87.020 涂料涂覆工艺 标准查询与下载

GSO ISO 12944-7:2013 油漆和清漆 保护钢结构免受腐蚀的预防性涂层系统 第7部分：涂装工程的实施和监督

1.1 This part of ISO 12944 deals with the execution and supervision of paint work on steel structures in the workshop or on site. 1.2 This part of ISO 12944 does not apply to: — the preparation of surfaces to be painted (see ISO 12944-4) and the supervision of such work, — the application of metallic coatings, — pre-treatment methods such as phosphating and chromating and paint application methods such as dipping, powder coating or coil coating.

Paints and varnishes -- Corrosion protection of steel structures by protective paint systems -- Part 7: Execution and supervision of paint work

KS M ISO 16276-2-2013(2018) 防护涂料体系对钢结构的腐蚀防护.涂层附着力/内聚力（断裂强度）的评定和验收标准.第2部分:横切试验和X-切试验

Corrosion protection of steel structures by protective paint systems ㅡ Assessment of, and acceptance criteria for, the adhesion/cohesion (fracture strength) of a coating ㅡ Part 2: Cross-cut testing an

KS M ISO 16276-1-2013(2018) 防护涂料体系对钢结构的腐蚀防护第1部分:拉脱试验涂层附着力/内聚力（断裂强度）的评定和验收标准

Corrosion protection of steel structures by protective paint systems ㅡ Assessment of, and acceptance criteria for, the adhesion/cohesion (fracture strength) of a coating ㅡ Part 1: Pull-off testing

GSO ISO 12944-6:2013 油漆和清漆 防护漆系统对钢结构的腐蚀防护 第6部分：实验室性能测试方法

This part of ISO 12944 specifies laboratory test methods and test conditions for the assessment of paint systems for the corrosion protection of steel structures. The test results are to be considered as an aid in the selection of suitable paint systems and not as exact information for determining durability. This part of ISO 12944 covers protective paint systems designed for application to uncoated steel, hot-dip-galvanized steel and steel surfaces with thermally sprayed zinc coatings. This part of ISO 12944 does not apply to protective paint systems for electroplated or painted steel. Certain tests in this part of ISO 12944 are not applicable to many water-borne paint systems (see 4.2). Nevertheless, some water-borne paint systems are amenable to testing and evaluation using the procedures described herein, and their results could be taken into account. The environments defined in ISO 12944-2 are considered

Paints and varnishes -- Corrosion protection of steel structures by protective paint systems -- Part 6: Laboratory performance test methods

GSO ISO 12944-1:2013 油漆和清漆 防护涂料系统对钢结构的腐蚀防护 第1部分：概述

1.1 ISO 12944 deals with the corrosion protection of steel structures by protective paint systems. 1.2 ISO 12944 covers only the corrosion-protective function of paint systems. Other protective functions, like the protection against: — microorganisms (marine fouling, bacteria, fungi, etc.), — chemicals (acids, alkalis, organic solvents, gases, etc.), — mechanical action (abrasion, etc.) and — fire are not covered by ISO 12944. 1.3 The field of application is characterized by: — the type of structure, — the type of surface and surface preparation, — the type of environment, — the type of protective paint system, — the type of work and — the durability of the protective paint system. Although ISO 12944 does not cover all types of structure, surface and surface preparation, it may, by agreement, also be applied to those cases which are not covered by the standard. The various aspects of the field of application are described in more detail in 1.3.1 to 1.3.6. 1.3.1 Type of structure ISO 12944 concerns structures made of carbon or low-alloy steel (e.g. in accordance with EN 10025) of not less than 3 mm thickness, which are designed using an approved strength calculation. Not covered by ISO 12944 are concrete structures reinforced with steel. 1.3.2 Type of surface and surface preparation ISO 12944 deals with the following types of surface consisting of carbon or low-alloy steel, and their preparation: — uncoated surfaces; — surfaces thermally sprayed with zinc, aluminium or their alloys; — hot-dip-galvanized surfaces; — zinc-electroplated surfaces; — sherardized surfaces; — surfaces painted with prefabrication primer; — other painted surfaces. 1.3.3 Type of environment ISO 12944 deals with: — six corrosivity categories for atmospheric environments, — three categories for structures immersed in water or buried in soil. 1.3.4 Type of protective paint system ISO 12944 covers a range of paint products which dry or cure at ambient conditions. Not covered by ISO 12944 are: — powder coating materials, — stoving enamels, — heat-cured paints, — coatings of more than 2 mm dry-film thickness, — linings of tanks, — products for the chemical treatment of surfaces (e.g. phosphating solutions). 1.3.5 Type of work ISO 12944 covers both new work and maintenance. 1.3.6 Durability of the protective paint system ISO 12944 considers three different durability ranges (low, medium and high). See 3.5 and clause 4. The durability range is not a "guarantee time".

