91.080.01 建筑结构综合 标准查询与下载

KS F ISO 4354-2021 风对结构的作用

Wind actions on structures

T/SHMHZQ 101-2021 展台设计技术规范

4 基本原则  4.1 简约化  4.2 模块化  4.3 低碳化  4.4 安全化  5 设计要求  5.1 展台主体  5.2 电气设备  6 总体设计  6.1 外观  6.2 功能  6.3 性能  6.4 主题  6.5 艺术性  7 细节设计  7.1 平面规划  7.2 空间格局  7.3 信息分布  7.4 色彩运用、造型设计  7.5 灯光设计  7.6 电气设计 7.7 影音设计  7.8 装饰物设计

Technical specification for booth design

BS ISO 15928-7:2021 房屋 性能说明 可访问性和可用性

Houses. Description of performance. Accessibility and usability

DB32/T 4065-2021 建筑幕墙工程技术标准

本标准适用于江苏省新建、改建及扩建民用建筑用建筑幕墙、采光顶与金属屋面工程的设计、制作、安装施工、检测、工程验收以及维修保养

Technical Standards for Building Curtain Wall Engineering

T/GIDA 001-2021 室内装饰设计规范

本文件规定了设计要求、空间要求、配套设施要求、消防要求和质量要求。

Specifications for interior decoration design

DB32/T 3968-2021 模块装配式剪力墙结构应用技术规程

Technical specification for the application of modular assembly shear wall structures

T/CECS 779-2020 建筑物移位纠倾增层与改造技术标准

主要技术内容包括：总则、术语和符号、基本规定、检测及鉴定、移位工程、纠倾工程、增层工程、结构改造加固、地基基础加固、质量检测及验收等。

Technical standards for building displacement, inclination correction, story increase and renovation

T/SCDA 055-2020 630MPa级热处理带肋高强钢筋应用技术标准

1.本标准适用于配置天舜630MPa级热处理带肋高强钢筋的房屋和一般构筑物的钢筋混凝土结构设计、施工和质量验收。高强钢筋宜用作钢筋混凝土结构构件中纵向受力钢筋和预应力混凝土结构构件中非预应力受力钢筋；可用作抗剪、抗扭和抗冲切构件的横向钢筋；地基基础也可选用高强钢筋。高强钢筋不适用于轻骨料混凝土结构、特种混凝土结构和需作疲劳验算的混凝土构件；建筑上部结构及地下室中上部主体结构相关部位抗震等级为一、二、三级的框架和斜撑构件（含梯段）、剪力墙、核心筒不适用配置高强钢筋。  2.本标准中天舜630MPa级热处理带肋高强钢筋简称高强钢筋，钢筋技术条件须符合附录A“热处理带肋高强钢筋技术要求和检验方法”。符合本钢筋技术条件和检验方法规定的其他高强钢筋也适用本标准。

Application technical standard for 630MPa grade heat-treated ribbed high-strength steel bars

ASTM C1823/C1823M-20 粘结尺寸石料剪切粘结强度的标准试验方法

1.1 This test method is used for determining the shear bond strength of dimension stone wall or floor assembly adhered to a substrate. 1.2 This test method was developed for adhered stone applications and may be used in a laboratory or in the field. 1.3 Testing is performed on cured stone assemblies on a vertical or horizontal plane in an interior or exterior application. Load is applied to one edge of the stone. The load is applied at a specified rate until the stone assembly fails. 1.4 The values stated in either inch-pound units or SI units are to be regarded separately as standard. The values stated in each system are not necessarily exact equivalents; therefore, to ensure conformance with the standard, each system shall be used independently of the other, and values from the two systems shall not be combined. 1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Method for Shear Bond Strength of Adhered Dimension Stone

T/ZS 0129-2020 高大模板支撑工程智慧监测技术规程

目次 1  总  则　 2  术  语　 3  基本规定　 4  系统设计　 4.1  一般规定　 4.2  数据采集　 4.3  数据传输　 4.4  数据存储分析　 5  安装及调试　 5.1  一般规定　 5.2  安装　 5.3  调试　 6  验  收　 7  监测应用　 7.1  一般规定　 7.2  现场监测　 7.3  监测成果　 7.4  监测预警　 8  运行与维护 本规程用词说明　 引用标准名录　

Technical regulations for intelligent monitoring of tall formwork support engineering

T/ZS 0128-2020 既有建筑结构安全智慧监测技术规程

目次 1  总  则　 2  术  语　 3  基本规定　 4  系统设计　 4.1  一般规定　 4.2  传感器子系统　 4.3  数据采集与处理子系统　 4.4  数据传输子系统　 4.5  数据存储和管理子系统　 4.6  计算分析子系统　 4.7  安全预警子系统　 5  安装与调试　 5.1  一般规定　 5.2  安装　 5.3  调试　 6  验  收　 7  监测应用　 7.1  一般规定　 7.2  现场监测　 7.3  监测成果　 7.4  风险评估与监测预警　 8  运行与维护　 本规程用词说明　 引用标准名录　

