87.060.20 涂料粘合剂 标准查询与下载

GSO ISO 10283:2015 色漆和清漆用粘合剂异氰酸酯树脂中单二异氰酸酯的测定

This International Standard specifies a gas-chromatographic method for determining monomeric diisocyanates such as toluene diisocyanate1), hexamethylene diisocyanate, isophorone diisocyanate2), diphenylmethane diisocyanate3) and other diisocyanates in isocyanate resins as defined in Clause 3 and in solutions prepared from such resins, insofar as these are used in the formulation of paints and similar coating materials.

Binders for paints and varnishes -- Determination of monomeric diisocyanates in isocyanate resins

GSO ISO 6271-2:2015 透明液体 用铂钴标尺估算颜色 第2部分：分光光度法

This part of ISO 6271 specifies a spectrophotometric method for estimating the colour, in Pt-Co units, of clear liquids. It is applicable to clear liquids having a colour characteristic similar to those of the reference platinum-cobalt scale specified in ISO 6271-1. The method described provides a more precise way of measuring Pt-Co colour than that described in ISO 6271-1. NOTE The term “platinum-cobalt colour (Pt-Co colour)” used here is preferred over the terms “Hazen colour” and “APHA colour”.

Clear liquids -- Estimation of colour by the platinum-cobalt scale -- Part 2: Spectrophotometric method

GSO ISO 6744-1:2015 油漆和清漆用基料 醇酸树脂 第1部分：通用测试方法

This part of ISO 6744 describes general methods of test for alkyd resins for use in paints, varnishes and similar products. It is also applicable to those solutions and similar preparations made from alkyd resins that are intended for use as binders for paints and varnishes. The test methods to be used for an individual alkyd resin shall be the subject of agreement between the interested parties.

Binders for paints and varnishes -- Alkyd resins -- Part 1: General methods of test

GSO ISO 7143:2015 油漆和清漆用粘合剂 测定水性粘合剂性能的试验方法

This International Standard specifies methods of test for characterizing binders, i.e. aqueous dispersions and solutions of polymers and copolymers, in particular those used as raw materials for water-based coating materials. The properties determined will depend on whether a drying or curing system is tested.

Binders for paints and varnishes -- Methods of test for characterizing water-based binders

GSO ISO 7142:2015 粘合剂、油漆和清漆 环氧树脂 一般测试方法

This International Standard specifies general methods of test for epoxy resins for use in paints, varnishes and similar products. It is also applicable to those solutions made from epoxy resins that are intended for use as binders for paints and varnishes. The test methods to be applied to an individual epoxy resin shall be the subject of agreement between the interested parties. The test methods described in this International Standard are not intended for epoxy esters (see Note to 3.1).

Binders for paints and varnishes -- Epoxy resins -- General methods of test

GSO ISO 4630-1:2015 透明液体 加德纳色标测定颜色 第1部分：目视法

This part of ISO 4630 specifies a method for estimating, by means of the Gardner colour scale, the colour of clear, yellow/brown liquid products using colour-measuring instruments. The results might be invalid if other products are tested. It is applicable to drying oils, varnishes and solutions of fatty acids, polymerized fatty acids, resins, tall oil, tall oil fatty acids, rosin and related products. It is applicable to products having colours from Gardner 1 to Gardner 18. The Gardner scale is not applicable to products with colours lighter than 1 or darker than 18.

Clear liquids -- Estimation of colour by the Gardner colour scale -- Part 1: Visual method

GSO ISO 4625-1:2015 油漆和清漆用基料 延展点的测定 第1部分：环球法

This part of ISO 4625 specifies methods of determining the softening point of resins (including rosin) and similar materials by means of the ring-and-ball apparatus. Both manual and automatic methods are specified.

Binders for paints and varnishes -- Determination of softening point -- Part 1: Ring-and-ball method

GSO ISO 3681:2015 色漆和清漆用粘合剂皂化度的测定体积定量法

This International Standard specifies a titrimetric method for determining the esterified-acid content in binders for paints and varnishes, free acids and acid anhydrides being necessarily included in the result obtained. Because different binders vary in their resistance to saponification, this International Standard is of limited applicability. If necessary, completeness of saponification may be checked by repeating the test under more severe conditions achieved by the use of longer saponification time, more concentrated potassium hydroxide solution, or a higher-boiling alcohol as solvent. Annex A specifies a procedure suitable for binders that saponify with difficulty. The method is not applicable to those materials that show further reaction with alkalis beyond normal saponification.

