93.040 桥梁建筑 标准查询与下载

DB50/T 960-2019 双壁钢围堰设计及施工技术规范

Technical specification for design and construction of double-wall steel cofferdam

T/ZS 0076-2019 装配式冷弯薄壁型钢房屋施工质量验收标准

目 次 1? 总则 2? 术语和符号 2.1? 术语 2.2? 符号 3? 基本规定 4? 材料及构配件 4.1? 一般规定 4.2? 钢材及其制成品 4.3? 结构面板 4.4? 连接件 4.5? 紧固件 5? 结构工程 5.1? 一般规定 5.2? 地基与基础 5.3? 主体结构 5.4? 构件连接与紧固 6? 设备与管线工程 6.1? 一般规定 6.2? 给水管线 6.3? 排水管线 6.4? 电气系统 6.5? 空调和新风系统 6.6? 安防系统 6.7? 智能控制系统? 7? 外围护工程 7.1? 一般规定? 7.2? 外围护节能  7.3? 外围护防水 7.4? 外饰面 7.5? 外门窗 8? 内装工程? 8.1? 一般规定 8.2? 楼（地）面  8.3? 吊顶 8.4? 墙面 8.5? 室内门窗 8.6? 装配式卫生间 8.7? 装配式厨房 附录?A? 质量验收记录 本标准用词说明 引用标准名录

Construction quality acceptance criteria for prefabricated cold-formed thin-walled steel houses

DB36/T 1197-2019 桥梁预应力孔道压浆密实度检测规程

Regulations for testing the density of grouting in bridge prestressed tunnels

DB34/T 3464-2019 城市桥梁限载标准

本标准适用于安徽省城市规划区、县城规划区内除工矿特色型城镇以外的既有、新建或改扩建并通行汽车车辆的城市桥梁的限载。

Urban bridge load limit standard

DB34/T 3465-2019 连续梁桥整体同步顶升技术规程

本规程适用于市政连续梁桥顶升工程，其他结构形式的桥梁顶升可参照使用。

Technical specification for overall synchronous jacking of continuous girder bridges

T/CECS G:D66-01-2019 公路波纹钢涵洞技术规程

总则、术语和符号、基本规定、材料、 结构设计、构造规定、地基与基础、耐久性设计、施工、质量检验、附录 A 常用波纹钢 涵洞规格表、附录 B 设计流程图、附录 C 纵向螺栓接缝承载力试验。

Technical Specification of Highway Corrugated Steel Culvert

T/CECS G-D66-01-2019 公路波纹钢涵洞技术规程

Technical specification for highway corrugated steel culverts

T/CECS G-M61-01-2019 公路混凝土桥梁拆除技术规程

Highway Concrete Bridge Demolition Technical Regulations

T/CECS G:M61-01-2019 公路混凝土桥梁拆除技术规程

总则、术语和符号、基本规定、 拆除设计、拆除施工、桥面铺装及附属构造拆除、上部结构拆除、下部结构拆除、 拆除施工监控、拆除安全、环境保护，附录 A 爆破拆除。

Technical Specifications for Road Concrete Bridge Demolition

T/HQPA 2-2019 榫型钢阻尼减震支座

本标准技术内容规定了原材料的质量要求，产品的性能指标，试验方法及检验规则。

Tenon type steel damping isolation bearing

T/HQPA 3-2019 补充硅脂型耐久球型支座

本标准技术内容规定了原材料的质量要求，产品的性能指标，试验方法及检验规则。

Supplementary silica resistant spherical steel bearing

DB61/T 1290-2019 高速公路隧道消防现场管理秩序规范

Regulations on management order of fire scene in expressway tunnel

DB61/T 1288-2019 桥梁结构预应力检测技术规程

Technical specification for bridge structure prestress testing

DB61/T 1289-2019 公路隧道地质雷达检测技术规程

Technical regulations for geological radar detection of highway tunnels

DB34/T 3445-2019 全体外预应力节段拼装混凝土桥梁设计与施工指南

Guidelines for design and construction of overall externally prestressed segmental assembled concrete bridges

ASTM D3542-08(2019) 桥梁预成型聚氯丁二烯弹性接头密封标准规范

1.1 This specification covers the material requirements for preformed polychloroprene elastomeric joint seals for bridges. The seal consists of a multiple-web design composed of polychloroprene and functions only by compression of the seal between the faces of the joint with the seal folding inward at the top to facilitate compression. The seal is installed with a lubricant adhesive and is designed to seal the joint and reject incompressibles. NOTE 1—This specification may not be applicable for seals whose height is less than 90 % of its nominal width. 1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Preformed Polychloroprene Elastomeric Joint Seals for Bridges

T/TMAC 016-2019 环境隔离式橡胶支座

       本标准规定了环境隔离式橡胶支座的产品分类、代号、产品结构，技术要求，试验方法，检验规则，标志、包装、运输、贮存和支座安装的要求。        本标准适用于公路、铁路、市政工程桥梁用竖向承载力不大于5000 kN的橡胶支座，其他工程可参照使用。

Environmentally isolated rubber mounts

T/TMAC 017-2019 桥梁三级设防摩擦摆减隔震支座

       本标准规定了桥梁三级设防摩擦摆减隔震支座的产品术语和定义，分类、结构形式、规格及型号，技术要求，试验方法，检验规则、标志、包装、运输和储存的要求。        本标准适用于竖向承载力为1 000 kN～60 000 kN的公路桥梁三级设防摩擦摆减隔震支座。

Friction pendulum shock-absorbing and isolation bearings for three-level fortification of bridges

T/CHTS 20007-2019 《公路桥梁缆索用锌-铝合金镀层钢丝》

本标准按照《中国公路学会标准编写规则》(T/CHTS10001)编写,共分8章和2个附录,主要内容包括:范围,规范性引用文件,术语和符号,分类、型号与规格,技术要求,试验方法,检验规则,包装、标志、运输和储存。

Zinc-Aluminum Alloy Coated Steel Wire for Highway Bridge Cables

T/CHTS 10017-2019 《港珠澳大桥施工技术指南 第六分册 钢混组合箱梁制造及安装》

本指南按照《中国公路学会标准编写规则》（T/CHTS 10001）编制，共分为10章，主要内容包括总则、术语和符号、施工准备、材料及试验、桥面板预制、开口钢箱梁制造、组合梁组合、组合梁运输及安装、组合梁体系转换及组合梁施工监控。

Manufacture and Installation of Steel-concrete Composite Box Girder in the Sixth Volume of the Construction Technical Guide for the Hong Kong-Zhuhai-Macao Bridge