91.060.50 门窗 标准查询与下载

KS F 2638-2022 门、窗、百叶窗抗侵入性试验方法 静载抵抗力

Intrusion resistance test method for door, windows, shutters－Resistance under static loading

KS F 2637-2022 门、窗、百叶窗抗侵入试验方法 动载抵抗力

Intrusion resistance test method for doors, windows, shutters－Resistance under dynamic loading

KS F 1514-2022 建筑楼板构件标准公称尺寸

Standard nominal dimension of floor components for building

ASTM E2068-00(2022) 滑动门窗操作力测定的标准试验方法

1.1 This test method determines the operating forces for opening and closing horizontal and vertical sliding windows and horizontal sliding door systems. It does not address the forces required for opening pivoting, projecting, or other fenestration systems. This test method does not address the use or performance of add-on devices or mechanical operators that might be installed to reduce operating forces of sliding windows or doors. It deals only with the forces necessary to open and close a sash or panel through the direct application of force to the operable sash or panel. 1.2 This test method is suitable for laboratory product comparisons or for qualifying products, or both, as meeting window or door operating force specifications. This test method is also suitable for use in the field to determine the operating forces required to open and close installed sliding windows and doors. 1.3 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. For specific precautionary statements, see Section 7. 1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Method for Determination of Operating Force of Sliding Windows and Doors

ASTM E1424-22 通过外部窗户 幕墙和门的空气泄漏速率的标准测试方法在样本下的指定压力和温度差异

1.1 This test method provides a standard laboratory procedure for determining the air leakage rates of exterior windows, curtain walls, and doors under specified differential air temperature and pressure conditions across the specimen. 1.2 Specified temperature and pressure conditions are representative of those that may be encountered at the exterior thermal envelope of buildings, excluding the effects of heat buildup due to solar radiation. 1.3 This laboratory procedure is applicable to exterior windows, curtain walls, and doors and is intended to measure only such leakage associated with the assembly and not the installation; however, the test method can be adapted for the latter purpose. 1.4 This is a laboratory procedure for testing at differential temperature conditions. Persons interested in a laboratory test at ambient conditions should reference Test Method E283. Persons interested in a field test on installed windows and doors should reference Test Method E783. 1.5 Persons using this procedure should be knowledgeable in the areas of heat transfer, fluid mechanics, and instrumentation practices, and shall have a general understanding of fenestration products and components. 1.6 The values stated in SI units are to be regarded as standard. The values given in parentheses after SI units are provided for information only and are not considered standard. 1.7 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. For specific hazard statements, see Section 7. 1.8 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Method for Determining the Rate of Air Leakage Through Exterior Windows, Skylights, Curtain Walls, and Doors Under Specified Pressure and Temperature Differences Across the Specimen

CSA A440.2-2022 开窗能源性能/CSA A440.2:22 用户指南 开窗能源性能

1 Scope 1.1 General This Standard applies to a) fenestration systems covered by AAMA/WDMA/CSA 101/I.S.2/A440, including i) vertically sliding windows; ii) horizontally sliding windows; iii) dual-action windows; iv) casement windows, both fixed and operable; v) projecting (awning/hopper) windows; vi) fixed windows; vii) sidelites; viii) transom windows; ix) sliding doors; x) side-hinged doors; xi) dual-action side-hinged doors; xii) architectural terrace doors; xiii) unit skylights and roof windows; xiv) greenhouse or garden windows; and xv) tubular daylighting devices; b) curtain walls, window walls, and storefront; and c) garage (vehicular access/rolling) doors. Note: Unless otherwise specified, the term “fenestration system” is used to apply to all products listed in Clause 1.1. 1.2 Application This Standard specifies both measurement and computer simulation methods for establishing the following fenestration system properties for both residential and commercial applications: a) overall coefficient of heat transfer (U-factor); b) solar heat gain coefficient (SHGC); c) visible transmittance (VT); and d) Temperature Index (I) and Condensation Index (CI). Note: The fenestration properties established in accordance with this Standard are for specific indoor and outdoor conditions and will vary slightly under actual conditions. The values obtained by the methods specified in this Standard are considered to provide an acceptable basis for comparing performance in use. 1.3 Energy Rating (ER) 1.3.1 This Standard specifies a method for determining an energy performance rating for vertical fenestration systems, under heating conditions, for use in low-rise residential applications. The Energy Rating (ER) includes factors for a) solar heat gain; b) heat loss by conduction, radiation, and convection; and c) heat loss by air leakage. 1.3.2 The ER allows for a comparison of different fenestration systems on the basis of their effect on the energy supplied annually by the heating system. The ER calculation assumes vertical installation in low-rise residential buildings and is based on average conditions for a) incident solar radiation on fenestration systems facing the four cardinal compass directions (north, east, south, and west); and b) representative climate zones in Canada. 1.3.3 The ER should not be used to rate a) any sloped glazing (residential or commercial); or b) fenestration products that will be installed in commercial, industrial, or high-rise residential buildings. 1.4 A440.3 general information CSA A440.3 is a user guide to this Standard. It provides guidance on determining a) a specific Energy Rating (ERS) for particular locations, orientations, and vertical fenestration system sizes; and b) an ER for residential cooling (ERC). 1.5 Annex B general information Annex B introduces the issue of climate change and its associated effects on fenestration in buildings. It is anticipated that fenestration designers will need to incorporate changes in climate loads resulting from climate change into fenestration product design. It is also anticipated that adjustments will need to be made to installation detailing. Annex B provides some information on these topics for consideration by building design professionals, authorities having jurisdiction, and installers. As information on climate change evolves, so too will the requirements of this Standard. 1.6 Exceptions This Standard does not apply to a) fixed glazing cast into precast concrete panels; b) revolving doors; c) doors intended for indoor use; d) storm doors; and e) glazed architectural structures. Note: While these products have not been considered in the development of this Standard, simulation procedures given in the Standard may be used to evaluate the U-factor and the SHGC of these products. This Standard does not address the retention of thermal and optical properties and airtightness by fenestration systems over time and under conditions of use. 1.7 Terminology In this Standard, “shall” is used to express a requirement, i.e., a provision that the user is obliged to satisfy in order to comply with the Standard; “should” is used to express a recommendation or that which is advised but not required; and “may” is used to express an option or that which is permissible within the limits of the Standard. Notes accompanying clauses do not include requirements or alternative requirements; the purpose of a note accompanying a clause is to separate from the text explanatory or informative material. Notes to tables and figures are considered part of the table or figure and may be written as requirements. Legends to equations and figures are considered requirements. Annexes are designated normative (mandatory) or informative (non-mandatory) to define their application.