Binders for paints and varnishes -- Determination of saponification value -- Titrimetric method

EN ISO 8623:2015 高油脂肪酸色漆和清漆.试验方法和特征值(ISO 8623:2015)

Diese Internationale Norm legt Prüfverfahren für destillierte Tallöl-Fettsäuren für Beschichtungsstoffe fest und gibt Informationen zu Kennwerten dieser Produkte an.

Tall-oil fatty acids for paints and varnishes - Test methods and characteristic values (ISO 8623:2015)

ASTM D509-15 松香取样和分级的标准试验方法

3.1 Rosin is an important product of the centuries old Naval Stores industry, now known as the Pine Chemical industry, and is produced and consumed in many countries throughout the world. Consequently, reliable methods of sampling and grading rosin are necessary. The test methods based on the use of the USDA Official Standards described herein, were developed many years ago for the sampling and grading of rosin and are similar to those included in the Naval Stores Act.3 3.2 Although these test methods based on the use of the USDA Official Standards are still applicable, many additional test methods are now used to grade rosin. In particular, the color of rosin is now more commonly reported using the Gardner color scale rather than the USDA Official Standards. In addition, Test Methods E28, D465, and D5974 are widely used to assess the quality of rosin in addition to the color grading methods described in this standard. 1.1 These test methods cover procedures for sampling and determining the grade of rosin delivered in commercial bags, barrels, drums or in molten form. Although developed for rosin, these methods can also be used for the grading of modified rosins and rosin based resins. Note 1: All rosin sold in interstate commerce must be described by reference to the U. S. Standards for rosin, and is therefore subject to grading prior to such sale. The grading procedure described in these test methods is used for checking grades or regrading after the rosin has moved from the primary markets to distributing or consuming points. 1.2 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Test Methods of Sampling and Grading Rosin

ASTM D1585-15 含松脂, 妥尔油的松木化学品及其相关产品的脂肪酸含量的标准试验方法

4.1 These test methods are designed to broaden the scope of the previous edition of these test methods by the inclusion of tall oil as a test material. Test Methods D803 currently includes methods for the determination of the rosin acid and fatty acid content of crude tall oil. Test Methods D803 references Test Method D1585. 4.2 Rosin and tall oil are composed primarily of rosin acids and fatty acids, and the measurement of these components is important in establishing the composition of these materials. 1.1 These test methods cover the determination of the fatty acids of pine chemicals, including rosin, tall oil, and related products. 1.2 These test methods may not be applicable to adducts or derivatives of rosin or other pine chemical products. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Test Methods for Fatty Acids Content of Pine Chemicals, Including Rosin, Tall Oil, and Related Products

ASTM D465-15 含妥尔油的松木化学产品及其他相关产品酸性值的标准试验方法

3.1 These test methods are designed to broaden the scope of the earlier editions of the test method by the inclusion of tall oil and tall oil derived products as test materials and will be referenced in Test Methods D803. 3.2 The acid number is an important property of pine chemical products, such as tall oil, and the products obtained by the fractionation of tall oil. It is the test method widely used to determine the total free acid content of these products. 3.3 The potentiometric test method should be used when the most reproducible results are required. 1.1 These test methods are intended for determining the acid number of pine chemical products as defined in Terminology D804 including tall oil products, wood and gum rosin, and other related materials. These test methods may not be applicable to all modified rosin products. Two test methods are covered, as follows: 1.1.1 Potentiometric method (referee), and 1.1.2 Internal indicator method (alternate). 1.2 The potentiometric method is suitable for use with both light- and dark-colored products. It should be considered the referee method. The internal indicator method is suitable for use only with light- and medium-colored products with a Gardner color of less than 12. It should be considered the alternate method. 1.3 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Test Methods for Acid Number of Pine Chemical Products Including Tall Oil and Other Related Products

ASTM D464-15 含妥尔油的松木化学产品及其他相关产品皂化值的标准试验方法

3.1 These test methods are designed to broaden the scope of the earlier editions of the test method by the inclusion of tall oil and tall oil derived products as test materials and is referenced in Test Methods D803. 3.2 The saponification number is an important property of tall oil and the products obtained by the fractionation of tall oil. It is the test method widely used to determine the total acid content, both free and combined, of these products. 3.3 The potentiometric test method should be used when the most reproducible results are required. 1.1 These test methods cover the determination of the saponification number of tall oil and products obtained by the fractionation of tall oil such as rosin, fatty acids and distilled tall oil as defined in Terminology D804. These test methods are also applicable to gum and wood rosin. Two test methods are covered as follows: 1.1.1 Test method using a potentiometric method, and 1.1.2 Test method using an internal indicator method. 1.2 The potentiometric method is suitable for use with both light- and dark-colored test samples. It should be considered the referee method. The internal indicator method is suitable for use only with light- and medium-colored test samples. It should be considered the alternate method. 1.3 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Test Methods for Saponification Number of Pine Chemical Products Including Tall Oil and Other Related Products

