81.040.10 原材料和未加工的玻璃 标准查询与下载

JC/T 2278-2014 加工玻璃安全生产规程

本标准规定了加工玻璃安全生产的基本要求、生产过程要求以及检验、包装、贮存和运输等。本标准适用于加工玻璃企业的建设及安全生产和管理。

The specifications for production safety in glass processing

JC/T 2277-2014 安全玻璃生产规程 第2部分:汽车用安全玻璃生产规程

本部分规定了汽车用安全玻璃生产过程的术语和定义、分类、材料、生产、检验以及包装、标志、运输和储存等。本部分适用于汽车用安全玻璃的生产,其他道路车辆用安全玻璃的生产可参照本规程。

Specification for safety glass manufacture process.Part 2: Specification for automotive safety glass manufacture process

JC/T 2201-2013 镀膜玻璃用靶材

本标准规定了镀膜玻璃用靶材的术语和定义、分类、要求、检验方法、检验规则以及标志、包装、运输和贮存等。本标准适用于建筑用真空磁控溅射镀膜玻璃使用的靶材,其他镀膜玻璃用靶材可参照使用。

Targets for coated glass

ASTM C657-93(2013) 玻璃的D-C体积电阻率的标准测试方法

1.1 This test method covers the determination of the dc volume resistivity of a smooth, preferably polished, glass by measuring the resistance to passage of a small amount of direct current through the glass at a voltage high enough to assure adequate sensitivity. This current must be measured under steady-state conditions that is neither a charging current nor a space-charge, buildup polarization current. 1.2 This test method is intended for the determination of resistivities less than 1016 Ω·cm in the temperature range from 25°C to the annealing point of the glass. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. For specific hazard statements, see Section 5.

Standard Test Method for D-C Volume Resistivity of Glass

ASTM C730-98(2013) 标准测试方法为 Knoop玻璃压痕硬度

1.1 This test method covers the determination of the Knoop indentation hardness of glass and the verification of Knoop indentation hardness testing machines using standard glasses. 1.2 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Test Method for Knoop Indentation Hardness of Glass

GSO ISO 8424:2013 光学玻璃原料 25℃下耐酸性水溶液的侵蚀 测试方法和分类

This International Standard specifies a method for testing the resistance of raw optical glasses to attack by aqueous acidic solutions at 25 °C and a classification of optical glasses according to the acid resistance determined by this method. This International Standard contains basic information about the chemical durability of the glass tested. It is applicable to samples of raw optical glasses. NOTE 1 The test method may also be used for other types of glasses.

Raw optical glass - Resistance to attack by aqueous acidic solutions at 25 degrees C - Test method and classification

JC/T 2167-2013 玻璃釉料

本标准规定了玻璃釉料的术语和定义、分类、要求、试验方法、检验规则以及标志、包装、运输和贮存等。本标准适用于建筑玻璃及工业玻璃用玻璃釉料。本标准不适用于汽车玻璃用玻璃釉料。

Glass enamel

GSO ASTM C729:2013 用浸浮比较器测定玻璃密度的标准试验方法

1.1 This test method covers the determination of the density of glass or nonporous solids of density from 1.1 to 3.3 g/cm 3. It can be used to determine the apparent density of ceramics or solids, preferably of known porosity. 1.2 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Test Method for Density of Glass by the Sink – Float Comparator

GSO ISO 10629:2013 原始光学玻璃 50°C 下对含有碱性磷酸盐的水性清洁溶液的耐损伤性 分类和测试方法

This International Standard specifies a method for testing the resistance of raw optical glasses to attack by aqueous alkaline solutions at 50 “C and a classification of optical glasses according to the aqueous alkaline resistance (alkali resistance) determined by this method. This International Standard is applicable to samples of raw optical glasses.

Raw optical glass -- Resistance to attack by aqueous alkaline solutions at 50 degrees C -- Test method and classification

DB42/T 863-2012 红外光学玻璃

Infrared Optical Glass

ASTM C965-96(2012) 在软化点以上测量玻璃粘度的标准实施规程

1.1 This practice covers the determination of the viscosity of glass above the softening point through the use of a platinum alloy spindle immersed in a crucible of molten glass. Spindle torque, developed by differential angular velocity between crucible and spindle, is measured and used to calculate viscosity. Generally, data are taken as a function of temperature to describe the viscosity curve for the glass, usually in the range from 1 to 106 Pa·s. 1.2 Two procedures with comparable precision and accuracy are described and differ in the manner for developing spindle torque. Procedure A employs a stationary crucible and a rotated spindle. Procedure B uses a rotating crucible in combination with a fixed spindle. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Practice for Measuring Viscosity of Glass Above the Softening Point

JC/T 2072-2011 中空玻璃用干燥剂

本标准规定了中空玻璃用干燥剂的术语和定义、分类和规格、要求、试验方法、检验规则以及标志、包装、运输和贮存。 本标准适用于吸附中空玻璃间隔层中水分的干燥材料。

Desiccant for insulating glass units

GSO 2187:2011 玻璃软化点测试方法

This test method covers the determination of the softening point of a glass by determining the temperature at which a round fiber of the glass, nominally 0.65 mm in diameter and 235 mm long with specified tolerances, elongates under its own weight at a rate of 1 mm/min when the upper 100 mm of its length is heated in a specified furnace at the rate of 5 ± 1°C/min. 1.2 This method is applicable to all glasses of normal bulk-production composition unless devitrification takes place during the preparation of the specimen. 1.3 The values stated in SI units are to be in this standard. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Glass -Test Method for Softening Point

