91.100.50 (Binders. Sealing materials) 标准查询与下载

ASTM D226-06 房顶和防水用沥青饱和有机毡的标准规范

1.1 This specification covers asphalt-saturated organic felts, with or without perforations, intended to be used with asphalts conforming to the requirements of Specification D 312 in the construction of built-up roofs, and with asphalts conforming to the requirements of Specification D 449 in the construction of water proofing systems.1.2 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only.The following safety hazards caveat pertains only to the test method portion, Section , of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Specification for Asphalt-Saturated Organic Felt Used in Roofing and Waterproofing

ASTM C1083-06 弹性泡沫垫圈和密封材料吸水性的标准试验方法

This test method will quantify the water absorption characteristics of cellular elastomeric gaskets and sealing materials. It is a test that enables the specifier to exercise engineering judgment in the selection of materials.1.1 This test method covers those cellular elastomeric compounds that are manufactured in preformed shapes such as gaskets, and that are used as compression seals for glazing purposes and as sealing materials in other applications in building construction.This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.1.2 The values stated in SI units are to be regarded as the standard. The values given in parentheses are provided for information purposes only.

Standard Test Method for Water Absorption of Cellular Elastomeric Gaskets and Sealing Materials

ASTM D2824/D2824M-06(2012)e1 无纤维增强、石棉纤维增强和无石棉的纤维增强的填充铝颜料的沥青屋面涂层标准规格

1.1 This specification covers asphalt-based, aluminum roof coatings suitable for application to roofing or masonry surfaces by brush or spray. 1.2 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard. 1.3 The following precautionary caveat pertains only to the test method portion, Section 8, of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Specification for Aluminum-Pigmented Asphalt Roof Coatings, Nonfibered, Asbestos Fibered, and Fibered without Asbestos

ASTM C1442-06 用人工老化仪对密封件进行试验的标准实施规范

1.1 This practice covers three types of laboratory weathering exposure procedures for evaluating the effect of actinic radiation, heat, and moisture on sealants.1.2 The exposure sources used in the three types of artificial weathering devices are the filtered xenon arc, fluorescent ultraviolet lamps, and open flame carbon arc based on Practices G 155, G 154, and G 152, respectively.1.3 The values stated in SI units are to be regarded as the standard. The values given in parentheses are provided for information only.1.4 The ISO standard related to this Practice is ISO 11431. Significant differences exist between the procedures. The ISO specimens are exposed through glass and are elongated prior to examination for loss of adhesion or cohesion, or both, following exposure.1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Practice for Conducting Tests on Sealants Using Artificial Weathering Apparatus

ASTM D5643/D5643M-06(2012)e1 不含石棉的煤焦油屋顶水泥标准规格

1.1 This specification covers coal tar roof cement suitable for trowel application in coal tar roofing and flashing systems. 1.2 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Specification for Coal Tar Roof Cement, Asbestos Free

ASTM C732-06(2012) 人工风蚀对胶乳密封料老化效果的标准试验方法

Accelerated weathering exposure serves to indicate long-term exterior durability of the sealant. In this test method, durability is tested when the sealant is used with wood or aluminum.1.1 This test method covers a laboratory procedure for the determination of aging effects of artificial weathering on latex sealants. 1.2 The values stated in metric (SI) units are to be regarded as the standard. The values given in parentheses are for information only. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. Note 18212;Currently there is no ISO standard similar to this test method.

Standard Test Method for Aging Effects of Artificial Weathering on Latex Sealants

ASTM C910-06(2011) 单一成份弹性溶剂释放型密封胶的粘结力及粘聚力的标准试验方法

1.1 This test method determines the bond and cohesion of one-part, elastomeric, solvent release-type sealants after high- and low-temperature aging. 1.2 The subcommittee with jurisdiction is not aware of any similar ISO standard. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. Note 18212;Currently there is no ISO standard similar to this test method.

Standard Test Method for Bond and Cohesion of One-Part Elastomeric Solvent Release-Type Sealants

ASTM C961-06(2011) 密封材料的搭接剪切强度的标准试验方法

Sealants are generally subjected to longitudinal and lateral shear stresses in end use applications. This test method measures the cohesive strength of sealants when subjected to shear stresses, and also provides information regarding the adhesive bond to the substrates being tested.1.1 This test method covers a laboratory procedure for determining the lap shear strength of sealants. It also provides information on the adhesive bond of the sealants to the tested substrates. 1.2 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. 1.4 The subcommittee with jurisdiction of this standard is not aware of any similar or equivalent ISO standard.

