93.080.10 道路建筑 标准查询与下载

GSO EN 500-1:2011 移动式道路施工机械 安全 第1部分：一般要求

1.1 This part of EN 500 specifies the common safety requirements for mobile road construction machinery ). The EN 500 series is applicable to mobile road construction machinery as listed in Annex A. When no specific standard exists, EN 500-1 applies. It specifies common requirements for the design and construction of mobile road construction machinery in order to protect workers from accidents and health hazards which could occur during operation, loading, transport and maintenance. Additional specific requirements for certain types of mobile road construction machinery are given in parts 2 to 4 and 6 of this standard. This part of this standard gives safety requirements for all types of mobile road construction machinery and shall be used in conjunction with one of the parts 2 to 4 and 6. These machine-specific parts do not repeat the requirements from part 1 but add to or replace the requirements for the type of mobile road construction machinery in question. Machine-specific requirements in parts 2 to 4 and 6 take precedence over the respective requirements of this stan-dard. For types of mobile road construction machinery not dealt with in parts 2 to 4 and 6, EN 500-1 applies and if for those machinery additional derived risks may arise, these risks have to be taken into consideration. 1.2 This European Standard deals with all significant hazards, hazardous situations and events relevant to mobile road construction machinery, when they are used as intended and under conditions of misuse which are reasonably foreseeable (see Clause 4). This European Standard specifies the appropriate technical measures to eliminate or reduce risks arising from the significant hazards as specified in Clause 4. 1.3 This European Standard applies to machines which are manufactured after the date of publication of this European Standard by CEN.

Mobile road construction machinery - Safety - Part 1: Common requirements

GSO EN 13020:2011 路面处理设备 安全要求

This document applies to road surface treatment machines, which are in particular: - binder sprayers [or sprayers]; - chipping spreaders [or spreaders]; - machines for surface repairs (binder sprayer chipping spreader [or sprayer spreader]); - mastics asphalt mixers; - joint sealer; - micro-surfacing machines/slurry machines; - cold asphalt laying / micro-asphalt-paving machines; (see also Clause 3). Road surface treatment machines can be mounted on a carrier vehicle, trailer or articulated truck, combining to form an integral unit. It is also possible to mount a road surface treatment machine on its own chassis construction and propulsion system (self-propelled or pedestrian-controlled). In all cases the machine and chassis form an integral unit. Directives and standards for the vehicular truck chassis aspects, termed 'carrier vehicle' in this document, would be those relative to that equipment, even where specific modifications have been made to realize the road surface treatment application. The use in public road traffic is governed by the national regulations. This document deals with all significant hazards identified through a risk assessment relevant to road surface treatment machines when they are used as intended and under the conditions foreseen by the manufacturer (see Clause 4). This document does not deal with significant hazards associated with pressurized tanks, noise and EMC. This document specifies the appropriate technical measures to eliminate or reduce risks arising from the significant hazards associated with machine operation, setting and adjustments, load discharge and routine maintenance. This document does not include requirements for the carrier vehicles or special constructions. These are covered in directives related to the construction of vehicles. Demountable bodywork systems (e.g. demountable containers) are specified in other standards.

Road surface treatment machines - Safety requirements

GSO EN 500-3:2011 移动式道路施工机械 安全 第3部分：土壤固化机和回收机的特殊要求

This part of EN 500 specifies the safety requirements for soil-stabilising machines and recycling machines as de-fined in Clause 3 and deals with all significant hazards, hazardous situations and events relevant to these ma-chines, when they are used as intended and under conditions of misuse which are reasonably foreseeable. This part of EN 500 contains additional requirements to EN 500-1 "Common requirements".

Mobile road construction machinery - Safety - Part 3: Specific requirements for soil-stabilising machines and recycling machines

GSO EN 500-6:2011 移动式道路施工机械 安全 第6部分：路面整修设备的特殊要求

This part of EN 500 specifies the safety requirements for paver-finishers as defined in Clause 3 and deals with the significant hazards relevant to these machines, when they are used as intended and under conditions of misuse which are reasonably foreseeable. This part of EN 500 contains additional requirements to EN 500-1 "Common requirements". If internal and/or external vibrators are used for concrete paving, then prEN 12649 applies.

