83.140.50 密封件 标准查询与下载

HG/T 3980-2007 汽车轴承用密封圈

本标准规定了汽车轴承用骨架式橡胶密封圈的要求、试验方法、检验规则及标志、包装、贮存和运输。 本标准适用于汽车轴承用骨架式橡胶密封圈。

Sealing rings of automobile bearing

ASTM C509-06(2015) 弹性泡沫预制垫片和密封材料的标准规格

9.1 Flame Propagation:  9.1.1 This specification has two options: 9.1.1.1 Option I—Flame propagation test is required. 9.1.1.2 Option II—Flame propagation test is not required. 9.1.2 In case no option is specified, Option I will apply. 9.2 This specification has two classifications as related to ozone resistance. These are Type I and Type II, with the latter having the greater resistance to ozone. The type should be specified when making reference to this specification but in the event that the type is not specified, Type II shall apply. Note 2: Type II is included in this specification for use where greater ozone resistance is required. 1.1 This specification applies to those elastomeric cellular materials of a firm grade that are manufactured in preformed shapes for use as gaskets and for use as sealing materials, in the form of compression seals or gaskets, or both, for glazing other building joint applications. Note 1: For softer cellular elastomeric materials used in secondary sealing applications, refer to Specification D1056. 1.2 Test Method C1166, as referenced in this specification, should be used to measure and describe the properties of materials, products, or assemblies in response to heat and flame under controlled laboratory conditions and should not be used to describe or appraise the fire hazard or fire risk of materials, products, or assemblies under actual fire conditions. However, results of this test may be used as elements of a fire risk assessment which takes into account all of the factors which are pertinent to an assessment of the fire hazard of a particular end use. 1.3 The following precautionary caveat pertains only to the test method portion, Section 11, of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. 1.4 The committee with jurisdiction over this standard is not aware of any comparable standards published by other organizations.

Standard Specification for Elastomeric Cellular Preformed Gasket and Sealing Material

LST EN 682-2003/A1-2005 弹性密封件 用于输送气体和碳氢化合物流体的管道和配件的密封件的材料要求

Elastomeric seals - Materials requirements for seals used in pipes and fittings carrying gas and hydrocarbon fluids

DS/EN 682/A1:2005 弹性密封件 用于输送气体和碳氢化合物流体的管道和配件的密封件的材料要求

This Standard specifies requirements for elastomeric materials used in seals for supply pipes and fittings, ancillaries and valves at operating temperatures in general from -5 degrees C up to 50 degrees C and in special cases from -15 degrees C up to 50 degrees C.

Elastomeric seals - Materials requirements for seals used in pipes and fittings carrying gas and hydrocarbon fluids

HG/T 2813-2005 软木橡胶密封制品 第二部分 机动车辆用

本部分规定了机动车辆用软木橡胶密封制品的要求、试验方法、检验规则、标志、包装、运输和贮存。 本标准适用于汽车、拖拉机、铁路机车、摩托车等机动车辆在紧固力为2MPa～3MPa、使用温度在-40℃～+120℃下的静密封软木橡胶制品。

Cork-rubber sealing articles Part 2 Used for motor vehicle

HG/T 2812-2005 软木橡胶密封制品 第一部分 变压器及高压电器类用

本标准规定了油浸式变压器及高压电器类用软木橡胶密封制品的要求、试验方法、检验规则、标志、包装、运输和贮存。 本标准适用于油浸式变压器和高压电器类及其配套组件用的软木橡胶密封制品。

Cork-rubber sealing articles Part 1 Used for transformer and electrical equipment of high voltage

