83.140.10 薄膜和薄板 标准查询与下载

ASTM F3299-18(2023) 使用电解检测传感器（库仑P2O5传感器）测定水蒸气透过塑料薄膜和薄板的速率的标准试验方法

1.1 This test method covers a procedure for determining the rate of water vapor transmission through flexible barrier materials. The method is applicable to sheets and films consisting of single or multilayer synthetic or natural polymers and foils, including coated materials. It provides for the determination of water vapor transmission rate (WVTR). 1.2 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Method for Water Vapor Transmission Rate Through Plastic Film and Sheeting Using an Electrolytic Detection Sensor (Coulometric P2O5 Sensor)

ASTM D1434-23 测定塑料薄膜和片材透气特性的标准试验方法

1.1 This test method utilizes a manometric method to determine the steady-state rate of transmission of a gas through plastics in the form of film, sheeting, laminates, and plasticcoated papers or fabrics. This test method provides for the determination of (1) gas transmission rate (GTR), (2) permeance, and, in the case of homogeneous materials, (3) permeability. 1.2 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Method for Determining Gas Permeability Characteristics of Plastic Film and Sheeting

T/SDMS 008-2023 聚四氟乙烯（PTFE）声学复合膜

以PTFE树脂为原料，采用国际先进的增材制造新工艺开发PTFE声学复合膜，产品强度均匀、厚度均匀（公差控制在0.01微米内）、孔径均匀（公差控制在0.01微米内）。

PTFE acoustic compounded membrane

T/SHBX 004-2023 《双向拉伸聚酰胺（BOPA）/聚乙烯（PE）复合膜、袋》

本文件规定了双向拉伸聚酰胺（BOPA）/聚乙烯（PE）复合膜、袋（以下简称膜、袋）的术语和定义、分类、要求、试验方法、检测规则及标志、包装、运输和贮存。

Biaxially oriented polyamide/polyethylene laminated films and pouches for packaging

T/CHBAS 28-2023 遇水膨胀型密封带（新型生料带）

本文件规定了遇水膨胀型密封带（新型生料带）的技术要求、试验方法、检验规则、标志、包 装、运输和贮存。 本文件适用于以特制无纺布为基材，表面复合高分子吸水膨胀剂和保湿增粘剂制成的用于管道 螺纹连接密封的膨胀型密封带的生产及交验货用。

Water-swellable sealing tape (new raw material tape)

T/BYXT 017-2023 稀土抗菌保护膜

性能要求 产品性能应符合表1的要求。 表1 性能要求 项目　要求 　软性贴膜　钢化玻璃膜 硬度　用2H硬铅笔划过表面应无划痕　应能承受硬度为 9H级别的铅笔在500g负载下以45°角压推过无划伤、划痕。 耐摩擦　500次耐磨测试后，产品不应出现穿透现象　3000次耐磨测试后，产品不应出现穿透现象 抗冲击性　/　产品经冲击试验后，无破损，不影响正常使用 蓝光投射性能　/　当产品明确具有蓝光防护功能时，其蓝光透射比π sb应不大于（86+0.5）%。 表1 （续） 可见光透射比　透光膜可见光投射率不应低于90%，半透光膜可见光投射率不应低于35%。 耐黄变　使用UV-A340灯管，0.65mv，60℃的温度持续测试8h后，产品不可有明显发黄或变色。 温度要求　试验高温 40℃±3℃，低温-20℃±2℃，分别持续时间 24h。每次试验后恢复到常温进行测试，高温与低温试验情况下，产品外观都不应出现变形现象。 胶质残留　将产品粘贴在洁净的玻璃板上，静置12h 后剥离，玻璃板上应无胶质残留。 防指纹、抗油污　用油性笔在产品表面画线，笔迹是易被擦拭掉的，擦拭后产品无油污痕迹。 持粘性c　≥4h 静电吸附性能d　100次剥离贴合无影响。 a 仅适用于背胶粘贴膜类产品。 b 仅适用于静电吸附膜类产品。 6.4 抗抑菌要求 产品抗抑菌应符合表2的要求。 表2 抗抑菌要求 项目　抑菌率　抗菌率　新冠病毒抑制率　防霉等级 指标　90.00%-99.99%　90.00%-99.99%　90.00%-99.99%　0级-1级 注：稀土抗抑菌涂料应根据产品对抗抑菌功能的需求，选择相应的抗抑菌功能项目，应符合5.2的要求。 6.5 有害限量物要求 产品有害限量物应符合表3的要求。 表3 有害限量物要求 项目　单位　限值 镉及铬化合物　mg/kg　＜ 5 铅及铅化合物　mg/kg　＜ 5 汞及汞化合物　mg/kg　＜ 5 六价铬化合物　mg/kg　＜ 5 多溴联苯　mg/kg　不得检出 多溴二苯醚　mg/kg　不得检出

