83.040.20 橡胶合成配料 标准查询与下载

HG/T 5835-2021 硫化促进剂 双[O-丁基-O-（2－乙基己基）二硫代磷酸]锌 ( ZEHBP)

Vulcanization accelerator bis[O-butyl-O-(2-ethylhexyl)dithiophosphate]zinc (ZEHBP)

T/CCOA 15-2020 稻壳白炭黑

本文件规定了稻壳白炭黑的分类、技术要求、检验方法、检验规则、标签、标志、包装、贮存、运输和保质期。 本文件适用于以稻壳为原料制得的橡胶工业用稻壳白炭黑。

Rice husk silica

HG/T 5807-2020 硅橡胶用炭黑色浆

Carbon black paste for silicone rubber

HG/T 3061-2020 橡胶配合剂 沉淀水合二氧化硅

Rubber compounding agent precipitated hydrated silica

HG/T 5810-2020 橡胶配合剂 天然隐晶质石墨材料

Rubber compounding agent natural cryptocrystalline graphite material

HG/T 2404-2020 橡胶配合剂 沉淀水合二氧化硅在丁苯橡胶中的鉴定

Identification of rubber compounding agent precipitated hydrated silica in styrene-butadiene rubber

ASTM D8371-20 炭黑中痕量金属含量分析的标准试验方法

1.1 This test method covers the determination of metal content in carbon black with ICP-OES or ICP-MS after adequate digestion. See 3.1.5 – 3.1.7 for definitions. 1.2 The concentration ranges covered by these test methods are determined by the sensitivity of the instruments, the amount of sample taken for analysis and the dilution volume. 1.3 Detection limits, sensitivity and optimum ranges of the metals will vary with the matrices and model of spectrometer. 1.4 Elements present at concentrations above the linear response range of the calibration curve can be determined with additional appropriate dilutions. 1.5 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.6 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.7 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Method for Trace Metal Content Analysis in Carbon Black

ASTM D3493-20 压缩样品（COAN）炭黑吸油量的标准试验方法

Standard Test Method for Carbon Black—Oil Absorption Number of Compressed Sample (COAN)

T/CACE 021-2020 橡胶用改性裂解炭黑

1    范围 2　规范性引用文件 3　术语和定义 4　命名方法 5　技术要求 6    检验和判定 7　标识、包装、运输、贮存

Modified pyrolysis carbon black for use in rubber products

T/SDQE 020-2020 泰山品质 橡胶防老剂 N-1,3-二甲基丁基 -N’-苯基对苯二胺（6PPD）

本文件规定了泰山品质橡胶防老剂 N-1,3-二甲基丁基-N'-苯基对苯二胺（以下简称“橡胶防老剂6PPD”）的技术要求、试验方法、检验规则、标志、包装、运输和贮存。由4-氨基二苯胺与甲基异丁基甲酮在催化剂存在下缩合还原而制得的橡胶防老剂6PPD。化学名称：N-1,3-二甲基丁基-N'-苯基对苯二胺分子式： C18H24N2结构式：相对分子质量：268.40 （ 按 2018年国际相对原子质量）CAS RN: 793-24-8

Taishan quality rubber antioxidant N-1,3-dimethylbutyl-N'-phenyl-p-phenylenediamine (6PPD)

ASTM D1799-20 炭黑抽样包装装运的标准实施规程

1.1 This practice covers the sampling of packaged carbon blacks for shipment in bags, cartons, flexible intermediate bulk containers (FIBC), or other non-bulk packages. NOTE 1—The tests to be made on the samples obtained by this practice shall be determined by the producer and the consumer. The specific details of each test method are described in appropriate ASTM methods used for testing carbon black. 1.2 The values stated in SI units are to be regarded as the standard. The values in parentheses are for information only. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Practice for Carbon Black—Sampling Packaged Shipments

ASTM D1619-20 炭黑的标准试验方法 - 硫含量

1.1 These test methods cover the determination of the sulfur content of carbon black. The following test methods are included: Sections Test Method A High-Temperature Combustion With Infrared Absorption Detection Procedures 6 to 13 Test Method B X-Ray Fluorescence 14 to 19 1.2 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Methods for Carbon Black—Sulfur Content

