81.080 耐火材料 标准查询与下载

ASTM C456-18(2023) 基本砖和型材抗水化性的标准试验方法

Standard Test Method for Hydration Resistance of Basic Bricks and Shapes

T/CSTM 01064-2023 耐火陶瓷纤维模块

本文件规定了耐火陶瓷纤维模块的术语和定义、分类、牌号、标记、技术要求、试验方法、质量评定程序、包装、标志、运输、储存和质量证明书。 本文件适用于高温工业窑炉用的耐火陶瓷纤维模块。

Refractory ceramic fiber modules

T/CSTM 01105-2023 含碳耐火材料抗氧化性试验方法

本文件规定了含碳耐火材料抗氧化性试验方法，包括强度变化率/脱碳层厚度法和氧化失重法两种方法的原理、仪器设备、试样制备、试验步骤、结果评定及试验报告。 本文件适用于含碳耐火材料抗氧化性的测试评定。

Test methods for the oxidation resistance of carbon-containing refractories

T/HEBQIA 191-2023 抗热震隔热耐火砖

本文件规定了抗热震隔热耐火砖的分类、形状和尺寸、技术要求、实验方法、质量评定程序、包装、标志、运输、储存及质量证明书。

Thermal shock resistant refractory bricks

T/CSTM 01106-2023 烧结高纯铝镁尖晶石

本文件规定了烧结高纯铝镁尖晶石的术语和定义、牌号、技术要求、试验方法、质量评定程序、包装、标志、运输、储存和质量证明书。 本文件适用于烧结法生产的高纯铝镁尖晶石。

Sintered high-purity aluminate magnesium spinel

T/CACE 098-2023 再生二氧化锆

1 范围 2 规范性引用文件 3 术语和定义 4 牌号 5 技术要求 6 试验方法 7 检验规则 8 标志、包装、运输和贮存 9 质量证明书 参考文献

Recycled zirconia

T/HEBQIA 187-2023 高炉用模压炭砖

本文件规定了高炉用模压炭砖的代号、技术要求、试验方法、检验规则及标志、包装、运输、贮存和质量证明书。

Molded carbon bricks for blast furnace

ASTM C987-10(2023) 炉上部结构耐火材料蒸气侵蚀的标准试验方法

1.1  This test method covers a procedure for comparing the behavior of refractories in contact with vapors under conditions intended to simulate the environment within a glass-melting or other type of furnace when refractories are exposed to vapors from raw batch, molten glass, fuel, fuel contaminants, or other sources. This procedure is intended to accelerate service conditions for the purpose of determining in a relatively short time the interval resistance to fluxing, bloating, shrinkage, expansion, mineral conversion, disintegration, or other physical changes that may occur. 1.2  The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.3  This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.4  This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Method for Vapor Attack on Refractories for Furnace Superstructures

ASTM C1223-19(2023) AZS 熔铸耐火材料玻璃渗出物测试的标准测试方法

1.1  This test method covers a procedure for causing the exudation of a glassy phase to the surface of fusion-cast specimens by subjecting them to temperatures corresponding to glass furnace operating temperatures. 1.2  This test method covers a procedure for measuring the exudate as the percent of volume increase of the specimen after cooling. 1.3  Units— The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.3.1  Exception— The balance required for this test method uses only SI units (Section 7 ). 1.4  This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.5  This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Method for Testing of Glass Exudation from AZS Fusion-Cast Refractories

ASTM C134-95(2023) 耐火砖和隔热耐火砖的尺寸、尺寸测量和堆积密度的标准测试方法

1.1  These test methods cover procedures for measuring size, dimensional measurement, bulk density, warpage, and squareness of rectangular dense refractory brick and rectangular insulating firebrick. More precise determination of bulk density of refractory brick can be made by Test Methods C20 . Stack height is generally determined only for dense refractories. Note 1:  Test Methods C830 and Test Method C914 are also used to determine bulk density of refractory brick, by different procedures. 1.2  The test methods appear in the following order:   Sections Size and Bulk Density 4 through 7 Warpage of Refractory Brick  8 through 10 Squareness of Refractory Brick 11 through 14 1.3  The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.4  This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.5  This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Methods for Size, Dimensional Measurements, and Bulk Density of Refractory Brick and Insulating Firebrick