ASTM D803-15 妥尔油测试的标准试验方法

3.1 Tall oil, both crude and refined, is an important by-product of the alkaline (kraft) pulping of pine wood. It consists primarily of fatty acids, resin acids, and neutral materials; the levels of these various components depend on factors such as the species of pine tree, geographic location, climate, etc. 3.1.1 Tall oil is used primarily as a commercial source of fatty acids and rosin, and, therefore, reliable methods for the analysis of these components is necessary. 1.1 These test methods cover the test procedures to be applied to whole tall oils or refined tall oils. Previous editions of these test methods have described test procedures that are used to test tall oil fatty acid, rosin, and other tall oil-derived products as well as test crude and refined tall oil. Consequently, these test methods are widely cited in reference books and industry literature for the testing of tall oil-derived products. 1.1.1 In this current revision, procedural details of some of the often-cited test methods have been removed and the test methods consolidated with other existing test methods. In such cases the consolidated methods, applicable to all tall oil-derived products. 1.2 The procedures appear in the following order: Physical Tests Sections Viscosity:   8199;Rotational Viscometer Method (Preferred Method)  7 8199;Bubble Time Method  8 Flash Point  9 Color 10 Moisture: 11 8199;Insoluble Matter

Standard Test Methods for Testing Tall Oil

HG/T 4763-2014 涂料用醇酸树脂

本标准规定了涂料用醇酸树脂的要求，试验方法，检验规则，标志、包装和贮存等内容。 本标准适用于由多元酸和脂肪酸(或油)与多元醇缩聚而成的涂料用溶剂型醇酸树脂。本标准也适用于为获得特定的性能而改性的涂料用醇酸树脂，常用的改性剂包括松香、酚醛树脂、苯乙烯、异氰酸酯、聚酰胺、丙烯酸、环氧树脂或有机硅化合物等。

Alkyd resin for coatings

HG/T 4765-2014 涂料用环氧树脂

本标准规定了涂料用环氧树脂的产品分等，要求，试验方法，检验规则以及标志、包装和贮存等内容。 本标准适用于液体涂料用环氧树脂。

Epoxy resin for coatings

GSO ISO 11908:2013 有助于油漆和清漆粘合的材料 氨基树脂 一般测试方法

This International Standard details general test methods for amino resins and solutions of amino resins intended for use as binders in paints, varnishes and related products.

Binders for paints and varnishes -- Amino resins -- General methods of test

GSO ISO 11668:2013 油漆和清漆用基料 氯化聚合物树脂 通用试验方法

This International Standard describes general methods of test for a) chlorinated rubber and b) vinyl chloride copolymers for use in paints, varnishes and similar products. The test methods to be applied in each individual case shall be the subject of agreement between the interested parties.

Binders for paints and varnishes -- Chlorinated polymerization resins -- General methods of test

GSO ISO 13885-1:2013 油漆和清漆用基料 颜色渗透凝胶 第1部分：四氢呋喃乳液

This part of ISO 13885 describes the determination of the molar-mass distribution, number-average molar mass Mn and mass-average molar mass Mw of polymers that are soluble in THF (tetrahydrofuran) by gel permeation chromatography (GPC)1). It is possible that, in spite of the good repeatability obtained with this method, it cannot be used with certain polymer types because of specific interactions, such as adsorption within the sample/eluent/column system. The method is not an absolute one and requires calibration with commercially available unbranched-polystyrene standards that have been characterized by absolute methods. The results for samples of polymers other than polystyrene are therefore only comparable within groups of samples of the same type. The conditions specified in this part of ISO 13885 are not suitable for the GPC analysis of polymer samples with Mw values greater than 106 (see Annex C). No correction methods, e.g. for the elimination of peak broadening, are included in this part of ISO 13885. If absolute molar-mass values are required, an absolute method, e.g. membrane osmometry for Mn or light scattering for Mw, must be used.

Binders for paints and varnishes -- Gel permeation chromatography (GPC) -- Part 1: Tetrahydrofuran (THF) as eluent

GSO ISO 11909:2013 油漆和清漆用基料—聚异氰脲酸酯树脂—通用试验方法

This International Standard details general test methods for polyisocyanate resins and solutions of polyisocyanate resins intended for use as binders in paints, varnishes and related products.

Binders for paints and varnishes -- Polyisocyanate resins -- General methods of test