Rare earth antibacterial resist film

T/BYXT 016-2023 稀土抗菌薄膜

6.1 抗抑菌要求 6.1.1 产品牌号、抗抑菌基础材料载锌抗抑菌粉含量及制备工艺方法，应符合表2 的要求。 表2 产品牌号、抗抑菌材料含量及制备工艺方法 产品牌号　产品名称　载锌抗抑菌粉a含量（质量分数/%)　制备工艺方法 REA-FILM01-2Nb　稀土抗菌包装用塑料复合膜、袋　0.1-5　掺混法 REA-FILM02-2N　稀土抗菌包装用聚乙烯热收缩薄膜　　 REA-FILM03-2N　稀土抗菌双向拉伸聚苯乙烯窗口薄膜　　 REA-FILM04-2N　稀土抗菌双向拉伸聚苯乙烯扭结薄膜　　 REA-FILM05-2N　稀土抗菌双向拉伸聚丙烯可涂覆合成纸薄膜　　涂覆法 REA-FILM06-2N　稀土抗菌流延聚丙烯(CPP)薄膜　　掺混法 REA-FILM07-2N　稀土抗菌食品包装用多层共挤膜、袋　　涂覆法 REA-FILM08-2N　稀土抗菌食品包装用塑料与铝箔复合膜、袋　　 REA-FILM09-2N　稀土抗菌食品包装用纸与塑料复合膜、袋　　 REA-FILM10-2N　稀土抗菌双向拉伸聚丙烯消光薄膜　　掺混法 REA-FILM11-2N　稀土抗菌双向拉伸聚苯乙烯热收缩薄膜　　 REA-FILM12-2N　稀土抗菌食品包装用塑料与铝箔蒸煮复合膜、袋　　涂覆法 REA-FILM13-2N　稀土抗菌食品包装用纸铝塑复合膜、袋　　 REA-FILM14-2N　稀土抗菌食品包装用复合塑料盖膜　　 REA-FILM15-2N　稀土抗菌聚全氟乙丙烯（FEP）薄膜　　掺混法 REA-FILM16-2N　稀土抗菌聚四氟乙烯双向拉伸过滤薄膜　　 a   稀土抗抑菌基础材料载锌抗抑菌粉，应符合T/BYXT 003.1-2022第4章的要求。 b  产品牌号参考GB/T 17803的表示方法，第一层用稀土抗抑菌（Rare earth antibacterial）首字母“REA”表示；第二层“FILM01”表示分类号为01的稀土抗菌薄膜产品（“FILM”为薄膜的英文名称）；第三层“2N”表示抗抑菌率为99%（2为“9”的个数，“N”为数字“9”的英文首字母）。 6.1.2 产品抗抑菌性能应符合表3的要求。 表3 产品抗抑菌性能指标 项目　抑菌率　抗菌率　新冠病毒抑制率　防霉等级 指标　90.00%-99.99%　90.00%-99.99%　90.00%-99.99%　0级～1级 注：稀土抗抑菌涂料应根据产品对抗抑菌功能的需求，选择相应的抗抑菌功能项目，应符合5.2的要求。

