91.200 施工技术 标准查询与下载

GOST 34081-2017 建筑物和建筑. 自然振荡基本音调参数的确定

Buildings and constructions. Determination of parameters of the basic tone of natural oscillations

DIN 18216:2017 模板结. 要求、测试、使用

This Standard specifies formwork ties used for single- or double-sided formwork. Formwork ties bear the loads which act on the formwork until it is removed.

Formwork ties; requirements, testing, use

DB11/T 1384-2016 室内钢索支吊架施工规程

Indoor steel cable support and hanger construction regulations

DB11/T 1363-2016 塑料排（蓄）水板施工技术规程

Construction technical specification for plastic row (storage) water board

T/SDAS 5-2016 QY钢丝网架（片）一体化板现浇混凝土 复合保温系统应用技术规程

为规范QY钢丝网架（片）一体化板现浇混凝土复合保温系统的设计、施工及验收，做到技术先进、经济合理、安全适用和保证工程质量，制定本规程。

QY steel wire grid (sheet) integrated slab cast-in-place concrete composite thermal insulation system application technical specification

DB11/T 1343-2016 建筑内外墙涂料施工及验收规程

Specifications for construction and acceptance of building interior and exterior wall coatings

DB11/T 696-2016 预拌砂浆应用技术规程

Technical specification for the application of ready-mixed mortar

DB11/T 1342-2016 玻璃纤维增强筋支护技术规程

Technical specification for glass fiber reinforced rib support

DB37/T 5053-2016 装配式结构独立钢支柱临时支撑系统应用技术规程

本规程适用于装配式结构预制混凝土梁、板的施工中采用独立钢支柱临时支撑系统的设计、施工、使用及管理。

Technical specification for application of temporary support system for independent steel pillars of prefabricated structures

DB11/T 1314-2015 混凝土外加剂应用技术规程

Technical specification for the application of concrete admixtures

DB11/T 1313-2015 薄抹灰外墙外保温用聚合物水泥砂浆应用技术规程

Technical specification for the application of polymer cement mortar for external thermal insulation of thin plastered exterior walls

GSO ISO 7077:2015 建筑测量方法 检查尺寸符合性的一般原则和程序

  Scope is not provided for this standard

Measuring methods for building -- General principles and procedures for the verification of dimensional compliance

GSO ISO 7727:2015 建筑连接 连接建筑构件的原则 解决施工过程中的尺寸变化

  Scope is not provided for this standard

Joints in building -- Principles for jointing of building components -- Accommodation of dimensional deviations during construction

BS 5930:2015 现场调查实施规程

Code of practice for ground investigations

SH/T 3557-2015 石油化工大型设备运输施工规范

本规范规定了石油化工大型设备运输的技术要求。 本规范适用于石油化工工程项目中，满足下列条件之一的设备运输： --设备质量大于等于100t； --设备长度大于等于20m； --设备宽度大于等于4. 5m； --设备高度大于等于3. 8m。

Construction specification for large equipment transporting in petrochemical industry

DB42/T 1035-2015 热轧U型钢板桩技术规程

Technical specifications for hot-rolled U-shaped steel sheet piles

ASTM D4756-15 刚性聚氯乙烯侧 (PVC) 板和底板安装的标准实践规程

1.1 This practice covers the basic requirements for and the methods of installation of rigid vinyl siding, soffits, and accessories on the exterior wall and soffit areas of buildings. In all applications, refer also to the specific manufacturer's installation instructions and the requirements of applicable building codes. 1.2 This practice covers aspects of installation relating to effectiveness and durability in service. 1.3 The various application systems are located in the following sections of this practice: Substrate, Surface Preparation Section 8 Application of Horizontal Siding Section 9 Application of Vertical Siding Section 10 Application of Soffits and Fascia Section 11 Special Details Section 12 1.4 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. Note 1: There is no known ISO equivalent to this standard.

Standard Practice for Installation of Rigid Poly(Vinyl Chloride) (PVC) Siding and Soffit

GSO ISO 3443-1:2014 建筑物的公差 第1部分：评估和规范的主要原则

This International Standard describes the nature of dimensional variability in building and the purposes for which it has to be quantified, and defines the factors to be taken into account in the evaluation, specification and verification of tolerances for the manufacture of building components and for site work. It applies to components and buildings generally, including those designed in accordance with the principles of modular co-ordination.

Tolerances for building -- Part 1: Basic principles for evaluation and specification

GSO ISO 4463-3:2014 建筑测量方法 标记和测量 第3部分：履行测量和测量服务的清单

This part of ISO 4463 identifies and provides guidance in the form of check-lists for the surveying and setting-out services that may be required during the development and construction of buildings and ancillary works. It will assist those involved in specifying the surveying and setting-out services required during the procurement of buildings by providing a check-list of the requirements from which selections can be made and to which further items can be added depending on the particular needs of the project. The guidance is applicable to both new construction and refurbishment projects.

Measurement methods for building -- Setting-out and measurement -- Part 3: Check-lists for the procurement of surveys and measurement services

GSO ISO 4463-2:2014 建筑测量方法 标记和测量 第2部分：测量目标和测站

This part of ISO 4463 deals with the progressive stages of establishing and marking measuring stations and targets on building sites. The aspects covered are planning, functional needs and maintenance. This part of ISO 4463 applies to measuring stations and targets in all types of building construction. Examples of different stations and targets and location plans are given in annex A.

Measurement methods for building -- Setting-out and measurement -- Part 2: Measuring stations and targets