Standard Test Method for Lap Shear Strength of Sealants

ASTM C716-06 安装锁条衬垫和填补上光材料的标准规范

1.1 This specification covers installation procedures for lock-strip gaskets that comply with Specification C 542 and for infill glazing materials in lockstrip gasket glazing applications used in building walls which are not more than 15 from a vertical plane. The prime performance considerations are weathertightness against air and water infiltration, and structural integrity under wind loads.1.2 The values stated in inch-pound units are to be regarded as the standard. The SI units in parentheses are provided for information only.1.3 The committee with jurisdiction over this standard is not aware of any comparable standards published by other organizations.

Standard Specification for Installing Lock-Strip Gaskets and Infill Glazing Materials

ASTM C836-06 与独立磨损层一起使用的高固体含量并使用冷却液体的弹性防水薄膜的标准规范

1.1 This specification describes the required properties and test methods for a cold liquid-applied elastomeric-type membrane, one or two component, for waterproofing building decks and walls subject to hydrostatic pressure in building areas to be occupied by personnel, vehicles, or equipment. This specification applies only to a membrane system that will be covered with a separate wearing course, traffic course, or backfill. Note 18212;See Guide C 898 and Guide C 1471 for proper application of membrane.1.2 There are no ISO standards similar or equivalent to this ASTM standard.1.3 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only.This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Specification for High Solids Content, Cold Liquid-Applied Elastomeric Waterproofing Membrane for Use with Separate Wearing Course

ASTM C961-06 密封材料的搭接剪切强度的标准试验方法

Sealants are generally subjected to longitudinal and lateral shear stresses in end use applications. This test method measures the cohesive strength of sealants when subjected to shear stresses, and also provides information regarding the adhesive bond to the substrates being tested.1.1 This test method covers a laboratory procedure for determining the lap shear strength of sealants. It also provides information on the adhesive bond of the sealants to the tested substrates.1.2 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only.This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.1.3 The subcommittee with jurisdiction of this standard is not aware of any similar or equivalent ISO standard.

Standard Test Method for Lap Shear Strength of Sealants

ASTM C1083-06(2011) 蜂窝状弹性垫圈和密封材料的吸水性的标准试验方法

This test method will quantify the water absorption characteristics of cellular elastomeric gaskets and sealing materials. It is a test that enables the specifier to exercise engineering judgment in the selection of materials.1.1 This test method covers those cellular elastomeric compounds that are manufactured in preformed shapes such as gaskets, and that are used as compression seals for glazing purposes and as sealing materials in other applications in building construction. 1.2 The values stated in SI units are to be regarded as the standard. The values given in parentheses are provided for information purposes only. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Test Method for Water Absorption of Cellular Elastomeric Gaskets and Sealing Materials

ASTM D5147-06 改良沥青薄板材抽样和试验用标准试验方法

1.1 These test methods cover procedures for sampling and testing prefabricated, reinforced, polymer-modified bituminous sheet materials designed for single- or multiple-ply application in roofing and waterproofing membranes. These products may use various surfacing materials on one side.1.2 These test methods appear in the following order:1.3 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only.This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Test Methods for Sampling and Testing Modified Bituminous Sheet Material

ASTM C1248-06 用接缝密封胶着色多孔衬底的标准试验方法

Staining of building materials is an aesthetically undesirable occurrence. This test method evaluates the likelihood of a sealant causing an early stain on a porous substrate due to exudation of materials from the sealant. Since this is an accelerated test, it does not necessarily predict that the tested sealants will not stain or discolor porous substrates over longer periods of time.1.1 This test method covers four types of laboratory tests to determine if a joint sealant has a probability of staining a porous substrate (such as marble, limestone, sandstone, and granite). The tests are on compressed samples and include (1) storage under standard laboratory conditions, (2) storage in an oven, and (3) exposure in a fluorescent UV/condensation device, and (4) exposure in a xenon arc device.1.2 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only.This standard does not purport to address all of the safety problems, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.1.3 The committee with jurisdiction over this standard is not aware of any comparable standards published by other organizations.