Fenestration energy performance/User Guide to CSA A440.2:22, Fenestration energy performance

T/CASME 36-2022 建筑用防火钢百叶窗

本文件规定了建筑用防火钢百叶窗的术语和定义、分类、技术要求、试验方法、检验规则和标志、合格证书、包装、运输及贮存。

Fireproof steel louver for building

KS F 4534-2022 窗扇配件

Fittings for sash windows

KS F 3128-2022 车门蒙皮

Door skin

JC/T 2650-2022 平衡门

本文件规定了平衡门的分类、规格和标记、材料与配件、一般要求、要求、试验方法、检验规则、标志、包装、运输和贮存。 本文件适用于工业与民用建筑中的平衡门。

Balance door

KS F 2275-2022 铰链性能试验

Performance test of hinges

T/WJZP 004-2022 装配式箱房专用铝合金窗

6.1　外观 6.2　尺寸 6.3　组装 6.4　五金配件安装 6.5　物理性能：启闭力、抗对角线变形性能

Special aluminum alloy window for assembly container house

T/WJZP 002-2022 装配式箱房专用门

6.1　外观 6.2　加工制作 6.3　五金配件安装 6.4　防腐 6.5　性能要求：气密性能、水密性能、抗风压性能

Special door for assembly container house

T/WJZP 005-2022 装配式箱房专用塑料窗

6.1　外观 6.2　尺寸 6.3　装配 6.4　物理性能：气密性能、水密性能、抗风压性能 6.5　力学性能：锁闭器开关力、窗的开关力、弯曲、反复启闭性能

Special plastic window for assembly container house

T/CASME 15-2022 智能限位式工业滑升门开门机

本文件规定了智能限位式工业滑升门开门机（以下简称“开门机”）的术语和定义、分类与规格、使用环境、技术要求、试验方法、检验规则、标志、包装、运输、贮存。

Intelligent limit industrial sliding door opener

T/FSNZ 14-2022 铝合金安防一体窗

铝合金安防一体窗（以下简称：一体窗）的术语和定义、分类、规格和标记、要求、试验方法、检验规则、标志及随行文件、包装、运输和贮存。

Aluminum alloy security integrated window

DB11/T 1832.8-2022 建筑工程施工工艺规程 第8部分：门窗工程

Construction technology specification for building engineering Part 8: Door and window engineering

T/CECS 1143-2022 定制门窗工程技术规程

本规程共分10章，主要内容包括：总则、术语、基本规定、建筑对门窗的定制要求、材料、定制门窗设计、加工制作、安装、验收、使用和维护。

Customized doors and windows engineering technical regulations

ASTM E2319-22 在试样上规定的压差下测定通过外窗、幕墙和门的表面和侧面的气流的标准试验方法

1.1 This test method is a modified version of Test Method E283/E283M, and provides a standard laboratory procedure for determining air leakage separately through the face and sides of exterior windows, curtain walls, and doors under specified differential pressure conditions across the specimen. The test method described is for tests with constant temperature and humidity across the specimen. NOTE 1—Detailing buildings with continuous air barriers requires that the air barrier plane in a window system be clearly defined. When special circumstances dictate that the air barrier be sealed to the window frame at a location other than that used to seal the specimen to the test chamber in this test method, additional laboratory testing may be required to clarify potential paths of air flow through the sides of the window frame. The adapted testing procedure described herein is intended for this purpose. 1.2 This laboratory procedure is applicable to exterior windows, curtain walls, and doors and is intended to measure only such leakage associated with the assembly and not the installation. The test method can be adapted for the latter purpose. NOTE 2—Performing tests at non-ambient conditions or with a temperature differential across the specimen may affect the air leakage rate. This is not addressed by this test method. 1.3 This test method is intended for laboratory use. Persons interested in performing field air leakage tests on installed units should reference Test Method E783. Test Method E783 will not provide the user with a means of determining air flow through the sides of tested specimens. 1.4 Persons using this procedure should be knowledgeable in the areas of fluid mechanics, instrumentation practices, and shall have a general understanding of fenestration products and components. 1.5 The values stated in SI units are to be regarded as standard. The values given in parentheses are mathematical conversions to inch-pound units that are provided for information only and are not considered standard. 1.6 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. For specific hazard statement see Section 7. 1.7 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Method for Determining Air Flow Through the Face and Sides of Exterior Windows, Curtain Walls, and Doors Under Specified Pressure Differences Across the Specimen

T/ZZB 0179-2022 木质复合免漆门

本文件规定了木质复合免漆门的术语和定义、基本要求、技术要求、试验方法、检验规则、标志、 使用说明、包装、运输和贮存及质量承诺。 本文件适用于以表面覆贴PVC的木质复合免漆门。

Paint-free wood composite door