃的术语和定义、分类和规格、材料、要求、试验方法、检验规则以及标志、包装、运输和贮存等。 本标准适用于被动房外围护结构透明部分用中空玻璃、真空复合中空玻璃制品等。

Glass used in the transparent part of passive building

ASTM E1640-13(2018) 用动态力学分析法分配玻璃化转变温度的标准试验方法

Standard Test Method for Assignment of the Glass Transition Temperature By Dynamic Mechanical Analysis

ASTM C1720-17 测定废玻璃和模拟废玻璃的液相线温度的标准试验方法

Standard Test Method for Determining Liquidus Temperature of Waste Glasses and Simulated Waste Glasses

ASTM C1720-17e1 测定废玻璃和模拟废玻璃的液相线温度的标准试验方法

Standard Test Method for Determining Liquidus Temperature of Waste Glasses and Simulated Waste Glasses

ASTM F2980-13(2017) 用现场便携式X射线荧光（XRF）分析玻璃中重金属的标准试验方法

1.1 This test method covers field portable X-ray fluorescence (XRF) spectrometric procedures for analyses of arsenic and lead in glass compositions using field portable energy dispersive XRF spectrometers. 1.2 The mass fraction range of arsenic within which this test method is quantitative is given in Table 1. Scope limits were determined from the interlaboratory study results using the approach given in Practice E1601. 1.3 The mass fraction range for which lead was tested is given in Table 1. However, lead results cannot be considered quantitative on the basis of single-sample results because the precision performance is not good enough to allow laboratories to compare results in a quantitative manner. NOTE 1—The performance of this test method was evaluated using results based on single-sample determinations from specimens composed of glass beads. One laboratory has determined that performance can be significantly improved by basing reported results on the mean of determinations from multiple samples to overcome inherent heterogeneity of elements in glass beads, especially the element lead. Additional information is provided in Section 17 on Precision and Bias. 1.3.1 To obtain quantitative performance, lead results must consist of the average of four or more determinations. 1.4 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. Some specific hazards statements are given in Section 7 on Hazards. 1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Method for Analysis of Heavy Metals in Glass by Field Portable X-Ray Fluorescence (XRF)

ASTM E708-79(2017) 废玻璃作为玻璃容器制造原料的标准规范

1.1 This specification covers particulate glass (cullet material, recovered from waste destined for disposal, smaller than 6 mm intended for reuse as a raw material in the manufacture of glass containers. 1.2 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.2.1 Exception—The values given in parentheses are for information only. 1.3 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Waste Glass as a Raw Material for the Manufacture of Glass Containers

ASTM C1663-17 利用蒸汽水合试验测定废玻璃或玻璃陶瓷耐久性的标准试验方法

5.1 The vapor hydration test can be used to study the corrosion of glass and glass ceramic waste forms under conditions of high temperature and contact by water vapor or thin films of water. This method may serve as an accelerated test for some materials, since the high temperatures will accelerate thermally activated processes. A wide range of test temperatures have been reported in the literature –40°C (Ebert et al, 2005 (3), for example) to 300°C (Vienna et al, 2001 (4), for example). It should be noted that with increased test temperature comes the possibility of changing the corrosion rate determining mechanism and the types of phases formed upon alteration from those that occur in the disposal environment (Vienna et al, 2001 (4)). 5.2 The vapor hydration test can be used as a screening test to determine the propensity of waste forms to alter and for relative comparisons in alteration rates between waste forms. 1.1 The vapor hydration test method can be used to study the corrosion of a waste forms such as glasses and glass ceramics2 upon exposure to water vapor at elevated temperatures. In addition, the alteration phases that form can be used as indicators of those phases that may form under repository conditions. These tests; which allow altering of glass at high surface area to solution volume ratio; provide useful information regarding the alteration phases that are formed, the disposition of radioactive and hazardous components, and the alteration kinetics under the specific test conditions. This information may be used in performance assessment (McGrail et al, 2002 (1)3 for example). 1.2 This test method must be performed in accordance with all quality assurance requirements for acceptance of the data. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Method for Measuring Waste Glass or Glass Ceramic Durability by Vapor Hydration Test

KS B ISO 12844:2016 未加工光学玻璃 金刚砂可磨性 试验方法和分类

Raw optical glass－Grindability with diamond pellets－Test method and classification

KS B ISO 11455-2016 原光学玻璃 - 双折射的测定

Raw optical glass－Determination of birefringence

KS B ISO 12844-2016 光学玻璃原料金刚石颗粒可磨性试验方法和分类

Raw optical glass－Grindability with diamond pellets－Test method and classification

KS B ISO 11455-2016(2021) 未加工光学玻璃双折射率的测定

Raw optical glass－Determination of birefringence

KS B ISO 9689-2016(2021) 未加工光学玻璃－在50℃下耐碱性磷酸盐洗涤剂水溶液侵蚀性－试验和分类

Raw optical glass－Resistance to attack by aqueous alkaline phosphate- containing detergent solutions at 50 ℃－Testing and classification