Mobile road construction machinery - Safety - Part 6: Specific requirements for paver-finishers

GSO EN 500-2:2011 移动式道路施工机械 安全 第2部分：道路刮土机的特殊要求

This part of EN 500 specifies the safety requirements for road-milling machines as defined in Clause 3 and deals with all significant hazards, hazardous situations and events relevant to these machines, when they are used as intended and under conditions of misuse which are reasonably foreseeable. This part of EN 500 contains additional requirements to EN 500-1 "Common requirements".

Mobile road construction machinery - Safety - Part 2: Specific requirements for road-milling machines

DIN EN 500-4:2011 移动式筑路机械.安全性.第4部分-夯实机械的特定要求;德文版本EN 500-4-2011

This part of EN 500 specifies the safety requirements for compaction machines as defined in Clause 3 and deals with all significant hazards, hazardous situations and events relevant to compaction machines, when they are used as intended and under conditions of misuse which are reasonably foreseeable. This document specifies additional requirements to and/or exceptions from EN 500-1 "Common requirements". This part of EN 500 is not applicable for seated ride-on operated rollers with a drum width less than nominal 0,8 m.

Mobile road construction machinery - Safety - Part 4: Specific requirements for compaction machines; German version EN 500-4:2011

LST EN 500-4-2011 移动式筑路机械 安全 第4部分：压实机的特殊要求

Mobile road construction machinery - Safety - Part 4: Specific requirements for compaction machines

BS EN 500-4:2011 移动式筑路机械.安全性.夯实机械的具体要求

This part of EN 500 specifies the safety requirements for compaction machines as defined in Clause 3 and deals with all significant hazards, hazardous situations and events relevant to compaction machines, when they are used as intended and under conditions of misuse which are reasonably foreseeable. This document specifies additional requirements to and/or exceptions from EN 500-1 ”Common requirements”. This part of EN 500 is not applicable for seated ride-on operated rollers with a drum width less than nominal 0,8 m.

Mobile road construction machinery. Safety. Specific requirements for compaction machines

DS/EN 500-4:2011 移动式筑路机械 安全 第4部分：压实机的特殊要求

This part of EN 500 specifies the safety requirements for compaction machines as defined in Clause 3 and deals with all significant hazards, hazardous situations and events relevant to compaction machines, when they are used as intended and under conditions of misuse which are reasonably foreseeable.This document specifies additional requirements to and/or exceptions from EN 500-1 """"Common requirements"""".

Mobile road construction machinery - Safety - Part 4: Specific requirements for compaction machines

EN 500-4:2011 移动式筑路机械.安全性.夯实机械的具体要求

This part of EN 500 specifies the safety requirements for compaction machines as defined in Clause 3 and deals with all significant hazards, hazardous situations and events relevant to compaction machines, when they are used as intended and under conditions of misuse which are reasonably foreseeable.This document specifies additional requirements to and/or exceptions from EN 500-1 "Common requirements".This part of EN 500 is not applicable for seated ride-on operated rollers with a drum width less than nominal 0,8 m.

Mobile road construction machinery - Safety - Part 4: Specific requirements for compaction machines