DIN ISO 12123:2011 光学和光子学.未加工的光学玻璃规范(ISO 12123-2010)

Optics and photonics - Specification of raw optical glass (ISO 12123:2010)

GSO ASTM C336:2011 用纤维伸长率测定玻璃塑化点和应力点的标准测试方法

1.1 This test method covers the determination of the annealing point and the strain point of a glass by measuring the viscous elongation rate of a fiber of the glass under prescribed condition. 1.2 The annealing and strain points shall be obtained by following the specified procedure after calibration of the apparatus using fibers of standard glasses having known annealing and strain points, such as those specified and certified by the National Institute of Standards and Technology (NIST)2 (see Appendix X1). 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Test Method for Annealing Point and Strain Point of Glass by Fiber Elongation

ASTM C1720-11 固化废料玻璃和仿废料玻璃的液态温度测定的标准试验方法

This procedure can be used for (but is limited to) the following applications: (1) support glass formulation development to make sure that processing criteria are met, (2) support production (for example, processing or troubleshooting), and (3) support model validation.1.1 These practices cover procedures for determining the liquidus temperature (TL) of nuclear waste, mixed nuclear waste, simulated nuclear waste, or hazardous waste glass in the temperature range from 600°C to 1600°C. This method differs from Practice C829 in that it employs additional methods to determine TL. TL is useful in waste glass plant operation, glass formulation, and melter design to determine the minimum temperature that must be maintained in a waste glass melt to make sure that crystallization does not occur or is below a particular constraint, for example, 1 volume % crystallinity or T1%. As of now, many institutions studying waste and simulated waste vitrification are not in agreement regarding this constraint (1). 1.2 Three methods are included, differing in (1) the type of equipment available to the analyst (that is, type of furnace and characterization equipment), (2) the quantity of glass available to the analyst, (3) the precision and accuracy desired for the measurement, and (4) candidate glass properties. The glass properties, for example, glass volatility and estimated TL, will dictate the required method for making the most precise measurement. The three different approaches to measuring TL described here include the following: (A) Gradient Temperature Furnace Method (GT), (B) Uniform Temperature Furnace Method (UT), and (C) Crystal Fraction Extrapolation Method (CF). This procedure is intended to provide specific work processes, but may be supplemented by test instructions as deemed appropriate by the project manager or principle investigator. The methods defined here are not applicable to glasses that form multiple immiscible liquid phases. Immiscibility may be detected in the initial examination of glass during sample preparation (see 9.3). However, immiscibility may not become apparent until after testing is underway. 1.3 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Test Method for Determining Liquidus Temperature of Immobilized Waste Glasses and Simulated Waste Glasses

ASTM C1720-11e1 测定固化废玻璃和模拟废玻璃液相线温度的标准试验方法

5.1 This procedure can be used for (but is limited to) the following applications: (1) support glass formulation development to make sure that processing criteria are met, (2) support production (for example, processing or troubleshooting), and (3) support model validation. 1.1 These practices cover procedures for determining the liquidus temperature (TL) of nuclear waste, mixed nuclear waste, simulated nuclear waste, or hazardous waste glass in the temperature range from 600°C to 1600°C. This method differs from Practice C829 in that it employs additional methods to determine TL. TL is useful in waste glass plant operation, glass formulation, and melter design to determine the minimum temperature that must be maintained in a waste glass melt to make sure that crystallization does not occur or is below a particular constraint, for example, 1 volume % crystallinity or T1%. As of now, many institutions studying waste and simulated waste vitrification are not in agreement regarding this constraint (1). 1.2 Three methods are included, differing in (1) the type of equipment available to the analyst (that is, type of furnace and characterization equipment), (2) the quantity of glass available to the analyst, (3) the precision and accuracy desired for the measurement, and (4) candidate glass properties. The glass properties, for example, glass volatility and estimated TL, will dictate the required method for making the most precise measurement. The three different approaches to measuring TL described here include the following: (A) Gradient Temperature Furnace Method (GT), (B) Uniform Temperature Furnace Method (UT), and (C) Crystal Fraction Extrapolation Method (CF). This procedure is intended to provide specific work processes, but may be supplemented by test instructions as deemed approp......

Standard Test Method for Determining Liquidus Temperature of Immobilized Waste Glasses and Simulated Waste Glasses

NF S10-019:2010 光学和电子学.未加工的光学玻璃规范

Optics and photonics - Specification of raw optical glass.

ISO 12123:2010 光学和电子学.生光学玻璃规范

This International Standard gives rules for the specification of raw optical glass. It serves as a complement to ISO 10110, which provides rules specifying finished optical elements. Since raw optical glass may be quite different in shape and size from the optical elements, its specification also differs from that of optical elements. This International Standard provides guidelines for the essential specification characteristics of raw optical glass in order to improve communication between glass suppliers and optical element manufacturers. For specific applications (e.g. lasers, the infrared spectral range), specifications based on this International Standard will have to be supplemented.

Optics and photonics - Specification of raw optical glass

ASTM C146-94a(2009) 玻璃砂化学分析标准试验方法

Standard Test Methods for Chemical Analysis of Glass Sand