91.060.01 建筑构件综合 标准查询与下载

ASTM D7089-06(2014) 采用压力冲洗法测定水泥, 砖石和天然石料表面的除涂鸦覆盖层有效性的标准实践规程

5.1 Graffiti on buildings and structures is a significant problem in various regions across the country. A variety of coatings have been developed to be either resistant to the application of paints/marker or to aid in their removal. This standard practice describes a procedure for evaluating the effectiveness of anti-graffiti coatings applied to various concrete, masonry and natural stone substrates. It does not address graffiti removal on metal or any other non-mineral substrate. 5.2 This practice only addresses graffiti removal on substrates in a laboratory environment, that have not been exposed to either natural or artificial weathering. Specification D6578 describes a method for graffiti removal after both natural and artificial weathering. 1.1 This practice covers a basic method for evaluating the performance of anti-graffiti products on mineral building substrates by a series of increasingly abrasive cleaning methods. The anti-graffiti materials are applied to a series of concrete, masonry and natural stone specimens for evaluation. Graffiti resistance is based on how a defined set of markings are removed by a designated set of cleaning techniques. 1.2 This practice also defines a procedure to evaluate graffiti removal after re-marking with subsequent re-cleaning. It does not address the re-treatment of substrates after a material is no longer graffiti resistant. 1.3 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Practice for Determination of the Effectiveness of Anti-Graffiti Coating for Use on Concrete, Masonry and Natural Stone Surfaces by Pressure Washing

CECS 176-2005 聚丙烯复合塑料隔离护栏应用技术规程

本规程适用于城市新建、改建道路工程的车行道、人行道隔离护栏等工程的设计、施工及验收。其他市政工程、园林绿地、居住小区和工业园区隔离护栏工程的设计、施工及验收，可参照本规程的规定执行。

Technical specification for application of PP-N plastic fence

CECS 176-2005（条文说明） 聚丙烯复合塑料隔离护栏应用技术规程

Technical specification for application of PP-N plastic fence

CECS 158-2004 膜结构技术规程

本规程适用于膜结构的设计、制作、安装、验收及维护。 本规程遵照现行国家标准《建筑结构可靠度设计统一标准》GB 50068规定的原则，根据现行国家标准《建筑结构荷载规范》GB 50009、《钢结构设计规范》GB 50017、《冷弯薄壁型钢结构技术规范》GB 50018、《钢结构工程施工质量验收规范》GB 50205的有关规定，并结合膜结构的特点面编制。

Technical specification for membrane structures

CECS 01-2004 呋喃树脂防腐蚀工程技术规程

本规程适用于呋喃树脂防腐蚀工程的设计、施工及验收。

Technical specification for anticorrosion engineering with furan resin

ASTM E529-04(2011) 进行房屋建筑用桁条和大梁弯曲试验的标准指南

1.1 This guide covers the flexural testing of beams and girders under simulated service conditions to determine their structural performance characteristics. Methods following this guide are intended primarily for constructions that may not conform with the relatively simple assumptions upon which well-known flexural theories are based. In some cases, they are also suitable for determining the structural adequacy of the design, materials, connections, and fabrication techniques. The methods are not intended for use in routine quality control tests. 1.2 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. For specific precautionary statement, see 7.1.

Standard Guide for Conducting Flexural Tests on Beams and Girders for Building Construction

DS/CWA 14646:2003 结构预应力后张预应力套件的安装要求和专业公司及其人员的资质

This document specifies common provisions for the installation of post-tensioning kits for prestressing of structures including the qualification of the PT specialist company and its personnel undertaking such works.

Requirements for the installation of post-tensioning kits for prestressing of structures and qualification of the specialist company and its personnel

JGJ 61-2003 网壳结构技术规程

Technical specification for latticed shells

ASTM E695-03(2015)e1 测量墙, 楼板和屋顶建筑的相对抗冲击负荷的标准试验方法

4.1 The procedures outlined will provide data that can be used to evaluate the relative performance of wall, floor, and roof constructions under conditions representative of those sustained in actual service when subjected to impact by a heavy blunt object. See Test Method E661 for evaluation of floor and roof sheathing and Practice E73 for evaluation of roof trusses. 4.2 The method is intended to be applied to relatively light construction, including, but not limited to, wood floor and roof systems, partitions framed with wood or steel studs, steel floor or roof decking systems, steel siding and wall panels, or thin concrete and masonry walls or slabs and similar assemblies. 1.1 This test method covers the measurement of the relative resistance of wall, floor, and roof construction to impact loading. The test is not applicable to doors. 1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Test Method of Measuring Relative Resistance of Wall, Floor, and Roof Construction to Impact Loading

DB15/T 373-2002 冷轧带肋钢筋混凝土楼板配筋代换表

本代换表只适用以普通低碳钢或低合钢热轧圆盘条为母材，经冷轧减径后，在其表面冷轧成具有三面或两面月牙形横肋的钢筋。本代换表适用于不直接承受重复荷载的工业与民用建筑的普通钢筋混凝土楼板。本代换表适用于I级钢配筋及冷轧带肋钢筋配筋之间的相互代换；亦适用于不同直径冷轧带肋钢筋之间及采用单筋配筋与并筋（不超过两根）配筋之间的相互代换。

substitution table into equivalent cold rolled ribbed steel wires & bars for on-site-cast floor & ceiling plates

SJ/T 11236-2001 防静电贴面板通用规范

本规范委托信息产业部电子工业标准化研究所负责解释。 本规范规定了防静电贴面板的分类与命名、技术要求、试验方法、质量评定程序和标志、包装、贮存、运输等要求。 本规范适用于PVC热塑性防静电贴面板和三聚氰胺热固性防静电贴面板，其他防静电贴面板可参照使用。

General specification for electrostatic protection covers

CECS 18-2000 聚合物水泥砂浆防腐蚀工程技术规程

本规程适用于氯丁胶乳水泥砂浆和聚丙烯酸酯乳液水泥砂浆防腐蚀工程的设计、施工及验收。 采用其它品种的聚合物水泥砂浆时，应经试验确定。

Technical specification for anticorrosion works of polymer cement mortar

CECS 116-2000 钾水玻璃防腐蚀工程技术规程

本规程适用于钾水玻璃防腐蚀工程的设计、施工及验收。

Technical specification for anticorrosion engineering of potassium silicate

CECS 101-1998 建筑瓷板装饰工程技术规程

本规程适用于工业与民用建筑的瓷板装饰工程设计、施工及验收。

Specification for building porcelain decorative engineering

ASTM E529-94(1998)e1 建筑结构用梁和大梁弯曲试验的标准指南

Standard Guide for Conducting Flexural Tests on Beams and Girders for Building Construction

TIS 1417-1997 大理石板

Marble slabs

ASTM E695-79(1997)e1 测量墙壁、地板和屋顶结构对冲击荷载的相对阻力的标准方法

Standard Method for Measuring Relative Resistance of Wall, Floor, and Roof Construction to Impact Loading

HJ/T 17-1996 隔声窗

本技术条件规定了隔声窗产品的技术性能及检验方法。 本技术条件适用于各种隔声窗产品。

Windows for sound insulation

GA/T 143-1996 金库门通用技术条件

General technical conditions for treasury gates

BS 6093:1993 建筑结构的接缝及连接设计实用规程

Draws attention to the design processes and mechanisms of a broad range of basic jointing methods, to assist designers in solving problems for specific designs. Recommendations are made on the use of sealants and gaskets.

Code of practice for design of joints and jointing in building construction