91.140.80 排水系统 标准查询与下载

DB34/T 2978.1-2017 装配式化粪池技术要求 第1部分：三格式

DB34/T 2978 的本部分规定了装配式三格化粪池的术语和定义、基本要求、规格型号、要求、试验 方法、检验规则、标志、运输和储存。 本部分适用于村镇旱厕改造用装配式三格化粪池（以下简称化粪池），污水改造等其他用途亦可以 参照使用

Technical requirements for prefabricated septic tanks Part 1: Three formats

DB34/T 2978.2-2017 装配式化粪池技术要求 第2部分：双瓮式

DB34/T 2978 的本部分规定了装配式双瓮化粪池的术语和定义、基本要求、规格型号、要求、试验 方法、检验规则、标志、运输和储存。 本部分适用于村镇旱厕改造用装配式双瓮化粪池（以下简称化粪池），污水改造等其他用途亦可以 参照使用

Technical requirements for prefabricated septic tanks Part 2: Double urn type

DIN EN 1253-5:2017 建筑物用集水沟.第5部分:可截流轻液体的集水沟;德文版本EN 1253-5-2017

Gullies for buildings - Part 5: Gullies with light liquids closure; German version EN 1253-5:2017

DB31/T 1043-2017 暴雨强度公式与设计雨型标准

本标准规定了上海市暴雨强度公式与设计雨型标准的适用范围、术语和定义、符号和单位、暴雨强度公式、暴雨设计雨型。 本标准适用于上海市市域范围的室外排水系统规划、设计与评估。

Rainstorm Intensity Formula and Design Rain Pattern Standard

T/CECS 463-2017 污水提升装置应用技术规程

总则、术语、污水提升装置、设计、施工安装、验收、维护保养

Technical specification for application of sewage-elevating device

BS EN 1253-5:2017 建筑物的沟壑 轻质液体封闭的沟渠

Gullies for buildings. Gullies with light liquids closure

EN 1253-5:2017 建筑物排水装置.第5部分:封闭的轻流体排水装置要求和试验方法

This European Standard specifies requirements for the design, construction, performance, application and marking as well as test methods of factory made gullies with a light liquid closure for buildings. Light liquid closures for buildings are applied to avoid uncontrolled discharge of light liquids into drainage systems in case of emergency. This European Standard does not apply to installations for separation of light liquids covered by EN 858-1.

Gullies for buildings - Part 5: Gullies with light liquids closure

ASTM F2764/F2764M-17 无压卫生下水道应用6至60英寸[150至1500 mm]聚丙烯(PP)波纹状双壁和三壁管及配件的标准规格

1.1 This specification covers requirements and test methods for corrugated double and triple wall polypropylene pipe and fittings. The nominal inside diameters covered are 6 to 60 in. [150 to 1500 mm]. 1.2 The requirements of this specification are intended to provide pipe and fittings for underground use for non-pressure sanitary sewer systems. Pipe and fittings produced in accordance with this specification shall be installed in compliance with Practice D2321. 1.3 This specification covers pipe and fittings with an annular corrugated wall and an essentially smooth interior wall (that is, double wall) (Fig. 1) and pipe and fittings with an annular corrugated wall and an essentially smooth interior and exterior wall (that is, triple wall) (Fig. 2). FIG. 1 Typical Corrugated Double Wall Pipe FIG. 2 Typical Corrugated Triple Wall Pipe 1.4 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard. 1.5 The following precautionary statement applies only to Section 7 of this specification. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. 1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for 6 to 60 in. [150 to 1500 mm] Polypropylene (PP) Corrugated Double and Triple Wall Pipe and Fittings for Non-Pressure Sanitary Sewer Applications

ASTM F2764/F2764M-17e1 无压卫生下水道应用6至60英寸[150至1500 mm]聚丙烯(PP)波纹状双壁和三壁管及配件的标准规格

1.1 This specification covers requirements and test methods for corrugated double and triple wall polypropylene pipe and fittings. The nominal inside diameters covered are 6 to 60 in. [150 to 1500 mm]. 1.2 The requirements of this specification are intended to provide pipe and fittings for underground use for non-pressure sanitary sewer systems. Pipe and fittings produced in accordance with this specification shall be installed in compliance with Practice D2321. 1.3 This specification covers pipe and fittings with an annular corrugated wall and an essentially smooth interior wall (that is, double wall) (Fig. 1) and pipe and fittings with an annular corrugated wall and an essentially smooth interior and exterior wall (that is, triple wall) (Fig. 2). FIG. 1 Typical Corrugated Double Wall Pipe FIG. 2 Typical Corrugated Triple Wall Pipe 1.4 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard. 1.5 The following precautionary statement applies only to Section 7 of this specification. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. 1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for 6 to 60 in. [150 to 1500 mm] Polypropylene (PP) Corrugated Double and Triple Wall Pipe and Fittings for Non-Pressure Sanitary Sewer Applications