ASTM D5898-96(2005) 贴片防水标准细节标准指南

Standard Guide for Standard Details for Adhered Sheet Waterproofing

ISO 16010:2005 弹性密封件.传送气体燃料和烃类液体的管和配件用密封件的材料要求

This International Standard specifies requirements for elastomeric materials used in seals for supply pipes and fittings, ancillaries and valves at operating temperatures in general from -5 ℃ up to 50 ℃ and in special cases from -15 ℃ up to 50 ℃, for the following: a) general applications (see Table 4, type G series): — gaseous fuel [manufactured, natural and liquefied petroleum gas (LPG) in the gaseous phase], — hydrocarbon fluids with an aromatic content up to 30 % (by volume), including LPG in the liquid phase; b) special applications (see Table 4, type H): — materials suitable for carrying gaseous fuels containing gas condensates and hydrocarbon fluids of unrestricted aromatic content. General requirements for finished joint seals are also given; any additional requirements called for by the particular application are specified in the relevant product standards, taking into account that the performance of pipe joints is a function of the seal material properties, seal geometry and pipe joint design. This International Standard should be used where appropriate with product standards which specify performance requirements for joints. This International Standard is applicable to joint seals for all pipeline materials, including iron, steel, copper and plastics. In the case of composite sealing rings, the requirements in 4.2.8 and 4.2.9 apply only when the materials used for any elastomeric parts come into contact with gaseous fuel or hydrocarbon fluid. Elongation at break, tensile strength, compression set and stress relaxation requirements for materials of hardness classes 80 and 90 apply only when they constitute that part of the seal which participates directly in the sealing function or contributes directly to long-term stability. This International Standard is not applicable to the following: — seals made from cellular materials; — seals with enclosed voids as part of their design; — seals required to be resistant to flame or to thermal stress; — seals which contain splices joining pre-vulcanized profile ends.

Elastomeric seals - Material requirements for seals used in pipes and fittings carrying gaseous fuels and hydrocarbon fluids

HG/T 3098-2004 混凝土道路伸缩缝用预成型硫化橡胶压缩密封件材料规范

本标准规定了混凝土道路伸缩缝用预成型硫化橡胶压缩密封件材料的性能要求和试验方法。 本标准适用于混凝土结构的道路伸缩缝用密封材料，不适用于沥青等其他结构的道路伸缩缝用密封材料。 本标准不规定密封件的型式与尺寸，但密封件的尺寸公差应符合GB／T 3672．1的规定。

Rubber, vulcanized-preformed compression seals for use between concrete motorway paving sections-specification for material

BS ISO 9631:2004 橡胶密封件.温度为110℃及以下的热水供给、排水和污水管道用连接环.材料规范

This International Standard specifies requirements for materials used in vulcanized-rubber seals for hot potable and non-potable water supply (up to 110 ℃). The different seal designations specified are defined according to seal type, seal application and the requirements for a particular seal (see Table 3). General requirements for finished joint seals are also given. Any additional requirements called for by the particular application are specified in the relevant product standards, taking into account that the performance of pipe joints is a function of the seal material properties, seal geometry and pipe joint design. This International Standard is intended to be used where appropriate with product standards which specify performance requirements for joints. This International Standard is applicable to joint seals for use with all pipeline materials, including iron, steel, clay, fibre cement, concrete, reinforced concrete, plastics and glass-reinforced plastics. It is applicable to elastomeric components of composite and non-composite seals. In the case of composite seals made from materials with hardnesses ranging from 76 IRHD to 95 IRHD, the requirements for elongation at break, compression set and stress relaxation apply only when the material participates in the sealing function or contributes to the long-term stability of the seal. Joint rings made from cellular rubber materials or with enclosed voids as part of their design are not covered by this International Standard.

Rubber seals - Joint rings for pipelines for hot water supply, drainage and sewerage pipelines up to 110 °C - Specifications for the material

ISO 9631:2003 橡胶密封件.温度为110℃及以下的热水供给管道用密封圈.材料规范

This International Standard specifies requirements for materials used in vulcanized-rubber seals for hot potable and non-potable water supply (up to 110 ℃). The different seal designations specified are defined according to seal type, seal application and the requirements for a particular seal (see Table 3). General requirements for finished joint seals are also given. Any additional requirements called for by the particular application are specified in the relevant product standards, taking into account that the performance of pipe joints is a function of the seal material properties, seal geometry and pipe joint design. This International Standard is intended to be used where appropriate with product standards which specify performance requirements for joints. This International Standard is applicable to joint seals for use with all pipeline materials, including iron, steel, clay, fibre cement, concrete, reinforced concrete, plastics and glass-reinforced plastics. It is applicable to elastomeric components of composite and non-composite seals. In the case of composite seals made from materials with hardnesses ranging from 76 IRHD to 95 IRHD, the requirements for elongation at break, compression set and stress relaxation apply only when the material participates in the sealing function or contributes to the long-term stability of the seal. Joint rings made from cellular rubber materials or with enclosed voids as part of their design are not covered by this International Standard.