Paints and varnishes -- Corrosion protection of steel structures by protective paint systems -- Part 1: General introduction

KS M ISO 19840-2013(2018) 色漆和清漆ㅡ用防护涂料系统对钢结构的防腐ㅡ粗糙表面干膜厚度的测量和验收标准

Paints and varnishes ㅡ Corrosion protection of steel structures by protective paint systems ㅡ Measurement of, and acceptance criteria for, the thickness of dry films on rough surfaces

KS M ISO 12944-5:2013 涂料和清漆.防护漆体系对钢结构的腐蚀防护.第5部分:防护漆体系

이 표준은 강철 구조물의 부식 방지를 위해 일반적으로 사용되는 도료와 도료 시스템의 유형에 대하여 설명한다. 또한 다른 환경(KS M ISO 12944-2 참조)과 표면 처리 등급(KS M ISO 12944-4 참조)및 요구되는 내구성(KS M ISO 12944-1 참조)에 적합한 도료 시스템을 선정하는 지침도 제공한다.도료 시스템의 내구성은 저, 중, 고의 용어로 구분된다.

Paints and varnishes — Corrosion protection of steel structures by protective paint systems — Part 5: Protective paint systems

KS M ISO 19840:2013 涂料和清漆.基于防护漆系统的钢结构腐蚀防护.粗面干膜厚度的测量和验收标准

이 표준은 사용한 측정기 조정, 검사 영역의 정의, 시료 채취 계획, 측정 방법, 수용/거절 기준을 포함하며, 거친 표면에서 지정 건조 도막 두께를 검증하는 절차에 대하여 규정한다.이 표준의 목적을 위해, 규정된 두께는 KS M ISO 12944-5에 정의된 지정된 수치를 적용하고, 건조도막 두께는 대개 표면 조도의 고점 높이 위의 두께를 이용한다.이 표준에서 설명하는 절차는 영구 자석과 전자석 및 와전류식 유형의 측정기 사용에 근거한다. 측정기 정확도는 매끄러운 표면에서의 영점과 알고 있는 두께로 확인하고 필요하면 조정한다.그러므로 거친 강철 소지의 도막에서 측정한 결과는 표면 조도에서 고점 높이 위의 실제값보다 크다.표면 조도의 고점 높이 위의 건조 도막 두께는 기기 판독 수치에서 적절한 보정값을 뺀 수치로 정의한다.건조 도막 두께는 매끄럽고 평평한 강철 표면에서 조정된 판독 수치에 적절한 보정값을 적용하여 얻을 수 있다.보정값을 사용하지 않고 매끄럽고 평평한 강철 표면에서 조정된 개별 판독 수치를 규정하거나 합의할 경우, 이 방법은 이 표준에 적합하지 않다는 점을 인정하는 것이 중요하다.이 표준은 지정 건조 도막 두께가 40 .m 이상일 경우에 적용할 수 있다.

Paints and varnishes ㅡ Corrosion protection of steel structures by protective paint systems ㅡ Measurement of, and acceptance criteria for, the thickness of dry films on rough surfaces

KS M ISO 12944-5-2013(2018) 油漆和清漆 - 防腐涂料系统对钢结构的腐蚀保护 - 第5部分:防护漆系统

Paints and varnishes — Corrosion protection of steel structures by protective paint systems — Part 5: Protective paint systems

GSO ISO 12944-3:2013 油漆和清漆 通过保护漆系统保护钢结构免受腐蚀 第3部分：设计考虑因素

  Scope is not provided for this standard

Paints and varnishes - Corrosion protection of steel structures by protective paint systems - Part 3: Design considerations

GSO ISO 16276-2:2013 通过保护涂层系统保护钢结构免受腐蚀 涂层附着力/内聚力（撕裂强度）的评估和验收标准 第2部分：划格测试和切割测试 (X)

This part of ISO 16276 specifies procedures for rating the resistance of coating systems when a cut in the form of a right-angle lattice pattern (cross-cut) or in the form of an X (X-cut) is made into the coating, penetrating through to the substrate. This part of ISO 16276 is only applicable if the cross-cut or X-cut test method is specified, together with the rating from the appropriate rating scale. NOTE The characteristics of the coating can make the assessment of the result of a cross-cut or X-cut test difficult. This part of ISO 16276 also specifies suitable equipment and defines inspection areas, sampling plans and acceptance/rejection criteria. It does not specify ratings for particular coating systems.