ASTM E1890-11 对新领域基准滑动阻力测量系统和设备进行验证的标准试验方法

Friction characteristics of traveled surfaces are monitored by skid measurement systems, and the operating procedure for the use of these systems is Test Method E274. However, dynamic measurement differences between these systems, that comply with the requirements of Test Method E274, require that each of these systems be correlated to each other system. The most effective approach to accomplish this correlation is to compare each system to a singular, highly accurate system, or to a very limited number (two or three) of systems, in a controlled environment. The ARSMS''s were designed to be such systems. Fig. 1 depicts a skid measurement system and shows the general location of the major components. This guide defines the process of ensuring that the ARSMS''s continue to accomplish their intended purpose.1.1 This guide covers validating area reference skid measurement systems (ARSMS) and related equipment. These systems have been used since 1976 to evaluate and correlate Test Method E274 skid measurement systems used primarily as a pavement management tool by state Departments of Transportation. Also, this guide provides guidelines for the revalidation process following the replacement of components within an ARSMS. 1.2 This guide is offered as a process to identify and quantify the variables that affect system performance, to minimize the effect of these variables, and to provide a method of validating a new ARSMS to replace an existing ARSMS that has provided quality correlation data for a very long time. 1.3 The values stated in inch-pound units are to be regarded as the standard since the ARSMS will be compared with state departments of transportation systems that all currently use inch-pound units. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Guide for Validating New Area Reference Skid Measurement Systems and Equipment

ASTM E1890-11(2015) 用于验证新的区域参考滑动测量系统和设备的标准指南

5.1 Friction characteristics of traveled surfaces are monitored by skid measurement systems, and the operating procedure for the use of these systems is Test Method E274. However, dynamic measurement differences between these systems, that comply with the requirements of Test Method E274, require that each of these systems be correlated to each other system. The most effective approach to accomplish this correlation is to compare each system to a singular, highly accurate system, or to a very limited number (two or three) of systems, in a controlled environment. The ARSMS's were designed to be such systems. Fig. 1 depicts a skid measurement system and shows the general location of the major components. 5.2 This guide defines the process of ensuring that the ARSMS's continue to accomplish their intended purpose. 1.1 This guide covers validating area reference skid measurement systems (ARSMS) and related equipment. These systems have been used since 1976 to evaluate and correlate Test Method E274 skid measurement systems used primarily as a pavement management tool by state Departments of Transportation. Also, this guide provides guidelines for the revalidation process following the replacement of components within an ARSMS. 1.2 This guide is offered as a process to identify and quantify the variables that affect system performance, to minimize the effect of these variables, and to provide a method of validating a new ARSMS to replace an existing ARSMS that has provided quality correlation data for a very long time. 1.3 The values stated in inch-pound units are to be regarded as the standard since the ARSMS will be compared with state departments of transportation systems that all currently use inch-pound units. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Guide for Validating New Area Reference Skid Measurement Systems and Equipment

SNI 2416-2011 如何使用 Benkelman Beam 工具测试弯曲路面挠度

Cara uji lendutan perkerasan lentur dengan alat Benkelman Beam

DB21/T 1848-2010 稀浆封层设计与施工技术指南

Design and Construction Technical Guidelines for Slurry Seals

DB21/T 1847-2010 沥青路面厂拌热再生技术指南

Asphalt Pavement Plant Mix Hot Recycling Technical Guide

DIN EN 13020:2010 路面处理机械.安全性要求.德文版本EN 13020-2004+A1-2010

This document applies to road surface treatment machines, which are in particular:binder sprayers [or sprayers];chipping spreaders[or spreaders]

Road surface treatment machines - Safety requirements; German version EN 13020:2004+A1:2010

LST EN 13020-2004+A1-2010 路面处理机 安全要求

Road surface treatment machines - Safety requirements

DS/EN 13020+A1:2010 路面处理机 安全要求

This document applies to road surface treatment machines, which are in particular:- binder sprayers [or sprayers];- chipping spreaders [or spreaders];- machines for surface repairs (binder sprayer chipping spreader [or sprayer spreader]);- mastics asphalt mixers;- joint sealer;- micro-surfacing machines/slurry machines;- cold asphalt laying / micro-asphalt-paving machines;(see also Clause 3).Road surface treatment machines can be mounted on a carrier vehicle, trailer or articulated truck, combining to form an integral unit. It is also possible to mount a road surface treatment machine on its own chassis construction and propulsion system (self-propelled or

Road surface treatment machines - Safety requirements

NF E58-171:2010 路面处理机械.安全性要求

Road surface treatment machines - Safety requirements.

JIS A 8510:2010 路面清理机械用安全性要求

Safety requirements for road surface cleaning machines