Rare earth antibacterial film

T/WS 0006-2023 锂电池用阻燃聚丙烯麦拉膜

力学性能 项 目　要  求 拉伸强度，MPa　纵向　≥29          横向　≥27 断裂伸长率，%　        纵向　≥480        横向　≥430 穿刺强度，N/mm　≥80 浸润张力a(电晕后，背胶面)，mN/m　≥38 a   浸润张力仅适用于电晕麦拉膜。 电气性能 项 目　要 求 介电强度，kV/mm　≥65 体积电阻率，Ω·cm　≥1×1016 表面电阻率，Ω　≥5×1014

Flame retardant polypropylene Mai La film for lithium-ion battery

T/CIPR 067-2023 大通量加强型聚偏氟乙烯（PVDF）不带衬超滤膜

本文件规定了大通量加强型聚偏氟乙烯（PVDF）不带衬超滤膜的术语和定义、技术要求、试验方法、检验规则、标志、包装、运输和贮存。 本文件适用于各种大通量加强型聚偏氟乙烯（PVDF）不带衬超滤膜的制造技术，其他不同类型的滤膜可参照使用。

Large-flux reinforced polyvinylidene fluoride (PVDF) unlined ultrafiltration membrane

T/CIPR 057-2023 纸尿裤抗菌塑料包装袋

本文件规定了纸尿裤抗菌塑料包装袋的术语和定义、分类、技术要求、试验方法、检验规则、标志、包装、运输和贮存。 本文件适用于纸尿裤包装用的抗菌塑料包装袋。

Diaper antibacterial plastic packaging bag

T/SHPTA 038-2023 光伏背板用聚酯薄膜

本标准适用于光伏背板用聚酯薄膜

Polyester film for photoelectric display

T/SHBX 001-2023 《工业包装用无溶剂铝塑复合膜、袋》

本文件规定了工业包装用无溶剂铝塑复合膜、袋的分类、要求、试验方法、检验规则、标志、包装、运输和贮存。

Solventless aluminum foil-plastic laminated film and pouch for commerce packaging

ASTM D2578-23 聚乙烯和聚丙烯薄膜润湿张力的标准试验方法

1.1 This test method covers the measurement of the wetting tension of a polyethylene or polypropylene film surface in contact with drops of specific test solutions in the presence of air. 1.2 The values stated in SI units are to be regarded as standard. The values given in parentheses are mathematical conversions to inch-pound units that are provided for information only and are not considered standard. NOTE 1—This test method and the specified reagents were specifically developed for polyethylene and polypropylene films. It is possible to utilize this test method and the specified reagents for films composed of other polymers, but this can affect the surface energies of the gas-liquid and solid-liquid interfaces, which will affect the contact angle and wetting tension. The applicability and significance for use of non-polyolefin materials must be established by the user. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. Specific hazards statements are given in Section 9. NOTE 2—This test method is equivalent to ISO 8296. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Method for Wetting Tension of Polyethylene and Polypropylene Films

ASTM E720-23 电子辐射硬度试验中中子光谱测定用中子传感器的选择和使用标准指南

1.1 This guide covers the selection and use of neutronactivation detector materials to be employed in neutron spectra adjustment techniques used for radiation-hardness testing of electronic semiconductor devices. Sensors are described that have been used at many radiation hardness-testing facilities, and comments are offered in table footnotes concerning the appropriateness of each reaction as judged by its cross-section accuracy, ease of use as a sensor, and by past successful application. This guide also discusses the fluence-uniformity, neutron self-shielding, and fluence-depression corrections that need to be considered in choosing the sensor thickness, the sensor covers, and the sensor locations. These considerations are relevant for the determination of neutron spectra from assemblies such as TRIGAand Godiva-type reactors and from Californium irradiators. This guide may also be applicable to other broad energy distribution sources up to 20 MeV. NOTE 1—For definitions on terminology used in this guide, see Terminology E170. 1.2 This guide also covers the measurement of the gammaray or beta-ray emission rates from the activation foils and other sensors as well as the calculation of the absolute specific activities of these foils. The principal measurement technique is high-resolution gamma-ray spectrometry. The activities are used in the determination of the energy-fluence spectrum of the neutron source. See Guide E721. 1.3 Details of measurement and analysis are covered as follows: 1.3.1 Corrections involved in measuring the sensor activities include those for finite sensor size and thickness in the calibration of the gamma-ray detector, for pulse-height analyzer deadtime and pulse-pileup losses, and for background radioactivity. 1.3.2 The primary method for detector calibration that uses secondary standard gamma-ray emitting sources is considered in this guide and in Test Methods E181. In addition, an alternative method in which the sensors are activated in the known spectrum of a benchmark neutron field is discussed in Guide E1018. 1.3.3 A data analysis method is presented which accounts for the following: detector efficiency; background subtraction; irradiation, waiting, and counting times; fission yields and gamma-ray branching ratios; and self-absorption of gamma rays and neutrons in the sensors. 1.4 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Guide for Selection and Use of Neutron Sensors for Determining Neutron Spectra Employed in Radiation-Hardness Testing of Electronics

