83.040.20 橡胶合成配料 标准查询与下载

ASTM D4583-95(2019) 炭黑的标准实施规程&x2014；通过分析过程控制数据计算过程指标

Standard Practice for Carbon Black—Calculation of Process Indexes From an Analysis of Process Control Data

ASTM D1900-19 炭黑的标准实施规程&x2014；散装货物抽样

Standard Practice for Carbon Black—Sampling Bulk Shipments

ISO 20927:2019 橡胶配料 沉淀二氧化硅 圆盘离心机测定骨料粒径分布

This document specifies a general method for determining the aggregate size distribution (ASD) of silica by using a disc centrifuge according to the principle of sedimentation. As pre-stage the silica is de-agglomerated in water using strong ultrasonic power treatment. The method is used for precipitated silica.

Rubber compounding ingredients — Precipitated silica — Determination of aggregate size distribution by disc centrifuge

ASTM D1510-19a 炭黑的标准试验方法&x2014；碘吸附数

Standard Test Method for Carbon Black—Iodine Adsorption Number

ASTM D3265-19a 炭黑的标准试验方法&x2014；着色强度

Standard Test Method for Carbon Black—Tint Strength

ASTM D3493-19 炭黑的标准试验方法&x2014；压缩样品吸油量（COAN）

Standard Test Method for Carbon Black—Oil Absorption Number of Compressed Sample (COAN)

ASTM D4821-19 炭黑标准指南&x2014；试验方法精密度和偏差的验证

Standard Guide for Carbon Black—Validation of Test Method Precision and Bias

JIS K 6217-6:2019 橡胶工业用炭黑. 基本特性. 第6部分: 用盘式离心沉淀摄影法测定集料粒度分布

Carbon black for rubber industry -- Fundamental characteristics -- Part 6: Determination of aggregate size distribution by disc centrifuge photosedimentometry

ASTM D3265-19 炭黑的标准试验方法&x2014；着色强度

Standard Test Method for Carbon Black—Tint Strength

ASTM D2663-14(2019) 炭黑的标准试验方法&x2014；橡胶中的分散

Standard Test Methods for Carbon Black—Dispersion in Rubber

ASTM D3192-09(2019) 天然橡胶中炭黑评定的标准试验方法

1.1 These test methods cover the standard materials, test formulation, mixing procedure, and test methods for the evaluation and production control of carbon blacks in natural rubber (NR). 1.2 The values stated in SI units are to be regarded as the standard. The values in parentheses are for information only. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Methods for Carbon Black Evaluation in NR (Natural Rubber)

ASTM D7558-09(2019) 天然胶乳和丁腈手套中可萃取化学二烷基二硫代氨基甲酸酯、硫脲和巯基苯并噻唑促进剂定量的比色/分光光度法的标准试验方法

1.1 This test method is designed to quantify the amount of total extractable accelerators in natural rubber latex (NRL) and nitrile gloves. Three common classes of rubber accelerators, the mercaptobenzothiazole (MBT), thiuram, and thiocarbamate type compounds can be detected and quantified by this method. If the specific rubber accelerator(s) present in the glove material is not known, quantification is based on zinc dibutyldithiocarbamate (ZDBC) equivalents. This method will not detect all potential rubber accelerators, including mercaptobenzothiazole disulfide, dimorpholine, thioureas and diphenyl diamine. 1.2 For the purpose of this test method, the range of chemical accelerator measurement is based on the limit of detection (LOD) established in the performing laboratory. 1.3 This test method should be performed by experienced analysts or under the supervision of those experienced in the use of spectroscopy and working with organic solvents. 1.4 This test method has not been validated for measurement of long chain dithiocarbamates or accelerators from other rubber products, such as lubricated condoms (1).2 Although this assay has been reported in the literature for the evaluation of accelerator levels in condoms, further validation for accelerator measurement from other rubber products is required by the testing laboratory prior to use. 1.5 This test method is not designed to evaluate the potential of rubber materials to induce or elicit Type IV skin sensitization reactions (for Type IV skin sensitization reactions see Test Method D6355). Total extractable accelerator content does not reflect bioavailablity of individual accelerators that are detected and measured by this method. This test method should be used to test and measure the total residual chemical accelerator level in NRL and nitrile gloves under controlled laboratory conditions, and should not be used to describe, appraise, or assess the hazard or risk of these materials or products under actual in-use conditions. 1.6 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.7 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.8 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Method for Colorimetric/Spectrophotometric Procedure to Quantify Extractable Chemical Dialkyldithiocarbamate, Thiuram, and Mercaptobenzothiazole Accelerators in Natural Rubber Latex and

ASTM D2663-14(2019)e1 橡胶中炭黑分散性的标准试验方法

1.1 These test methods cover the degree of dispersion of carbon black in rubber. Four test methods are described as follows: Sections Test Method A—Visual Inspection 3 – 11 Test Method B—Agglomerate Count 12 – 22 Test Method C—Microroughness Measurement with Profilometer 23 – 33 Test Method D—Microroughness Measurement with IFM 34 – 42 1.2 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Methods for Carbon Black—Dispersion in Rubber

ASTM D1519-95(2019) 橡胶化学品的标准试验方法&x2014；熔化范围的测定

1.1 These test methods cover the determination of the melting range of commercial rubber processing chemicals either by use of capillary melting point tubes or by differential scanning calorimetry (DSC). 1.2 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Methods for Rubber Chemicals—Determination of Melting Range

ASTM D6370-99(2019) 橡胶的标准试验方法&x2014；通过热重分析（TGA）进行成分分析

1.1 This test method provides a thermogravimetric (TGA) technique to determine the amounts of organics (oil, polymer), carbon black and ash (filler) in a rubber compound. 1.2 The amount of plasticizer/oil may be determined separately using Test Method D297. 1.3 This test method utilizes previously calibrated, manual or computer assisted TGA instrumentation. 1.4 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Method for Rubber—Compositional Analysis by Thermogravimetry (TGA)

ASTM D1510-19 炭黑的标准试验方法&x2014；碘吸附数

Standard Test Method for Carbon Black—Iodine Adsorption Number

ASTM D3265-19b 炭黑的标准试验方法&8212；着色强度

1.1 This test method covers the determination of the tint strength of carbon black relative to an industry tint reference black (ITRB). 1.2 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Method for Carbon Black—Tint Strength

ASTM D2007-19 用粘土测定橡胶填充剂、加工油和其他石油衍生油中特征基团的标准试验方法&8212；凝胶吸收色谱法

1.1 This test method covers a procedure for classifying oil samples of initial boiling point of at least 260 °C (500 °F) into the hydrocarbon types of polar compounds, aromatics and saturates, and recovery of representative fractions of these types. This classification is used for specification purposes in rubber extender and processing oils. NOTE 1—See Test Method D2226. 1.2 This test method is not directly applicable to oils of greater than 0.1 % by mass pentane insolubles. Such oils can be analyzed after removal of these materials, but precision is degraded (see Appendix X1). 1.3 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. Specific warning statements are given in 6.1, Section 7, A1.4.1, and A1.5.5. 1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Method for Characteristic Groups in Rubber Extender and Processing Oils and Other Petroleum-Derived Oils by the Clay—Gel Absorption Chromatographic Method

KS M 6539-2018(2023) 橡胶配合料硫试验方法

Rubber compounding ingredients — Sulfur — Methods of test

KS M 6539-2018 橡胶复合成分 - 硫 - 测试方法

Rubber compounding ingredients — Sulfur — Methods of test