ASTM C830-00(2023) 通过真空压力测定耐火材料的表观孔隙率、液体吸收率、表观比重和堆积密度的标准测试方法

1.1  These test methods cover the determination of the following properties of refractory shapes: 1.1.1  Apparent porosity, 1.1.2  Liquid absorption, 1.1.3  Apparent specific gravity, and 1.1.4  Bulk density. 1.2  These test methods are applicable to all refractory shapes except those that chemically react with both water and mineral spirits. When testing a material capable of hydration or other chemical reaction with water but which does not chemically react with mineral spirits, mineral spirits is substituted for water and appropriate corrections for the density differences are applied when making calculations. 1.3  Units— The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.3.1  Exception— The apparatus used in this standard is only available in SI units. 1.4  This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. Note 1:  Test Methods C20 cover procedures for testing properties of refractories that are not attacked by water. 1.5  This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Methods for Apparent Porosity, Liquid Absorption, Apparent Specific Gravity, and Bulk Density of Refractory Shapes by Vacuum Pressure

ASTM C604-18(2023) 用气体比较比重瓶测定耐火材料真实比重的标准测试方法

1.1  This test method covers the determination of the true specific gravity of solid materials, and is particularly useful for materials that easily hydrate which are not suitable for test with Test Method C135 . This test method may be used as an alternate for Test Methods C135 , C128 , and C188 for determining true specific gravity. 1.2  Units— The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.2.1  Exception— In 7.3 , the equivalent SI unit is expressed in parentheses. 1.3  This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.4  This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Method for True Specific Gravity of Refractory Materials by Gas-Comparison Pycnometer

YB/T 116-2023 炉辊用耐火浇注料

本文件规定了炉辊用耐火浇注料的术语和定义、分类和牌号、技术要求、试验方法、质量评定程序、包装、标志、运输、储存和 质量证明书。本文件适用于辊底炉炉辊用耐火浇注料。

Refractory castables for furnace rollers

YB/T 4193-2023 抗结皮耐火浇注料

本文件规定了抗结皮耐火浇注料的术语和定义、牌号、技术要求、试验方法、质量评定程序、包装、标志、运输、储存和质量证 明书。本文件适用于新型干法水泥窑使用的抗结皮耐火浇注料。

Anti-scaling refractory castable

YB/T 6113-2023 电加热炉碳化硅导热体

本文件规定了电加热炉碳化硅导热体的术语和定义、牌号、技术要求、试验方法、质量评定程序、包装、标志、运输、储存和质 量证明书。本文件主要适用于电加热炉导热体为碳化硅的制品。

Silicon carbide thermal conductor for electric heating furnace

YB/T 4129-2023 塑性相复合刚玉砖

本文件规定了塑性相复合刚玉砖的术语和定义、牌号、技术要求、试验方法、质量评定程序、包装、标志、运输和质量证明书。本文件主要适用于砌筑高炉炉缸、炉底内衬用砖。

Plastic phase composite corundum brick

YB/T 4126-2023 高炉出铁沟浇注料

本文件规定了高炉出铁沟浇注料的术语和定义、牌号、技术要求、试验方法、质量评定程序、包装、标志、运输、储存和质量证 明书。本文件适用于高炉主沟、铁沟、渣沟和摆动流槽等部位的工作 层耐火浇注料（含预制件）以及热修补用喷涂料。

Blast furnace tap trough castables

23/30446952 DC BS EN ISO 21068-1 含有碳化硅、氮化硅、氮氧化硅和塞隆的原材料和耐火制品的化学分析 第1部分：一般信息和样品制备

BS EN ISO 21068-1. Chemical analysis of raw materials and refractory products containing silicon carbide, silicon nitride, silicon oxynitride and sialon - Part 1. General information and sample preparation

23/30446956 DC BS EN ISO 21068-2 含有碳化硅、氮化硅、氮氧化硅和塞隆的原材料和耐火制品的化学分析第2部分 挥发性成分、总碳、游离碳、碳化硅等的测定

BS EN ISO 21068-2. Chemical analysis of raw materials and refractory products containing silicon carbide, silicon nitride, silicon oxynitride and sialon - Part 2. Determination of volatile components, total carbon, free carbon, silicon carbide,…

23/30446996 DC BS EN ISO 21068-4 含有碳化硅、氮化硅、氮氧化硅和塞隆的原材料和耐火制品的化学分析第4部分：X射线衍射方法

BS EN ISO 21068-4. Chemical analysis of raw materials and refractory products containing silicon carbide, silicon nitride, silicon oxynitride and sialon - Part 4. XRD methods