97.100.20 气体加热器 标准查询与下载

CSA/ANSI Z21.56:19 • CSA 4.7-2019 燃气泳池加热器

1 Scope 1.1 This Standard applies to newly produced pool heaters (see Clause 3, Definitions), hereinafter referred to as pool heaters or appliances, constructed entirely of new, unused parts and materials, for heating non- potable water stored at atmospheric pressure, such as water in swimming pools, spas, hot tubs and similar applications: a) for use with natural gas; b) for use with manufactured gas; c) for use with mixed gas; d) for use with liquefied petroleum gases; e) for use with LP gas-air mixtures; f) for installation in applications intended to temper the entire flow of the primary circulating pool loop water prior to re-entering the pool; and g) for installation in applications for pool heaters intended to temper a portion of the primary circulating loop water diverted through the pool heater by mechanical means, and then re-enter and mix with the primary circulating loop water prior to entering the pool. 1.2 This Standard applies to pool heaters intended for installation at a distance less than 5 ft (1.52 m) from the inside surface of a pool or spa, hereinafter referred to as close proximity heaters (see Clause 3). 1.3 This Standard applies to pool heaters for indoor installation with draft hoods which are factory equipped with automatic vent damper devices (see Clause 3, Definitions), hereinafter referred to as vent damper devices. 1.4 This Standard applies to pool heaters of other than the direct vent type which are factory equipped with electrically operated or mechanically actuated automatic flue damper devices (see Clause 3, Definitions), hereinafter referred to as flue damper devices. 1.5 If a value for measurement as given in this Standard is followed by an equivalent value in other units, the first stated value is to be regarded as the specification. 1.6 All references to psi throughout this Standard are to be considered gauge pressure unless otherwise specified. 1.7 Clause 7contains clauses that are unique to the United States. 1.8 Clause 8contains clauses that are unique to Canada. 1.9 Special construction clauses applicable to a water heater designed for use with an optional listed conversion kit are outlined under Annex D. 1.10 Clause 2, Reference publications, contains a list of standards specifically referenced in this Standard, and sources from which these reference standards may be obtained. 1.11 In this Standard, “shall” is used to express a requirement, i.e., a provision that the user is obliged to satisfy in order to comply with the standard; “should” is used to express a recommendation or that which is advised but not required; and “may” is used to express an option or that which is permissible within the limits of the Standard. Notes accompanying clauses do not include requirements or alternative requirements; the purpose of a note accompanying a clause is to separate from the text explanatory or informative material. Notes to tables and figures are considered part of the table or figure and may be written as requirements. Annexes are designated normative (mandatory) or informative (non-mandatory) to define their application.

Gas-fired pool heaters

BS EN 416:2019 非家用燃气架空辐射管加热器和辐射管加热器系统 安全和能源效率

What is BS EN 416 - Gas-fired overhead radiant tube heaters about?    BS EN 416 discusses gas-fired overhead radiant tube heaters and radiant tube heater systems.   BS EN 416 specifies the requirements and test methods for the construction, safety, classification, marking, and efficiency of non-domestic gas-fired overhead radiant tube heaters incorporating a single burner and multiple burner systems (referred to in the body of the text as the “system”) with each burner unit under the control of an automatic burner control system.    For radiant tube heaters incorporating a single burner, BS EN 416 is applicable to Type A2, A3,   B12, B13, B22, B23, B42, B43, B52, B53, C12, C13, C32, C33, C52 and C53 appliances intended for use in other than domestic dwellings, in which the supply of combustion air and/or the evacuation of the products of combustion is achieved by mechanical means located upstream of the draught diverter if provided.  

Gas-fired overhead radiant tube heaters and radiant tube heater systems for non-domestic use. Safety and energy efficiency

BS EN 17082:2019 用于空间供暖的家用和非家用燃气强制对流空气加热器 净热输入不超过 300 kW

What is BS EN 17082 - Gas-fired air heaters about?    BS EN 17082 discusses domestic and non-domestic gas-fired forced convection air heaters for space heating. BS EN 17082 specifies the requirements and test methods for the safety and efficiency of gas-fired air heaters with or without a fan to assist the transportation of combustion air and/or flue gases, hereafter referred to as "appliances". BS EN 17082 also applies to warm air heaters having forced draught burners.   BS EN 17082 applies to Type A2, A3 appliances, with an input not exceeding 300 kW (net CV   basis), intended for non-domestic use.

Domestic and non-domestic gas-fired forced convection air heaters for space heating not exceeding a net heat input of 300 kW

BS EN 419:2019 非家用燃气高架发光辐射加热器 安全和能源效率

What is BS EN 419 - Gas-fired overhead luminous radiant heaters about?    BS EN 419 discusses gas-fired overhead luminous radiant heaters. BS EN 419 specifies the requirements and test methods for the construction, safety, rational use of energy, classification, and marking of non-domestic gas-fired overhead luminous radiant heaters for environmental comfort, referred to in the body of the text as “appliances.   BS EN 419 is applicable to Type A1 and Type A3 appliances only intended for use other than residential dwellings:   Low gas pressure appliances operating at pressures up to and including 50 mbar   Medium gas pressure appliances operating at pressures above 50 mbar and up to 2 bar   Note:

Gas-fired overhead luminous radiant heaters for non-domestic use. Safety and energy efficiency

T/CAS 360-2019 带增压预热功能家用燃气快速热水器

本标准规定了带增压、预热或同时具有该两种功能的家用燃气快速热水器的术语和定义、要求、试验方法、检验规则及标志、安装、包装、运输和贮存。 本标准适用于热负荷不大于70 kW、带增压预热功能的家用燃气快速热水器（以下简称“热水器”）。

Household gas instant water heater with supercharging and preheating function

JIS S 2122:2019 家用燃气空间加热器

Gas burning space heaters for domestic use

BS 5864:2019 额定热输入净值不超过 70kW 的燃气管道式空气加热器的安装和维护（第二和第三系列燃气） 规格

What is this standard about? This British Standard covers how engineers should choose, install and maintain certain types of gas-fired warm air heater, specifically in accordance with the EU’s Energy Related Products Directive. Who is this standard for? Related training centres Installers Service engineers Manufacturers Notified bodies Test houses Department of Communities and Local Government – Building Regulations Organizations which carry out work on behalf of government in support of Building Regulations and the Standard Assessment Procedure Trade bodies – e.g. The Institute of Gas Engineers and Managers Gas Safe Register End-users interested in their warm air heaters and installation Why should you use this standard? This is the only recognized industry standard for the installation and maintenance of gas-fired warm air units. Its purpose is to help engineers safely install warm air heaters, particularly in accordance with the new EU Energy Related Products Directive. The standard specifies requirements for the selection, installation and maintenance (see Note 1) of flued, gas-fired, ducted-air heaters of rated heat input not exceeding 70 kW, based on net calorific value, burning 2nd or 3rd family gases to heat one or more rooms or internal spaces in either domestic premises (see Note 2) or commercial premises. It applies to warm air heaters that incorporate a fan to circulate the warm air, to combined air heater/circulator installations and to the servicing and maintenance of heaters that distribute warm air by natural convection. The standard doesn’t apply to gas installations in towed or motorized leisure accommodation vehicles.   NOTE 1: For the purposes of this standard, installation includes design, insp...

Installation and maintenance of gas-fired ducted air heaters of rated heat input not exceeding 70 kW net (2nd and 3rd family gases). Specification

T/CECS 10007-2018 燃气采暖热水炉及热水器用燃烧器

本标准规定了燃气采暖热水炉（以下简称采暖炉）及家用燃气快速热水器（以下简称热水器）用燃烧器的术语和定义，分类，材料、结构和外观，性能要求，试验方法，检验规则，标志和使用说明书，包装、运输和贮存。

Burner for combiboiler and water heater

KS B 8052-2018 燃气发动机驱动的热泵空调器 - 非管道燃气发动机驱动的热泵空调condtioners试验和额定性能

Gas heat pumps — Non-ducted appliances for heating and cooling — Testing and rating for performance

JIS S 2153:2017 带液化石油气筒的燃气取暖器

Portable gas space heaters with LPG cartridge

BS EN 14543:2017 专用液化石油气器具规范 - 遮阳伞露台加热器 - 室外或通风良好区域使用的无烟道辐射加热器

Specification for dedicated liquefied petroleum gas appliances - Parasol patio heaters - Flueless radiant heaters for outdoor or amply ventilated area use

EN 14543:2017 专用液化石油气设备用规范.伞式庭院加热器.户外或较大通风区域用无管辐射加热器

Specification for dedicated liquefied petroleum gas appliances - Parasol patio heaters - Flueless radiant heaters for outdoor or amply ventilated area use

T/ZRCX 03-2016 《商用燃气灶具能效等级和能效限定值》

主要技术内容： 1、规范术语、定义    商用燃气灶具能效限定值，商用燃气灶具节能评价值，燃气矮仔炉（矮汤炉），燃气煲仔炉（平头炉）的规范。 2、能效等级分类    商用燃气灶具能效等级按表1规定分为3级，其中1级能效最高。 3、试验方法及检验规则    实验条件，实验用燃气，试验方法等； 4、能效等级标注

《Energy efficiency grades evaluating for commercial gas appliances》

KS B 8053-2015(2020) 燃气机热泵空调器管道燃气机热泵空调器性能试验与评定

Gas engine driven heat pump air conditioners－ducted gas engine driven heat pump air conditioners－Testing and rating for performance

KS B 8053-2015 燃气热泵 管道式冷热设备 额定性能和运行性能试验

Gas engine driven heat pump air conditioners－ducted gas engine driven heat pump air conditioners－Testing and rating for performance

JIS B 8627:2015 燃气发动机驱动的热泵空调器

Gas engine driven heat pump air conditioners

DIN EN 13278:2014 前开式独置燃气加热器.德文版本EN 13278-2013

Open fronted gas-fired independent space heaters; German version EN 13278:2013

GOST 33010-2014 多个房间内置燃气加热装置. 要求和试验方法

Gas-fired insets for heating more than one room. Requirements and test methods

BS EN 13278:2013 前面敞开的燃气独立房间取暖器

Open fronted gas-fired independent space heaters

GOST 32451-2013 前开式独置燃气空间加热器

Open fronted gas-fired independend space heaters