83.080.10 热固性塑料 标准查询与下载

GSO ISO 14526-3:2014 塑料 粉末成型酚醛化合物 (PF-PMCS) 第3部分：选择研磨化合物的要求

This part of ISO 14526 specifies the requirements for the physical and chemical properties of phenolic powder moulding compounds (PF-PMCs) and compression- or injection-moulded test specimens produced from them. It is limited to those powder moulding compounds whose composition and properties are significantly different. It is further limited to those moulding compounds which are of general technical and/or economic importance. The properties which are used to characterize the moulding compounds, the test methods and the test conditions are selected from those given in ISO 14526-2. The moulding compounds are divided into types according to their composition and properties. The various types are designated using the designation system defined in ISO 14526-1.

Plastics -- Phenolic powder moulding compounds (PF-PMCs) -- Part 3: Requirements for selected moulding compounds

GSO ISO 14529-1:2014 塑料 三聚氰胺/酚醛粉末模塑料 (MP-PMC) 第1部分：命名系统和规格基础

1.1 This part of ISO 14529 establishes a data block system for the designation of melamine/phenolic powder moulding compounds (MP-PMCs). 1.2 The various types of MP-PMC are differentiated from each other by a classification system based on information about the filler/reinforcement type and content, the intended method of processing, any special properties and those of the special properties used specifically for designation purposes (designatory properties). 1.3 This part of ISO 14529 is applicable to all MP-PMCs ready for normal use in the form of powder, granules or ground material. 1.4 It is not intended to imply that materials having the same designation necessarily give the same performance. This part of ISO 14529 does not provide engineering data, performance data or data on processing conditions which may be required to specify a material for a particular application and/or method of processing. If such additional properties are required, they shall be determined in accordance with the test methods specified in ISO 14529-2, if suitable. 1.5 Whenever general requirement data, as covered by ISO 14529-3, need to be indicated, this is also done using this data block system. 1.6 To ensure that code-letters and code-numbers remain unambiguous, and to avoid conflicts within the system, any new code-letters or code-numbers for use in data block 1, 2 or 3 shall be approved before use by the secretariats of ISO/ТС 61/SC 1, SC 12 and SC 13.

Plastics -- Melamine/phenolic powder moulding compounds (MP-PMCs) -- Part 1: Designation system and basis for specifications

GSO ISO 14528-3:2014 塑料 脲醛化合物 (PF-PMCS) 的粉末成型 第3部分：研磨化合物的选择要求

This part of ISO 14528 specifies the requirements for the physical and chemical properties of melamine-formaldehyde powder moulding compounds (MF-PMCs) and compression- or injection-moulded test specimens produced from them. It is limited to those powder moulding compounds whose composition and properties are significantly different. It is further limited to those moulding compounds which are of general technical and/or economic importance. The properties which are used to characterize the moulding compounds, the test methods and the test conditions are selected from those given in ISO 14528-2. The moulding compounds are divided into types according to their composition and properties. The various types are designated using the designation system defined in ISO 14528-1

Plastics -- Melamine-formaldehyde powder moulding compounds (MF-PMCs) -- Part 3: Requirements for selected moulding compounds

GSO ISO 14526-2:2014 塑料 酚醛粉末模塑料 (PF-PMC) 第2部分：测试样品的制备和性能测定

This part of ISO 14526 specifies the methods of preparation of test specimens and the test methods to be used in determining the properties of phenolic powder moulding compounds (PF-PMCs). Requirements for handling test material and for conditioning both the test material before moulding and the specimens before testing are given here. Procedures and conditions for the preparation of test specimens and procedures for measuring properties of the materials from which these specimens are made are given. Properties and test methods which are suitable and necessary to characterize PMCs are listed. The properties have been selected from the general test methods in ISO 10350-1. Other test methods in wide use for, or of particular significance to, PMCs are also included in this part of ISO 14526, as are the designatory properties found in ISO 14526-1. In order to obtain reproducible and comparable test results, it is necessary to use the methods of preparation and conditioning, the specimen dimensions and the test procedures specified herein. Values determined will not necessarily be identical to those obtained using specimens of different dimensions or prepared using different procedures.This part of ISO 14526 specifies the methods of preparation of test specimens and the test methods to be used in determining the properties of phenolic powder moulding compounds (PF-PMCs). Requirements for handling test material and for conditioning both the test material before moulding and the specimens before testing are given here. Procedures and conditions for the preparation of test specimens and procedures for measuring properties of the materials from which these specimens are made are given. Properties and test methods which are suitable and necessary to characterize PMCs are listed. The properties have been selected from the general test methods in ISO 10350-1. Other test methods in wide use for, or of particular significance to, PMCs are also included in this part of ISO 14526, as are the designatory properties found in ISO 14526-1. In order to obtain reproducible and comparable test results, it is necessary to use the methods of preparation and conditioning, the specimen dimensions and the test procedures specified herein. Values determined will not necessarily be identical to those obtained using specimens of different dimensions or prepared using different procedures.

