83.140.10 薄膜和薄板 标准查询与下载

GB/T 17643-1998 土工合成材料 聚乙烯土工膜

本标准规定了聚乙烯土工膜的分类和命名、技术要求、试验方法、检验规则、标志、包装、运输和贮存。 本标准适用于以聚乙烯树脂、乙烯共聚物为原料添加各类助剂所生产的聚乙烯土工膜。

Geosynthetics--Polyethylene geomembrane

GB/T 10005-1998 双向拉伸聚丙烯(BOPP)/低密度聚乙烯(LDPE)复合膜、袋

本标准规定了双向拉伸聚丙烯（BOPP）/低密度聚乙烯（LDPE）经干式或挤出复合的薄膜和包装袋（以下简称膜、袋）的产品分类、要求、试验方法、检验规则、标志、包装、运输、贮存。 本标准适用于以双向拉伸聚丙烯与低密度聚乙烯为基材经干法或挤出复合的膜、袋。产品用于食品、日化产品等轻型包装。

Biaxially oriented polypropylene laminated polyethylene (BOPP/LDPE) films and pouches

GB/T 10004-1998 耐蒸煮复合膜、袋

本标准规定了耐蒸煮复合膜、袋的产品分类，技术要求，试验方法，检验规则及标志、包装、运输和贮存。 本标准适用于以聚酯（PET）、聚丙烯（CPP）、尼龙（PA）薄膜和铝箔（A1）为基材，经干法复合而制成的复合膜、袋（以下简称膜、袋），产品主要用于耐121℃蒸煮的食品包装。

Laminated retort film and pouch

GB/T 10003-1996 普通型双向拉伸聚丙烯薄膜

本标准规定了普通型双向拉伸聚丙烯薄膜（以下简称薄膜）的产品分类、技术要求、试验方法、检验规则、标志、包装、运输、贮存。 本标准适用于以聚丙烯树脂为主要原料，用平膜法或管膜法经双向拉伸而制得的普通用途薄膜，不适用于热封型、消光型、珠光型、电容器用薄膜。

Biaxially oriented polypropylene plain film

GB/T 16578-1996 塑料薄膜和薄片耐撕裂性能试验方法 裤形撕裂法

本标准规定了用裤形撕裂法测定塑料薄膜和薄片的耐撕裂性能。 本标准适用于厚度在1mm以下的软质、硬质材料的薄膜或薄片所切取的标准裤形试样的耐撕裂性能的测定，只要材料在试验中不产生脆性破坏，则试验是有效的。 本标准不适用于测定泡沫材料的耐撕裂性能。

Plastics--Film and sheeting--Determination of tear resistance--Trouser tear method

T/ZZPIA 01-2024 《自然生态降解聚丙烯一次性餐饮具》

本文件规定了自然生态降解聚丙烯一次性餐饮具的术语和定义、技术要求、试验方法、检验规则、标志、标识、包装、运输和贮存。

Natural ecological degradation polypropylene disposable tableware

T/HBFPIA 027-2024 预制食品包装 非复合膜、袋

树脂应符合GB 4806.6的规定;添加剂和用量应符合GB 9685的规定。

Prefabricated food packaging non-composite films and bags

T/SHBX 004-2024 《一次性集装箱液袋》

本文件规定了一次性集装箱液袋（简称液袋）的术语和定义、技术要求、检验方法、检验规则、标志、包装、运输和贮存。

Single-use flexitank

ASTM D7445-24 带泡沫塑料衬垫的硬质聚氯乙烯（PVC）衬垫（背衬乙烯基衬垫）标准规范

Standard Specification for Rigid Poly(Vinyl Chloride) (PVC) Siding with Foam Plastic Backing (Backed Vinyl Siding)

ASTM D4321-24 塑料薄膜包装产量的标准试验方法

Standard Test Method for Package Yield of Plastic Film

GSO ASTM D1709:2024 用自由落镖法测定塑料薄膜抗冲击性的标准试验方法

1.1 These test methods cover the determination of the energy that causes plastic film to fail under specified conditions of impact of a free-falling dart. This energy is expressed in terms of the weight (mass) of the missile falling from a specified height which would result in 50 % failure of specimens tested. 1.2 Two test methods are described: 1.2.1 Test Method A employs a dart with a 38.10 6 0.13-mm (1.500 6 0.005-in.) diameter hemispherical head dropped from a height of 0.66 6 0.01 m (26.0 6 0.4 in.). This test method can be used for films whose impact resistances require masses of about 50 g to about 6 kg to fracture them. 1.2.2 Test Method B employs a dart with a 50.80 6 0.13-mm (2.000 6 0.005-in.) diameter hemispherical head dropped from a height of 1.52 6 0.03 m (60.0 + 0.25, −1.70 in.). Its range of applicability is from about 0.3 kg to about 6 kg. 1.3 Two testing techniques are described: 1.3.1 The standard technique is the staircase method. By this technique, the missile weight employed during the test is decreased or increased by uniform increments after the testing of each specimen, depending upon the result (fail or not fail) observed for the specimen. 1.3.2 The alternative technique provides for testing specimens in successive groups of ten. One missile weight is employed for each group and the missile weight is varied in uniform increments from group to group. 1.3.3 The staircase technique and the alternative technique give equivalent results both as to the values of impact failure weight which are obtained and as to the precisions with which they are determined. 1.4 The values stated in SI units are to be regarded as standard. The values stated in parentheses are for information only. NOTE 1—Tests on materials that do not break, for any reason, are not considered to be valid. It has been noted that certain materials may stretch so far as to bottom out at the base of certain test instruments without actually rupturing. Subcommittee D20.19 is currently considering methods for testing these materials. Anyone interested in participating in a Task Group should contact the Chairman of Subcommittee D20.19 through ASTM International Headquarters. 1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. NOTE 2—Film has been arbitrarily defined as sheeting having nominal thickness not greater than 0.25 mm (0.010 in.). NOTE 3—This test method is technically equivalent to ISO 7765- 1:1988, with the exception of a larger tolerance on the drop height in Test Method B, smaller tolerances on the dart diameters for Test Methods A and B, and the requirement for a vented dart well in 5.1.1. Also, the ISO method does not allow the alternative testing technique described in Section 11 of this test method. 1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Methods for Impact Resistance of Plastic Film by the Free-Falling Dart Method