Corrosion protection of steel structures by protective paint systems – Assessment of, and acceptance criteria for, the adhesion/cohesion (fracture strength) of a coating – Part 2: Cross-cut testing and X-cut testing

GSO ISO 15741:2013 油漆和清漆 摩擦 钢管的内部和外部涂层 减少非腐蚀性气体

  Scope is not provided for this standard

Paints and varnishes – Friction-reduction coatings for the interior of on- and offshore steel pipelines for non-corrosive gases

DS/ISO 19840:2012 油漆和清漆 保护漆系统对钢结构的腐蚀防护 粗糙表面干膜厚度的测量和验收标准

This International Standard specifies a procedure for the verification of dry-film thickness against nominal dryfilm thickness on rough surfaces, including the adjustment of the instruments used, the definition of inspection areas, sampling plans, measure

Paints and varnishes - Corrosion protection of steel structures by protective paint systems - Measurement of, and acceptance criteria for, the thickness of dry films on rough surfaces

ISO 19840:2012 涂料和清漆.用防护漆系统对钢结构的腐蚀防护.粗糙表面上干膜厚度的测量和验收标准

This International Standard specifies a procedure for the verification of dry-film thickness against nominal dryfilm thickness on rough surfaces, including the adjustment of the instruments used, the definition of inspection areas, sampling plans, measurement methods and acceptance/rejection criteria. For the purposes of this standard, any specified thickness is taken to be nominal as defined in ISO 12944-5, and the dry-film thickness is the typical thickness above the peaks of the surface profile. The procedure described in this International Standard is based on the use of instruments of the permanent magnet, electromagnet and eddy current type. Instrument accuracy is verified both at zero and at a known thickness on a smooth surface and adjusted if necessary. Measurements taken on a coating on a roughened steel substrate will therefore be higher than the actual value above the peaks of the profile. The thickness of the dry film above the peaks of the profile is defined as the instrument reading minus an appropriate correction value. The dry-film thickness is obtained by using the appropriate correction value applied to readings based on adjustment on a smooth, flat steel surface. Where individual readings, based on adjustment on a smooth, flat steel surface without the use of correction values, are specified or agreed, it is important to recognize that this method does not conform with this International Standard. This standard is applicable if the nominal dry-film thickness is 40 µm or greater.

Paints and varnishes - Corrosion protection of steel structures by protective paint systems - Measurement of, and acceptance criteria for, the thickness of dry films on rough surfaces

SNI ISO 12944-6:2012 油漆和清漆 防护漆系统对钢结构的腐蚀保护 第6部分：实验室性能测试方法

Paints and varnishes - Corrosion protection of steel structures by protective paint systems-Part 6: Laboratory performance test methods

SNI ISO 12944-5:2012 油漆和清漆 用防护漆系统对钢结构进行腐蚀保护 第5部分：防护漆系统

Cat dan pernis - perlindungan dari korosi pada struktur baja dengan sistem pengecatan pelindung - Bagian 5: Sistem pengecatan pelindung

LST EN ISO 29601:2011 油漆和清漆 防护漆系统的腐蚀保护 干膜孔隙率评估（ISO 29601:2011）

Paints and varnishes - Corrosion protection by protective paint systems - Assessment of porosity in a dry film (ISO 29601:2011)

DS/EN ISO 29601:2011 油漆和清漆 防护漆系统的腐蚀防护 干膜中孔隙率的评估

ISO 29601:2011 specifies procedures for detecting the presence of porosity in a protective paint system of any thickness on a steel or other metallic substrate. The procedures given are based on methods using two different types of test equipment, the choice of equipment depending on the dry film thickness. These procedures are only applicable to the testing of electrically non-conductive parts of a paint system.The test methods specified are mainly intended for use with new coatings, but can also be used for coatings which have been in service for some time. In the latter case, it is important to bear in mind that the coating might have been penetrated by

Paints and varnishes - Corrosion protection by protective paint systems - Assessment of porosity in a dry film

BS EN ISO 29601:2011 涂料和清漆.用防护漆系统防腐蚀.干膜中孔隙率的评定

This International Standard specifies procedures for detecting the presence of porosity in a protective paint system of any thickness on a steel or other metallic substrate. The procedures given in this International Standard are based on methods using two different types of test equipment, the choice of equipment depending on the dry film thickness. These procedures are only applicable to the testing of electrically nonconductive parts of a paint system. The test methods specified are mainly intended for use with new coatings, but can also be used for coatings which have been in service for some time. In the latter case, it is important to bear in mind that the coating might have been penetrated by substances in contact with the coating during service.

Paints and varnishes. Corrosion protection by protective paint systems. Assessment of porosity in a dry film

ISO 29601:2011 涂料和清漆.防护漆体系的防腐蚀.干膜内多孔性的评价

This International Standard specifies procedures for detecting the presence of porosity in a protective paint system of any thickness on a steel or other metallic substrate. The procedures given in this International Standard are based on methods using two different types of test equipment, the choice of equipment depending on the dry film thickness. These procedures are only applicable to the testing of electrically nonconductive parts of a paint system. The test methods specified are mainly intended for use with new coatings, but can also be used for coatings which have been in service for some time. In the latter case, it is important to bear in mind that the coating might have been penetrated by substances in contact with the coating during service.

Paints and varnishes - Corrosion protection by protective paint systems - Assessment of porosity in a dry film