91.080.30 砖石结构 标准查询与下载

ASTM C1531-22 砌体砂浆接缝抗剪强度指数现场测量的标准试验方法

1.1 These test methods cover procedures for the determination of the average in situ mortar joint shear strength index in existing unreinforced solid-unit and ungrouted hollow-unit masonry built with clay or concrete units. Three methods are provided: 1.1.1 Method A (with Flatjacks Controlling Normal Compressive Stress)—For determining mortar joint shear strength index when the state of normal compressive stress at the test site is controlled during the test using the flatjack method described in Test Method C1197. Horizontal displacement of the test unit is monitored throughout the test. The test setup for Method A is shown in Fig. 1. NOTE 1—A paper2 by Francesco Graziotti et. al of Univ. of Pavia included in ASTM STP 1612 discusses alternative methods for interpreting Method A testing results. 1.1.2 Method B (without Flatjacks Controlling Normal Compressive Stress)—For determining mortar joint shear strength index when using an estimate of the normal compressive stress at the location of the test site. Horizontal displacement of the test unit is not monitored during this procedure. The test set up for Method B is shown in Fig. 2. 1.1.3 Method C (with Flatjack Applying Horizontal Load)— For determining mortar joint shear strength index using an estimate of the normal compressive stress at the location of the test site, as shown in Fig. 3. Horizontal displacement of the test unit is generally not measured during this procedure. 1.2 The text of this standard refers to notes and footnotes that provide explanatory material. These notes and footnotes (excluding those in tables and figures) shall not be considered as requirements of the standard. 1.3 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Methods for In Situ Measurement of Masonry Mortar Joint Shear Strength Index

ASTM A951/A951M-22 砌体接缝钢筋用钢丝标准规范

1.1 This specification covers stainless steel and galvanized carbon steel masonry joint reinforcement fabricated from cold-drawn steel wire. Joint reinforcement consists of longitudinal wires welded to cross wires. 1.2 The values stated in either inch-pound units or SI units are to be regarded separately as standard. Within the text, the SI units are shown in brackets. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the specification. 1.3 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Steel Wire for Masonry Joint Reinforcement

ASTM C1715/C1715M-22 砖墙排水系统漏水性能评估的标准试验方法

1.1 This test method describes a standard procedure for determining the ability of masonry wall drainage systems to collect water that penetrates the exterior masonry wythe during rainstorms and to direct this water back to the exterior surface of the wall. 1.2 This test method is applicable to wall systems that contain an exterior masonry wythe with a drainage zone on the interior face of the exterior wythe. It is not applicable to single-wythe drainage walls. 1.3 This test method is not applicable to masonry barrier walls or other masonry walls that are designed without drainage zones behind the exterior wythe. 1.4 This test method covers the application of the testing using either inch-pound or SI units. The values stated in either SI units or inch-pound units are to be regarded separately as standard. Within the text, the inch-pound units are shown in brackets. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in nonconformance with the standard. 1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Method for Evaluation of Water Leakage Performance of Masonry Wall Drainage Systems

ASTM C1601-22a 砌体墙面渗水性现场测定的标准试验方法

1.1 This test method covers the field determination of water penetration of a masonry wall surface under specific water flow rate and air pressure conditions. This test is intended for use on any masonry wall surface that can be properly instrumented and tested within the requirements of this standard. This test method is not identical to and the results are not the same as laboratory standard Test Method E514/E514M. Test Method E514/E514M measures through-wall water penetration, whereas this test method only measures surface water penetration. 1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Method for Field Determination of Water Penetration of Masonry Wall Surfaces

T/SA 50-2022 新型树脂型人造石生产设备技术规范

1 术语和定义 2 工作条件 3 技术要求 4 试验方法 5 标签、包装、运输、贮存

Technical specification for new resin type artificial stone production equipment

GSO ASTM C1364:2022 建筑铸石标准规范

This specification establishes the physical requirements, sampling, testing, and visual inspection of architectural cast stone that may be made from facing and backup mixtures or from a homogeneous mixture, produced either by wet or dry casting. Conformances for raw materials, Portland cement, aggregates, coloring pigment, reinforcement, chemical admixtures, air entraining admixtures, water reducing and accelerating admixtures, ground slag, fly ash or natural pozzolan, and other consituents shall be precisely observed. Products shall also conform to specified physical and performance requirements such as compressive strength, cold water absorption, boiling water absorption, air content, field testing, resistance to freezing and thawing, and linear drying shrinkage.