Standard Test Method for Staining of Porous Substrate by Joint Sealants

ASTM C734-06 胶乳密封料受人工气候影响后的低温柔韧性的标准试验方法

This test evaluates the flexibility of artificially weathered latex sealants in a low-temperature environment.1.1 This test method covers a laboratory procedure for the determination of low-temperature flexibility of latex sealants after 500 h artificial weathering.1.2 The values stated in metric (SI) units are to be regarded as the standard. The values given in parentheses are for information only.This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.Note 1Currently there is no ISO standard similar to this test method.

Standard Test Method for Low-Temperature Flexibility of Latex Sealants After Artificial Weathering

ASTM C716-06(2011) 安装锁条衬垫和填补上光材料的标准规范

This specification can be referred to in contract documents as a method and workmanship standard for the installation of lock-strip gasket glazing systems. See also related standards (Specifications C542 and C963, Guide C964, and Terminology C717).1.1 This specification covers installation procedures for lock-strip gaskets that comply with Specification C542 and for infill glazing materials in lockstrip gasket glazing applications used in building walls which are not more than 15° from a vertical plane. The prime performance considerations are weathertightness against air and water infiltration, and structural integrity under wind loads. 1.2 The values stated in inch-pound units are to be regarded as the standard. The SI units in parentheses are provided for information only. 1.3 The committee with jurisdiction over this standard is not aware of any comparable standards published by other organizations.

Standard Specification for Installing Lock-Strip Gaskets and Infill Glazing Materials

ASTM C981-05 房屋盖板用组合沥青薄膜防水装置设计的标准指南

This guide provides information and guidelines for the selection of components and the design of a built-up bituminous membrane waterproofing system in building deck construction. Where the state of the art is such that criteria for particular conditions are not established or have numerous variables that require consideration, applicable portions of Design Considerations, Sections 5-16, serve as reference and guidance for selection by the designer of the system.1.1 This guide describes the design of fully adhered built-up bituminous membrane waterproofing systems for plaza deck and promenade construction over occupied spaces of buildings where covered by a separate wearing course.1.2 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only.1.3 The committee with jurisdiction over this standard is not aware of any comparable standards published by other organizations.1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Guide for Design of Built-Up Bituminous Membrane Waterproofing Systems for Building Decks

ASTM C510-05a 单一或多组分接缝密封料的着色和颜色变化的标准试验方法

Staining of a building is an aesthetically undesireable occurance. This test method evaluates the likelihood of a sealant causing early stain on a porous substrate due to certain chemical exudations from the sealant. 4.1.1 This test method may not predict staining caused by such factors as residue run-down or dirt pick-up by a sealant exudate. This test method is useful to predict potential color changes in the sealant itself after weathering. This test method measures color change in a sealant and staining of substrate by the sealant under conditions of artificial weathering. See also Test Method D 2203, which measures staining by a sealant due to gross exudations from the sealant; it does not subject the sealant to artificial weathering.1.1 This test method covers an accelerated laboratory procedure to determine if a sample of a joint sealant will stain the substrate when in contract with masonry, concrete, or stone (such as marble, limestone, sandstone, and granite). This test method also is intended to determine whether the sealant itself will change in color when exposed to the weather.1.2 The values stated in SI units are to be regarded as the standard. The value given in parentheses are for information only.1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Test Method for Staining and Color Change of Single- or Multicomponent Joint Sealants

ASTM C1184-05 结构硅密封件的标准规范

1.1 This specification describes the properties of cold liquid applied, single-component or multicomponent, chemically curing elastomeric structural silicone sealants herein referred to as the sealant. These sealants are intended to structurally adhere components of structural sealant glazing systems.1.2 Only those properties for which there are industry-agreed-upon minimum acceptable requirements, as determined by available ASTM test methods, are described in this specification. Additional properties may be added as ASTM test methods for those properties become available.1.3 The values stated in metric (SI) units are to be regarded as the standard. The values in parentheses are for information only.1.4 Committee C24, with jurisdiction over this specification, is aware of two comparable standards by other organizations: ETAG No. 002 and the Chinese national standard GB16776.

Standard Specification for Structural Silicone Sealants

ASTM C510-05 单一或多组分接缝密封料的着色和颜色变化的标准试验方法

1.1 This test method describes an accelerated laboratory procedure to determine if a sample of a joint sealant will stain the substrate when in contract with masonry, concrete, or stone (such as marble, limestone, sandstone, and granite). This test method also is intended to determine whether the sealant itself will change in color when exposed to the weather. 1.2 The values stated in SI units are to be regarded as the standard. The value given in parentheses are for information only. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Test Method for Staining and Color Change of Single- or Multicomponent Joint Sealants