DIN EN 1253-3:2016 建筑物集水沟.第3部分:质量控制.德文版本EN 1253-3-2016

Gullies for buildings - Part 3: Evaluation of conformity; German version EN 1253-3:2016

CJ/T 233-2016 建筑小区排水用塑料检查井

本标准规定了建筑小区排水用塑料检查井的构造、分类及标记、材料、要求、试验方法、检验规则、标志、包装、运输和贮存。 本标准适用于建筑小区(居住区、公共建筑区、厂区等)内，井内底埋深不大于6 m，埋地管径不大于800 mm的排水用塑料检查井。

Plastic inspection chamber for sewerage in building area

DIN EN 1253-4:2016 建筑物的雨水进口.第4部分:入口封盖物.德文版本EN 1253-4-2016

Gullies for buildings - Part 4: Access covers; German version EN 1253-4:2016

CJ/T 489-2016 塑料化粪池

本标准规定了塑料化粪池(以下简称“化粪池”)的分类与标记、原材料、要求、试验方法、检验规则、标志、运输和贮存。 本标准适用于化粪池池顶覆土不大于2 m，以聚乙烯(PE)、聚丙烯(PP)或硬聚氯乙烯(PVC-U)为主要原材料制作成型的化粪池。

Thermo plastic septic tank

BS EN 1253-3:2016 建筑物集水沟.符合性评定

Gullies for buildings. Evaluation of conformity

BS EN 1253-4:2016 建筑物的沟壑 检修盖

Gullies for buildings. Access covers

EN 1253-3:2016 建筑物的沟槽-第3部分:合格评定

This European Standard specifies the requirements for evaluation of conformity for floor gullies, roof drains and access covers for buildings to ensure conformity of these products with EN 1253-1, EN 1253-2 and EN 1253-4.

Gullies for buildings - Part 3: Evaluation of conformity

EN 1253-4:2016 建筑物排水装置.第4部分:通路盖

This European Standard classifies access covers according to their loading strength and specifies requirements relating to their design, construction, marking, testing and evaluation of conformity. This European Standard classifies and specifies requirements for factory made access covers used for drainage systems inside buildings. This European Standard does not apply to access covers intended for external use which are covered by EN 124 series.

Gullies for buildings - Part 4: Access covers

ASTM B789/B789M-16 为涵洞和下水道安装波纹率结构板管的标准实施规程

4.1 Corrugated aluminum structural plate pipe functions structurally as a flexible ring that is supported by and interacts with the compacted surrounding soil. The soil placed around the structure is thus an integral part of the structural system. It is therefore important to ensure that the soil structure is made up of the acceptable material and well-constructed. Field verification of soil structure acceptability using Test Methods D1556, D2167, D6938, or D2937, as applicable, and comparing the results with Test Methods D698 or D1557, in accordance with the specifications for each project, is the most reliable basis for installation of an acceptable structure. The required density and method of measurement are not specified by this practice but must be established in the specifications for each project. 1.1 This practice covers procedures, soils, and soil placement for the proper installation of corrugated aluminum structural plate culverts and sewers in either trench or embankment installations. A typical trench installation is shown in Fig. 1, and a typical embankment (projection) installation is shown in Fig. 2. Structural plate structures as described herein are those structures factory fabricated in plate form and bolted together on site to provide the required shape, size, and length of structure. This practice applies to structures designed in accordance with Practice B790/B790M. 1.2 The values stated in either inch-pound units or SI units are to be regarded separately as standard. Within the text, the SI units are shown in brackets. The values stated in each system are not exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in nonconformance with the standard. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Practice for Installing Corrugated Aluminum Structural Plate Pipe for Culverts and Sewers

DB35/T 1537-2015 可调式防沉降球墨铸铁检查井盖

本标准规定了可调式防沉降球墨铸铁检查井盖的术语和定义、分类和结构形式、材料、要求、试验方法、检验规则、标志、包装、运输和贮存。 本标准适用于安装在绿化带、人行道、非机动车道、机动车行道、停车场、广场等地面的可调式防沉降球墨铸铁检查井盖、可调式防沉降球墨铸铁雨水篦子、可调式防沉降球墨铸铁装饰检查井盖。

Adjustable anti-settling ductile iron inspection manhole cover

CJ/T 295-2015 餐饮废水隔油器

本标准规定了餐饮废水隔油器的术语和定义、产品标记、结构型式和参数、使用环境、要求、试验方法、检验规则、标志、包装、运输和贮存。 本标准适用于处理水量：不大于55 m/h；废水动(植)物油油脂含量不大于500 mg/L，悬浮物浓度不大于600 mg/L；水温不低于5 ℃的餐饮废水的隔油器设计、制造和检验。

Grease-water separator for restaurant wastewater