ASTM F736-17(2023) 用落锤法测定整体聚碳酸酯板抗冲击性的标准试验方法

1.1 This test method covers the determination of the energy required to initiate failure in monolithic polycarbonate sheet material under specified conditions of impact using a free falling weight. 1.2 Two specimen types are defined as follows: 1.2.1 Type A consists of a flat plate test specimen and employs a clamped ring support. 1.2.2 Type B consists of a simply supported three-point loaded beam specimen (Fig. 1) for use with material which can not be failed using the Type A specimen. For a maximum drop height of 6.096 m (20 ft) and a maximum drop weight of 22.68 kg (50 lb), virgin polycarbonate greater than 12.70 mm (1⁄2 in.) thick will require use of the Type B specimen. NOTE 1—See also ASTM Methods: D1709, D2444 and D3029. 1.3 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.3.1 Exception—The inch-pound units in parentheses are provided for information only. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. For specific hazard statement, See Section 7. 1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Method for Impact Resistance of Monolithic Polycarbonate Sheet by Means of a Falling Weight

T/SHBX 014-2022 包装用铝塑复合膜、袋

Aluminum-plastic composite film and bag for packaging

T/ZZB 2877-2022 热封型双向拉伸聚丙烯（BOPP）薄膜

本文件规定了热封型双向拉伸聚丙烯（BOPP）薄膜（以下简称“薄膜”）的术语和定义、基本要求、技术要求、试验方法、检验规则、标志、包装、运输及贮存和质量承诺。 本文件适用于以聚丙烯为主要原料，用平膜法经双向拉伸成型制得的单面热封型聚丙烯薄膜。 本文件不适用于其他特殊功能的双向拉伸聚丙烯薄膜，如双向拉伸聚丙烯消光薄膜、双向拉伸聚丙烯珠光薄膜、双向拉伸聚丙烯拉线用薄膜、双向拉伸聚丙烯电容器用薄膜、双向拉伸聚丙烯香烟包装薄膜等。

Biaxially oriented polypropylene（BOPP） film for heat sealing

T/SHBX 013-2022 《耐穿刺、高阻隔塑料复合薄膜及包装袋》

本文件规定了耐穿刺、高阻隔塑料复合薄膜及包装袋的术语和定义、缩略语、分类、要求、试验方法、检验规则、标志、包装、运输和贮存。

Puncture resistant and high barrier plastic composite film and packaging bag

T/SHPTA 030-2022 民用航空器用聚氟乙烯基阻燃耐候复合装饰膜

本文件适用于民用航空器内，尤其是大中小型客机的舱内装饰应用。 

Polyvinyl-fluoride?flame-retardant & weathering-resistant decorative laminates for civil aviation

T/IGIA 012-2022 高阻隔吨袋 内袋用塑料与铝箔复合膜 售后服务规范

本标准规定了高阻隔吨袋内袋用塑料与铝箔复合膜售后服务的基本原则、服务制度、服务人员、服务提供、服务范畴、服务评价等。

Specification for after-sales service of inner bag with Plastics and aluminum foil laminated films for high barrier ton bag