Technical regulations for smart monitoring of existing building structures

T/ZS 0127-2020 既有建筑结构安全人工监测技术规程

目次 1  总  则　 2  术  语　 3  基本规定　 4  监测内容和方法　 4.1  一般规定　 4.2  监测项目　 4.3  巡视检查　 4.4  应急处置　 5  监测数据分析和预警　 6  监测成果　 本规程用词说明 引用标准名录　

Technical regulations for manual monitoring of existing building structures

DB64/T 1539-2020 复合保温板结构一体化系统应用技术规程

Composite thermal insulation board structural integration system application technical specification

ISO 13824:2020 结构设计基础.涉及结构的系统风险评估的一般原则

This document specifies general principles of risk assessment for s ys tems involving s tructures. The focus is on s trategic and operational decision-making related to design, assessment, maintenance and decommissioning of structures . This also includes formulation and calibration of related codes and standards . Systems involving structures can expose s takeholders at various levels in society to significant risks . The aim of this document is to facilitate and enhance decision-making with regard to monitoring, reducing and managing risks, and preparing for emergency in an efficient, cost-effective and transparent manner. Within the broader context of risk management, risk assessment provides decision-makers with procedures to determine whether or not, and in what manner, it is appropriate to treat risks. This document provides a general framework as well as a procedure for identifying hazards and estimating, evaluating and treating risks of s tructures and s ys tems involving s tructures. This document also provides a basis for code writers as well as designers to set reasonable target-reliability levels, such as s tated in ISO 2394, based on the result of risk considerations. For exis ting s tructures, it is intended that assessment of the risks associated with the events that were not considered in the original design or with changes in use be implemented according to the principles s tated in this document. This document can also be used for risk assessment of exceptional structures upon specific adaptation and detailing, the design of which is not usually within the scope of existing codes .

Bases for design of structures — General principles on risk assessment of systems involving structures

ISO 10252:2020 结构设计的基础 - 意外行动

Accidental actions can be subdivided into accidental actions with a natural cause and accidental actions due to human activities. This document applies to reliability based and risk informed decision making for the design and assessment of structures subject to accidental actions due to human activities. However, fires and human-made earthquakes are not included. The information presented in this document is intended for buildings and civil engineering works, regardless of the nature of their application and the use or combination of materials. The application of this document can require additional elements or elaboration in special cases. This document is intended to serve as a basis for those committees that are responsible for the task of preparing International Standards, national standards or codes of practice in accordance with given objectives and context in a particular country. Where relevant, it can also be applied directly to specific cases. This document describes how the principles of risk and reliability can be utilized to support decisions related to the design and assessment of structures subject to accidental actions and systems involving structures during all the phases of their service life. For the general principles of risk informed design and assessment, it is intended that ISO 2394 be considered. The application of this document necessitates knowledge beyond that which it contains. It is the responsibility of the user to ensure that this knowledge is available and applied.

Bases for design of structures — Accidental actions

DB11/T 1689-2019 文物建筑抗震鉴定技术规范

Technical code for seismic appraisal of cultural relic buildings

T/CSUS 06-2019 既有居住建筑外加装配式电梯工程技术标准

1.0.1 为规范和指导既有居住建筑外加装配式电梯工程，保证工程质量，做到安全可靠、技术先进、经济合理、绿色环保，制定本标准。 1.0.2 本标准适用于既有居住建筑外加装配式钢结构电梯的设计、施工、验收和运行维护。其他多层民用建筑外加装配式电梯可参考使用。 1.0.3既有居住建筑外加装配式电梯工程执行本标准外，应符合国家现行有关标准的规定。

Technical Standard for Additional Prefabricated Elevator Engineering of Existing Residential Building

ISO 22111:2019 结构设计基础 - 一般要求

This document provides the requirements for structural design and procedures following a semi- probabilistic approach that conform to the general principles for structural reliability as stipulated by for which sufficient knowledge and experience are commonly available on design and construction practice to ensure that target levels of reliability account for the nature and consequences of structural failure. Situations outside these limitations are covered by ISO 2394. The methods that are included in this document are the semi-probabilistic limit states approaches that are proven to achieve sufficient and consistent levels of structural reliability. This document relies on standardized procedures for the characterization of the load bearing performance of the structures within its scope. Sufficient information is needed on uncertainties of design variables and models to be able to derive semi-probabilistic design measures for verification of structural reliability within the scope of this and the related design standards.

Bases for design of structures — General requirements

19/30375290 DC BS ISO 13824 结构设计基础 涉及结构的系统风险评估的一般原则

BS ISO 13824. Bases for design of structures. General principles on risk assessment of systems involving structures

DB11/T 1607-2018 建筑物通信基站基础设施设计规范

Code for design of building communication base station infrastructure