ASTM D1514-15(2020) 炭黑 - 筛渣的标准试验方法

1.1 This test method covers the determination of the water wash sieve residue in regular untreated carbon blacks. It may not be applicable to oil-treated carbon blacks because the oil would prevent proper wetting of the black by water. 1.2 The values stated in SI units are to be regarded as the standard. The values in parentheses are for information only. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. For specific precautionary statements, see Section 6. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Method for Carbon Black—Sieve Residue

ASTM D1900-20 炭黑采样散装货物的标准做法

1.1 This practice covers procedures for the sampling and data reporting of bulk shipments of carbon black in threecompartment hopper rail cars and compartmented bulk hopper trailers. NOTE 1—The tests to be made on the samples obtained by this practice, how many samples are taken, where they are taken, and what statistical values (if any) to report shall be determined by agreement between the purchaser and the manufacturer. This practice gives guidance for use in developing such agreements or for use when no formal agreement exists. The specific details of each procedure are described in appropriate ASTM test methods used for testing carbon black. NOTE 2—Some purchasers or manufacturers may consider Flexible Intermediate Bulk Containers (FIBC) to be a bulk shipment. See Practice D1799 for guidance on sampling and reporting for this package. 1.2 The values stated in SI units are to be regarded as standard. The values given in parentheses are for information only. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Practice for Carbon Black—Sampling Bulk Shipments

NF T45-105:2020 橡胶助剂. 炭黑. 用氮吸附法测定比表面积. 单点法

Le présent document spécifie deux méthodes pour la détermination de la surface spécifique des types et qualités de noirs de carbone utilisés dans l'industrie du caoutchouc:- méthode A: méthode par chromatographie en phase gazeuse (méthode du gaz vecteur) automatique;- méthode B:

Rubber compounding ingredients - Carbon black - Determination of specific surface area by nitrogen adsorption methods - Single-point procedures

BS ISO 4652:2020 橡胶配合剂 碳黑 氮气吸附法测定比表面积 单点程序

What is ISO 4652 about?    ISO 4652 discusses rubber compounding ingredients. ISO 4652 specifies two methods for the determination of the specific surface area of types and grades of carbon black for use in the rubber industry:   Method A: automatic gas chromatography method (carrier gas method)   Method B: automatic volumetric method   Somewhat different results might be obtained from the two methods. The de...

Rubber compounding ingredients. Carbon black. Determination of specific surface area by nitrogen adsorption methods. Single-point procedures

SN/T 5249-2020 沉淀水合二氧化硅中铁、锰、铜、铝、钛、铅、铬、钙、镁、锌、钾、钠含量的测定 电感耦合等离子体原子发射光谱法

Determination of iron, manganese, copper, aluminum, titanium, lead, chromium, calcium, magnesium, zinc, potassium and sodium in precipitated hydrated silica by inductively coupled plasma atomic emission spectrometry

T/JMZJXH 004-2020 合成橡胶材料及其制品中胍类硫化促进剂残留量的测定-高效液相色谱法

规定了采用高效液相色谱法测定合成橡胶材料及其制品中1,3-二苯胍（DPG）和1,3-二邻甲苯胍（DOTG）的残留量。

Determination of guanidine vulcanization accelerators residues in synthetic rubber materials and rubber products—High performance liquid chromatography

ISO 4652:2020 橡胶配料 - 炭黑 - 通过氮吸附法测定比表面积 - 单点程序

This document specifies two methods for the determination of the specific surface area of types and grades of carbon black for use in the rubber industry: — method A: automatic gas chromatography method (carrier gas method); — method B: automatic volumetric method. Somewhat different results might be obtained from the two methods. The degassing procedure differs between method A and method B, and it is important to investigate the possibility of correcting the results by using standard reference blacks. The results might also differ from those obtained using the multipoint method specified in ISO 18852, which is the preferred method. These methods are not applicable to porous carbon blacks.

Rubber compounding ingredients — Carbon black — Determination of specific surface area by nitrogen adsorption methods — Single-point procedures

ASTM D6746-15(2020) 用于测定生橡胶或未硫化化合物的绿色强度和应力松弛的标准测试方法

1.1 This test method covers methods to evaluate a characteristic of raw rubber or unvulcanized rubber compounds that is designated as green strength. This special strength property for uncured rubbers is an important processing performance attribute in rubber product manufacturing. 1.2 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Method for Determination of Green Strength and Stress Relaxation of Raw Rubber or Unvulcanized Compounds