83.160.20 标准查询与下载

SAE ARP4834-1995 飞行器轮胎翻新操作规程.斜交和辐条

This SAE Aerospace Recommended Practice (ARP) sets forth criteria for the selection, inspection, retread and repair of worn civil aircraft tires, and the means to verify that the retreaded tire is suitable for continued service. This document is applicable to both bias ply and radial aircraft tires qualified subsequent to the adoption of this document. This document sets for the minimum recommended requirements for retreaded tires used on civil aircraft. It also provides criteria for the escalation of retread level of tires used on civil aircraft. The combined recommendations contained in this document form, an acceptable practice, but not the only practice, for retreaded aircraft tires.

Aircraft Tire Retreading Practice - Bias and Radial

SAE AS4833-1995 航空器新型轮胎标准.偏差和半径

This SAE Aerospace Standard (AS) sets forth criteria for the selection and verification processes to be followed in providing tires that will be suitable for intended use on civil aircraft. This document encompasses new and requalified radial and bias aircraft tires. This document establishes the minimum recommended performance standards for new tires to be used on civil aircraft. All new or requalified tires shall meet these standards.

Aircraft New Tire Standard - Bias and Radial

BS C 22:1995 飞机内胎和无内胎轮胎气门嘴的测试方法 芯和帽

This International Standard specifies the test methods used for valve cores and caps for aircraft tyres, with or without inner tubes, and minimum airtightness standards. It constitutes a detailed method allowing products to be evaluated on the same basis, and re-sults to be compared.

Test methods for aircraft inner tube and tubeless tyre valves. Cores and caps

ISO 9475:1994 有内胎和无内胎的航空器轮胎 气门咀、孔及帽 试验方法

Specifies the test methods used for valve cores and caps for aircraft tyres, with or without inner tubes, and minimum airtightness standards. Constitutes a detailed method allowing products to be evaluated on the same basis, and results to be compared.

Aircraft inner tube and tubeless tyre valves - Cores and caps - Test methods

ISO 3324-1:1993 飞机轮胎和轮辋.第1部分:规范

Aircraft tyres and rims — Part 1: Specifications

GOST R ISO 3324-2-1993 航空器轮胎及轮辋 第2部分：轮胎测试方法

Aircraft tyres. Test methods for tyres

NAVY MS14147 REV A VALID NOTICE 1-1991 重整NAVY飞机轮胎业务适应性(飞行)试验

MS14147A(AS), dated 10 June 1983, has been reviewed and determined to be valid for use in acquisition.

SERVICE SUITABILITY (FLIGHT) TESTING OF REBUILT NAVY AIRCRAFT TIRES

NAVY MS14113 REV E-1990 飞机轮胎彩色编码识别带

ALL AIRCRAFT TIRES MANUFACTUREO/REDUILT FOR THE DEPARTMENT OF DEFENSE SHALL BE TAPED BEFORE DELIVERY, WITH A CIRCUMFERENTIAL BAND OF ONE (1) INCH, PRESSURE-SENSITIVE TAPE, COMPLETELY AROUND THE CENTERMOST RIB OF THE TREAD.

TAPE, IDENTIFICATION, COLOR CODED, FOR AIRCRAFT TIRES

SAE AS707B-1988 真空胎飞机轮的热敏感膨胀压力释放装置

This standard establishes minimum design, installation, qualification, and operational requirements for thermally actuated, pressure release devices for use only in tubeless tire type aircraft wheels. These devices are designed to completely release the contained inflation pressure from a tubeless tire and wheel assembly when brake generated heat causes the assembly to exceed a safe temperature operating level. The objective is to prevent tire or wheel rupture from brake generated heat which could cause serious personnel injuries or serious aircraft operational hazards.

Thermal Sensitive Inflation Pressure Release Devices for Tubeless Aircraft Wheels

NAVY MS14193 VALID NOTICE 1-1987 飞机轮胎寿命周期成本(LCC)规程

MS 14193(AS), 9 October 1979, has been reviewed and determined to be current .

AIRCRAFT TIRE LIFE CYCLE COSTING (LCC), PROCEDURES FOR

NF L82-690:1984 飞机气动阀门

Aircraft tyre valves.

NAVY MS14147 REV A-1983 重整NAVY飞机轮胎业务适应性(飞行)试验

SERVICE SUITABILITY (FLIGHT) TESTING OF REBUILT NAVY AIRCRAFT TIRES

SERVICE SUITABILITY (FLIGHT) TESTING OF REBUILT NAVY AIRCRAFT TIRES

ISO 7295:1982 轮胎气门嘴.飞机.互换性尺寸

Tyre valves — Aircraft — Interchangeability dimensions

SAE AS666C-1982 航空器无管轮胎车轮用静态密封的空腔设计和O型环选择

This specification has been declared "NONCURRENT" as of January 2005. It is recommended, therefore, that this document not be specified for new designs. Each of these "NONCURRENT" documents is available from SAE. Document made inactive for new designs. Committee feels that the practice amongst wheel manufacturers is to use proprietary gland standards and materials to improve seal integrity rendering this document obsolete for new design. This document shall be retained for historical record only.

Cavity Design and O-Ring Selection for Static Seal Use in Aircraft Tubeless Tire Wheels

SAE AS666B-1982 用于飞机无内胎轮毂静密封的腔设计和O型圈选择R(1993)

This specification has been declared "NONCURRENT" as of January 2005. It is recommended, therefore, that this document not be specified for new designs. Each of these "NONCURRENT" documents is available from SAE. Document made inactive for new designs. Committee feels that the practice amongst wheel manufacturers is to use proprietary gland standards and materials to improve seal integrity rendering this document obsolete for new design. This document shall be retained for historical record only.

Cavity Design and O-Ring Selection for Static Seal Use in Aircraft Tubeless Tire Wheels R(1993)

NAVY MS14193-1979 飞机轮胎寿命周期成本(LCC)规程

AIRCRAFT TIRE LIFE CYCLE COSTING (LCC), PROCEDURES FOR

AIRCRAFT TIRE LIFE CYCLE COSTING (LCC), PROCEDURES FOR

NF L82-680:1970 飞机起落架.飞机轮胎尺寸和间隙的测定

DETERMINING DIMENSIONS AND SAFETY CLEARANCES FOR AIRCRAFT TYRES.

NF L82-691:1954 飞机起落架.低压内胎阀门

AIRCRAFT LANDING GEAR. LOW-PRESSURE INNER TUBE VALVES.

NF L82-672:1954 飞机起落架.副起落架低压轮胎

AIRCRAFT LANDING GEAR. LOW-PRESSURE TYRES FOR AUXILIARY UNDERCARRIAGE. (RECH.).

NF L82-671:1954 飞机起落架.主起落架低压轮胎

AIRCRAFT LANDING GEAR. LOW-PRESSURE TYRES FOR MAIN UNDERCARRIAGE. (RECH.).