Standard Specification for Architectural Cast Stone

T/SA 45-2022 人造大理石自动固化设备技术规范

1 术语和定义 2 工作条件 3 技术要求 4 试验方法 5 标志、包装、运输与贮存

Technical specification for automatic curing equipment of artificial marble

ASTM C1601-22 砌体墙面渗水性现场测定的标准试验方法

Standard Test Method for Field Determination of Water Penetration of Masonry Wall Surfaces

ASTM D5095-91(2022) 测定砖石防水处理用硅烷、硅氧烷和硅烷-硅氧烷混合物中不挥发物含量的标准试验方法

1.1 This test method describes a procedure for the determination of the nonvolatile content (Ns) of silanes, siloxanes, and blended silane-siloxane materials used in masonry water repellent treatments and is applicable to both solventand waterborne materials. 1.2 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. For a specific hazard statement, see Section 7. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Method for Determination of the Nonvolatile Content in Silanes, Siloxanes and Silane-Siloxane Blends Used in Masonry Water Repellent Treatments

ASTM D6904-03(2022) 砖石结构上应用的外部涂层抗风致雨的标准实施规程

1.1 This practice is for the evaluation of the ability of coatings to resist the passage of water through masonry block when exposed to water spray and air pressure. 1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Practice for Resistance to Wind-Driven Rain for Exterior Coatings Applied on Masonry

ASTM C1354/C1354M-22 石材中单个石材锚固强度的标准试验方法

1.1 This test method provides procedures for determining the ultimate strength of an assembly consisting of stone with mechanical anchor (anchorage). Load is applied, separately, perpendicular to the surface of the panel and parallel to the surface of the panel. This test is intended to represent the interaction of the anchor with the stone panel. However, influence of the backup structure on the strength of the assemblies is not included. 1.2 This test method is applicable to stone panels supported by mechanical anchors. 1.3 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Method for Strength of Individual Stone Anchorages in Dimension Stone

ASTM C1715/C1715M-21 砖墙排水系统漏水性能评定的标准试验方法

Standard Test Method for Evaluation of Water Leakage Performance of Masonry Wall Drainage Systems

ASTM E2260-21a 历史砌体重涂（勾缝）的标准指南

1.1 This guide applies only to existing historic masonry construction. For purposes of this guide historic masonry is intended to refer to buildings that have significant historic, architectural, cultural or social meaning and are constructed of masonry materials. Similar techniques and evaluation should be employed for non-historic masonry, but are not addressed in this guide. 1.2 This guide outlines procedures for repointing historic masonry and is intended to provide guidelines for the user to establish project-specific requirements for repointing of historic masonry. 1.3 This guide only pertains to masonry units: brick, terra cotta, stone, cast stone, and concrete brick laid in mortar, and may or may not be appropriate for other masonry units. 1.4 This guide addresses repointing (tuckpointing) as defined in 3.1.3. 1.5 When considering repointing, especially on masonry of artistic, architectural, cultural, or historical significance, guidance from a specialist experienced in historic masonry and repointing should be sought. 1.6 This guide does not address pointing styles or profiles used on masonry or the methods of producing them. 1.7 Additional repairs that may impact the structural integrity of the masonry may necessitate that a structural stability analysis be completed prior to the execution of any work. 1.8 Following this guide may involve hazardous materials, operations, and equipment. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory requirements prior to use. 1.9 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Guide for Repointing (Tuckpointing) Historic Masonry

ASTM C1354/C1354M-21 石材尺寸中单个石材锚固强度的标准试验方法

Standard Test Method for Strength of Individual Stone Anchorages in Dimension Stone

DB11/T 1832.4-2021 建筑工程施工工艺规程 第4部分：砌体结构工程

Construction technology specification for building engineering Part 4: Masonry structure engineering

DB52/T 1545-2020 堆石混凝土拱坝技术规范

Technical specifications for rock-fill concrete arch dams

ASTM C1601-20 砌体墙体表面水渗透场测定的标准试验方法

Standard Test Method for Field Determination of Water Penetration of Masonry Wall Surfaces

ASTM C1892/C1892M-20a 砌体中锚强度的标准试验方法

Standard Test Methods for Strength of Anchors in Masonry

ASTM E514/E514M-20 通过砖石渗透和渗漏的标准试验方法

1.1 This laboratory test method2 provides a procedure for determining the resistance to water penetration and leakage through unit masonry subjected to wind-driven rain. This test method is not identical to and the results are not the same as field standard Test Method C1601. This test method measures through-wall water penetration, whereas Test Method C1601 only measures surface water penetration. 1.2 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. For a specific hazard statement, see Section 6. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Method for Water Penetration and Leakage Through Masonry

DIN 20000-402/A1:2020 建筑产品在结构中的应用. 第402部分: 符合DIN EN 771-2-2015-11 的硅酸钙块体应用规则; 修改件1

This document contains amendments to DIN 20000-402: 2017-01 \

Application of building products in structures - Part 402: Rules for the application of calcium silicate masonry units according to DIN EN 771-2:2015-11; Amendment 1