Plastics -- Phenolic powder moulding compounds (PF-PMCs) -- Part 2: Preparation of test specimens and determination of properties

GSO ISO 14530-1:2014 塑料 不饱和聚酯粉末复合材料（UP-PMC）的形成 第1部分：标记系统和规格基础

1.1 This part of ISO 14530 establishes a data block system for the designation of unsaturated-polyester powder moulding compounds (UP-PMCs). 1.2 The various types of UP-PMC are differentiated from each other by a classification system based on information about the filler/reinforcement type and content, the intended method of processing, any special properties and those of the special properties used specifically for designation purposes (designatory properties). 1.3 This part of ISO 14530 is applicable to all UP-PMCs ready for normal use in the form of powder, granules or ground material. 1.4 It is not intended to imply that materials having the same designation necessarily give the same performance. This part of ISO 14530 does not provide engineering data, performance data or data on processing conditions which may be required to specify a material for a particular application and/or method of processing. If such additional properties are required, they shall be determined in accordance with the test methods specified in ISO 14530-2, if suitable. 1.5 Whenever general requirement data, as covered by ISO 14530-3, need to be indicated, this is also done using this data block system. 1.6 To ensure that code-letters and code-numbers remain unambiguous, and to avoid conflicts within the system, any new code-letters or code-numbers for use in data block 1, 2 or 3 shall be approved before use by the secretariats of ISO/ТС 61/SC 1, SC 12 and SC 13.

Plastics -- Unsaturated-polyester powder moulding compounds (UP-PMCs) -- Part 1: Designation system and basis for specifications

GSO ISO 14530-2:2014 塑料 不饱和聚酯粉末复合材料（UP-PMC）的形成 第2部分：测试样品的制备和性能测定

This part of ISO 14530 specifies the methods of preparation of test specimens and the test methods to be used in determining the properties of unsaturated-polyester powder moulding compounds (UP-PMCs). Requirements for handling test material and for conditioning both the test material before moulding and the specimens before testing are given here. Procedures and conditions for the preparation of test specimens and procedures for measuring properties of the materials from which these specimens are made are given. Properties and test methods which are suitable and necessary to characterize PMCs are listed. The properties have been selected from the general test methods in ISO 10350-1. Other test methods in wide use for, or of particular significance to, PMCs are also included in this part of ISO 14530, as are the designatory properties found in ISO 14530-1. In order to obtain reproducible and comparable test results, it is necessary to use the methods of preparation and conditioning, the specimen dimensions and the test procedures specified herein. Values determined will not necessarily be identical to those obtained using specimens of different dimensions or prepared using different procedures.

Plastics -- Unsaturated-polyester powder moulding compounds (UP-PMCs) -- Part 2: Preparation of test specimens and determination of properties

GSO ISO 14527-3:2014 塑料 脲醛和脲/三聚氰胺甲醛粉末模塑料（UF-和 UF/MF-PMC） 第3部分：所选模塑料的要求

This part of ISO 14527 specifies the requirements for the physical and chemical properties of urea-formaldehyde and urea/melamine-formaldehyde powder moulding compounds (UF- and UF/MF-PMCs) and compression- or injection-moulded test specimens produced from them. It is limited to those powder moulding compounds whose composition and properties are significantly different. It is further limited to those moulding compounds which are of general technical and/or economic importance. The properties which are used to characterize the moulding compounds, the test methods and the test conditions are selected from those given in ISO 14527-2. The moulding compounds are divided into types according to their composition and properties. The various types are designated using the designation system defined in ISO 14527-1.

Plastics -- Urea-formaldehyde and urea/melamine-formaldehyde powder moulding compounds (UF- and UF/MF-PMCs) -- Part 3: Requirements for selected moulding compounds

GSO ISO 18280:2014 塑料 环氧树脂 测试方法

Epoxy resins are a family of synthetic resins, including products, which range from viscous liquids to high-melting solids. The resin molecule contains as reactive sites one or more oxirane or epoxy groups, usually in the form of a glycidyl group. The most commercially important resin is the glycidyl ether of bisphenol A, produced by the condensation of epichlorohydrin and diphenylpropane (bisphenol A). Epoxy resins with different characteristics are also produced commercially by reacting epichlorohydrin with other materials. To be of use, the resins must be crosslinked with a curing agent or hardener. The choice of curing agent is of importance in designing an epoxy resin system for a given application. The major reactive groups in the resin, the epoxy and the hydroxyl groups, react with many other groups so that many types of chemical substance can be used as curing agents. These include acid anhydrides, aliphatic and aromatic amines and polyaminoamides. Some curing agents will crosslink the resin at ambient temperatures while others require the application of heat. This International Standard provides an overview of the ISO test methods used to characterize epoxy resins. The listed property to be determined in any given case depends on agreement between the supplier and customer.