Rubber seals - Joint rings for pipelines for hot-water supply up to 110 degrees C - Specification for the material

LST EN 682-2003 弹性密封件 用于输送气体和碳氢化合物流体的管道和配件的密封件的材料要求

Elastomeric Seals - Materials requirements for seals used in pipes and fittings carrying gas and hydrocarbon fluids

DS/EN 682:2003 弹性密封件 用于输送气体和碳氢化合物流体的管道和配件的密封件的材料要求

This standard specifies requirements for elastomeric materials used in seals for supply pipes and fittings, ancillaries and valves at operating temperatures in general from -5 degrees C up to 50 degrees C and in special cases from -15 degrees C up to 50 degrees C.

Elastomeric Seals - Materials requirements for seals used in pipes and fittings carrying gas and hydrocarbon fluids

DS/EN 13787:2002 用于进气压力高达 100 巴的气压调节器和相关安全装置的弹性体

This standard specifies the minimum requirements for elastomeric materials intended to be used as static seals, dynamic seals or diaphragms in the gas pressure requlators covered by EN 334 and in the safety devices for gas pressure regulating stations and installations covered by the corresponding European Standards, as well as the relevant test methods to assess these requirements.

Elastomers for gas pressure regulators and associated safety devices for inlet pressures up to 100 bar

ISO 4633:2002 橡胶密封.供水、排水和污水管道用密封圈.材料规范

This International Standard specifies requirements for materials used in vulcanized rubber seals for a) cold drinking-water supplies (up to 50 ℃); b) drainage, sewerage and rainwater systems (continuous flow up to 45 ℃ and intermittent flow up to 95 ℃). The different designations of seals specified are defined according to their type, application and requirements (see Table 3). General requirements for finished joint seals are also given: any additional requirements called for by the particular application are specified in the relevant product standards, taking into account that the performance of pipe joints is a function of the seal material properties, seal geometry and pipe joint design. This tnternational Standard is intended to be used where appropriate with product standards which specify performance requirements for joints. This International Standard is applicable to joint seals for all pipeline materials, including iron, steel, clay, fibre cement, concrete, reinforced concrete, plastics and glass-reinforced plastics. It is applicable to elastomeric components of composite or non-composite seals. In the case of composite seals for materials of hardness ranges from 76 IRHD to 95 IRHD, the requirements for elongation at break, compression set and stress relaxation apply only when the material is participating in the sealing function or in the long-term stability of the seal. Joint seals made with an enclosed void as part of their design are included in the scope of this International Standard.

Rubber seals - Joint rings for water supply, drainage and sewerage pipelines - Specification for materials

HG/T 3089-2001 燃油用O形橡胶密封圈材料

本标准规定了石油基燃油系统用O形橡胶密封圈材料的要求、抽样、试验方法及标志、标签、包装、贮存。 本标准适用于在石油基燃油系统、-40～100℃下使用的O形橡胶密封圈材料。

Rubber mixture of O-ring seals for fuel

HG/T 3096-2001 水闸橡胶密封件

本标准规定了水闸橡胶密封件的分类、要求、抽样、试验方法及标志、包装、贮存和运输。 本标准适用于水利、水电工程闸门用的橡胶密封件。

Rubber gate seals

HG/T 3087-2001 静密封橡胶零件贮存期快速测定方法

本标准适用于测定静密封橡胶零件在未变形和变形(径向压缩12%～25%，轴向压缩15%～40%)状态下，在空气和各种油介质中，在仓库贮存条件下保持工作能力的贮存期限。 本方法不适用于易水解的橡胶，例如硅橡胶、聚氨酯、丙烯酸酯和氯醇橡胶等制造的零件在其贮存时与空气接触的情况。 按照本方法测定的橡胶零件贮存期，可作为制定产品贮存期的依据之-。

Method of accelerated determination for Shelf-life of rubber static sealing parts

HG/T 3091-2000 橡胶密封件.给、排水管及污水管道用接口密封圈.材料规范

Rubber seals.Joint rings for water supply,drainage and sewerage pipelines.Specification for materials

HG 2950-1999 汽车制动气室橡胶隔膜

本标准规定了汽车制动气室橡胶隔膜的要求、抽样、试验方法及标志、包装、运输和贮存。 本标准适用于汽车制动气室用橡胶隔膜。

Rubber diaphragms for brake chamber in automobiles