T/SHPTA 077-2024 锂电池隔膜透气度试验方法

本文件给出了测定锂电池隔膜透气度的试验方法

Test method for air permeance of lithium battery separators

T/SHBX 003-2024 《军用野战食品包装膜、袋》

本文件规定了军用野战食品包装膜、袋的术语、定义和缩略语、分类和技术要求，描述了相关试验方法，给出了检验规则、标志、包装、运输和贮存。

Laminated films and pouches for military battlefield food packaging

T/SHPTA 076-2024 防水透湿热塑性聚氨酯薄膜

本文件规定了防水透湿热塑性聚氨酯（TPU）薄膜的要求、试验方法、检验规则、标志、包装、运输与贮存等

Thermoplastic Polyurethane (TPU) for Waterproof and Breathable Film

T/SHBX 001-2024 《中型散装容器用内衬液袋》

本文件规定了中型散装容器用内衬液袋的术语和定义、分类和结构、技术要求、试验方法、检验规则、标志、包装、运输和贮存。

Liner liquid bags for medium bulk containers

T/CPPIA 41-2024 农业用功能性聚烯烃涂覆棚膜

5　要求 5.1宽度极限偏差 宽度极限偏差应符合表2规定。 5.2厚度极限偏差和厚度平均偏差 厚度极限偏差及厚度平均偏差应符合表3规定。 5.3净质量偏差 每包或卷棚膜的净质量偏差应符合表4规定。 5.4外观 膜面应平整，不应有影响使用的气泡、穿孔、条纹、暴筋、破裂、皱褶等缺陷；涂覆面不应有影响使用的刮蹭.堆叠粘连现象。膜面不应有大于2.0mm的杂质、晶点、僵块；0.6mm～2.0mm的杂质、晶点、僵块，合计每平方米不得多于20个。 5.5力学性能 应符合表5规定。 5.6透光率及雾度 5.6.1　Ⅰ型TF-1、2、3、5棚膜 透光率及雾度应符合表6规定。 5.6.2　Ⅱ型TF-1、2、3、5棚膜 透光率及雾度应符合表7规定。 5.6.3　Ⅲ型棚膜的透光率及雾度 依产品用途和性能要求，由供需双方协定。 5.7流滴性能 5.7.1　涂覆有效性 2小时全幅宽不应出现白色露滴。 5.7.2　初滴性能 棚膜初滴时间应不大于40分钟。 5.7.3　流滴持效期 棚膜流滴失效面积比应符合表8规定。 5.7.4　接触角 5.7.4.1初始接触角 棚膜初始接触角应不大于35°。 5.7.4.2持续性接触角 不同类别棚膜对应水浴时间后接触角应符合表9规定。 5.8耐候性能 TF-1类棚膜，暴露持续时间1200h、TF-2类棚膜，暴露持续时间2200h、TF-3类棚膜，暴露持续时间3000h、TF-5类棚膜，暴露持续时间4600h，纵向断裂标称应变保留率≥60%。

Polyolefin coated functional greenhouse film for agriculture

T/SHPTA 074-2024 纳米纤维防水透气膜

本文件规定了纳米纤维防水透气膜的要求、试验方法、检验规则、标志、包装、运输和贮存等

Nanofiber Waterproof breathable membrane

ASTM D1830-17(2024) 用弯曲电极法测定电绝缘用柔性薄板材料耐热性的标准试验方法

Standard Test Method for Thermal Endurance of Flexible Sheet Materials Used for Electrical Insulation by the Curved Electrode Method

T/SHPTA 073-2024 线缆绕包用聚四氟乙烯薄膜

本文件规定了线缆绕包用聚四氟乙烯薄膜的产品分类、要求、试验方法、检验规则及标志、包装、运输和贮存

Polytetrafluoroethylene film for wires and cables wrapping

ASTM C1349-17(2024) 建筑平板玻璃覆聚碳酸酯标准规范

Standard Specification for Architectural Flat Glass Clad Polycarbonate