Plastics -- Epoxy resins -- Test methods

GSO ISO 14526-1:2014 塑料 粉末成型酚醛化合物 (PF-PMCS) 第1部分：鉴别系统和规格基础

1.1 This part of ISO 14526 establishes a data block system for the designation of phenolic powder moulding compounds (PF-PMCs). 1.2 The various types of PF-PMC are differentiated from each other by a classification system based on information about the filler/reinforcement type and content, the intended method of processing, any special properties and those of the special properties used specifically for designation purposes (designatory properties). 1.3 This part of ISO 14526 is applicable to all PF-PMCs ready for normal use in the form of powder, granules or ground material. 1.4 It is not intended to imply that materials having the same designation necessarily give the same performance. This part of ISO 14526 does not provide engineering data, performance data or data on processing conditions which may be required to specify a material for a particular application and/or method of processing. If such additional properties are required, they shall be determined in accordance with the test methods specified in ISO 14526-2, if suitable. 1.5 Whenever general requirement data, as covered by ISO 14526-3, need to be indicated, this is also done using this data block system. 1.6 To ensure that code-letters and code-numbers remain unambiguous, and to avoid conflicts within the system, any new code-letters or code-numbers for use in data block 1, 2 or 3 shall be approved before use by the secretariats of ISO/ТС 61/SC 1, SC 12 and SC 13

Plastics -- Phenolic powder moulding compounds (PF-PMCs) -- Part 1: Designation system and basis for specifications

GSO ISO 14528-2:2014 塑料 脲醛化合物 (PF-PMCS) 的粉末形成 第2部分：测试样品的制备和性能测定

This part of ISO 14528 specifies the methods of preparation of test specimens and the test methods to be used in determining the properties of powder moulding compounds (PMCs). Requirements for handling test material and for conditioning both the test material before moulding and the specimens before testing are given here. Procedures and conditions for the preparation of test specimens and procedures for measuring properties of the materials from which these specimens are made are given. Properties and test methods which are suitable and necessary to characterize PMCs are listed. The properties have been selected from the general test methods in ISO 10350-1. Other test methods in wide use for, or of particular significance to, PMCs are also included in this part of ISO 14528, as are the designatory properties found in ISO 14528-1. In order to obtain reproducible and comparable test results, it is necessary to use the methods of preparation and conditioning, the specimen dimensions and the test procedures specified herein. Values determined will not necessarily be identical to those obtained using specimens of different dimensions or prepared using different procedures.

Plastics -- Melamine-formaldehyde powder moulding compounds (MF-PMCs) -- Part 2: Preparation of test specimens and determination of properties

GSO ISO 14528-1:2014 塑料 三聚氰胺甲醛粉末模塑料（MF-PMC） 第1部分：命名系统和规格基础

1.1 This part of ISO 14528 establishes a data block system for the designation of melamine-formaldehyde powder moulding compounds (MF-PMCs). 1.2 The various types of MF-PMC are differentiated from each other by a classification system based on information about the filler/reinforcement type and content, the intended method of processing, any special properties and those of the special properties used specifically for designation purposes (designatory properties). 1.3 This part of ISO 14528 is applicable to all MF-PMCs ready for normal use in the form of powder, granules or ground material. 1.4 It is not intended to imply that materials having the same designation necessarily give the same performance. This part of ISO 14528 does not provide engineering data, performance data or data on processing conditions which may be required to specify a material for a particular application and/or method of processing. If such additional properties are required, they shall be determined in accordance with the test methods specified in ISO 14528-2, if suitable. 1.5 Whenever general requirement data, as covered by ISO 14528-3, need to be indicated, this is also done using this data block system. 1.6 To ensure that code-letters and code-numbers remain unambiguous, and to avoid conflicts within the system, any new code-letters or code-numbers for use in data block 1, 2 or 3 shall be approved before use by the secretariats of ISO/ТС 61/SC 1, SC 12 and SC 13.

Plastics -- Melamine-formaldehyde powder moulding compounds (MF-PMCs) -- Part 1: Designation system and basis for specifications

GSO ISO 10724-1:2014 塑料 粉末状热塑性材料试样的注射成型 第1部分：多用途试样的一般原理和成型

This part of ISO 10724 specifies the general principles to be followed when injection moulding test specimens of thermosetting powder moulding compounds (PMCs) and gives details of mould designs for preparing one type of specimen for use in establishing reproducible moulding conditions. Its purpose is to promote uniformity in describing the main parameters of the moulding process and also to establish uniform practice in reporting moulding conditions. The particular conditions required for the reproducible preparation of test specimens which will give comparable results will vary for each material used. These conditions are given in the International Standard for the relevant material or are to be agreed upon between interested parties. NOTE ISO round-robin tests with phenolic (PF), urea-formaldehyde (UF), melamine (MF), melamine phenolic (MP) and unsaturated-polyester (UP) injection-moulding materials have shown that mould design is an important factor in the reproducible preparation of test specimens

Plastics -- Injection moulding of test specimens of thermosetting powder moulding compounds (PMCs) -- Part 1: General principles and moulding of multipurpose test specimens

KS I 2207-2014 稀释气和零气中微量成分测定的试验方法

Testing methods for determination of trace components in diluent gas and zero gas

LST EN ISO 4895:2014 塑料. 液态环氧树脂. 结晶倾向性的测定(ISO 4895-2014)

Plastics - Liquid epoxy resins - Determination of tendency to crystallize (ISO 4895:2014)

DIN EN ISO 4895:2014 塑料.液态环氧树脂.结晶趋向的测定(ISO 4895-2014);德文版本EN ISO 4895-2014

Plastics - Liquid epoxy resins - Determination of tendency to crystallize (ISO 4895:2014); German version EN ISO 4895:2014

KS M ISO 4597-1-2014(2019) 环氧树脂用塑料硬化剂和促进剂第1部分:名称

Plastics — Hardners and accelerators for epoxy resins — Part 1: Designation

KS M ISO 4597-1:2014 塑料 环氧树脂硬化剂和促进剂 第1部分：名称

이 표준은 에폭시 수지 경화제와 촉진제의 호칭 방법에 대하여 규정한다.이 호칭 방법의 목적은 각 상용 제품에 “호칭”이라 부르는 숫자 그룹을 할당해 제품에 대한 특정 정보(화학적 설명, 변성제와 용제, 점도, 첨가제)를 코드화된 형태로 제공하는 것이다.따라서 특성이 비슷하고 용도가 동일할 수 있는 모든 제품은 동일한 호칭을 사용하며, 이는 생산자가 데이터 시트에 호칭을 나열하는 경우 사용자의 선택에 도움을 줄 수 있다.?

Plastics — Hardners and accelerators for epoxy resins — Part 1: Designation

JG/T 450-2014 建筑光伏组件用乙烯-醋酸乙烯共聚物(EVA)胶膜

本标准规定了建筑光伏组件用乙烯-醋酸乙烯共聚物(EVA)胶膜(以下简称EVA胶膜)的术语和定义、产品分类、要求、试验方法、检验规则、标志、包装、运输和贮存。本标准适用于安装在建筑围护结构外侧及建筑场地的光伏组件用EVA胶膜。

Ethylene vinyl acetate (EVA) interlayer for building mounted photovoltaic module

KS M ISO 18872:2014 塑料 在高应变率下测定拉伸性能

이 표준은 충격 하중 상황에 근접하는 높은 변형 속도를 포함하는 넓은 범위의 변형 속도에서 성형과 압출 플라스틱의 인장 특성을 측정하는 절차에 대하여 규정한다. 이러한 특성은 낮은 변형 속도 및 중간 변형 속도에서 측정의 조합, 해당 결과의 모델링에 수학 함수 사용, 파라미터의 속도 의존성, 외삽으로 높은 변형 속도에서 파라미터 결정을 통해 측정한다. 그 다음에 높은 변형 속도에서 인장 특성은 계산으로 유도한다. 이 방법을 통해 높은 변형 속도에서 특성을 측정하는 실험적 문제와 관련 오차 발생을 피할 수 있다.낮은 및 중간 변형 속도에서 특성 측정은 이 표준을 적용할 수 있는 플라스틱 재료의 유형을 식별하는 KS M ISO 527-2에 기초한다.?

Plastics — Determination of tensile properties at high strain rates

ASTM D3596-14 凝胶测定标准实践

5.1 The gel (fisheye) in PVC resins is generally recognized as a hard particle of resin which will not fuse when the plastic mass is subjected to set conditions of hot processing. The number of unfused particles present is related to the conditions used. The presence of an excess of such particles is detrimental to many applications. 1.1 This practice provides a quantitative measure of the gels remaining in a flexible vinyl compound processed from general-purpose poly(vinyl chloride) (PVC) resins under a prescribed set of working conditions. 1.2 The values stated in SI units are to be regarded as the standard. The values in parentheses are for information only. 1.3 This standard does not purport to address all of the safety problems, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. Note 1: There is no known ISO equivalent to this standard.

Standard Practice for Determination of Gels (Fisheyes) In General-Purpose Poly(Vinyl Chloride) (PVC) Resins