97.100.20 气体加热器 标准查询与下载

BS 6896:2011 工业和商业加热用燃气式架空辐射加热器的安装和维护规范(2类和3类家用燃气)

This British Standard specifies the installation requirements for gas-fired overhead radiant heaters and systems for the environmental heating of premises other than domestic dwellings. This standard only applies to appliances falling within the scope of the Gas Appliances (Safety) Regulations 1995 [1]. It is applicable to the installation of heaters that are designed to use gases of group H of the 2nd family (e.g. natural gas), gases of group P of the 3rd family (e.g. propane) as well as gases of group B of the 3rd family (e.g. butane) (see BS EN 437+A1). NOTE 1 This standard does not specifically cover LPG/air for which additional requirements might be necessary. It is applicable to the installation of gas-fired overhead luminous radiant heaters conforming to BS EN 419-1, single burner gas-fired overhead radiant heaters conforming to BS EN 416-1 and multi-burner gas-fired overhead radiant tube heater systems conforming to BS EN 777-1, BS EN 777-2, BS EN 777-3 and BS EN 777-4. NOTE 2 For the purposes of this standard, installation includes design, inspection and commissioning. It is recognized that each of these tasks may, at times, be performed by the same persons. NOTE 3 The heat inputs and ventilation rates in cm2/kW of heat input given in this standard are based on the net calorific value. It is not applicable to the installation of gas-fired overhead radiant heaters and systems: a) to which the Gas Appliances (Safety) Regulations 1995 [1] do not apply; b) that are designed for use in domestic premises; c) that are supplied with a heated fluid from a separate source; or d) that are portable or transportable.

Specification for installation and maintenance of gas-fired overhead radiant heaters for industrial and commercial heating (2nd and 3rd family gases)

GOST R 54819-2011 不连接烟囱的家用液化石油气加热器

Domestic heaters dedicated for liquefied petroleum gases, not connected to a chimney

ANSI Z83.20-2008, Z 83.20a-2010, Z 83.20b-2011 燃气管和低强度红外加热器标准(同CSA 2.34标准)

Standard for Gas-Fired Tubular and Low Intensity Infrared Heaters (same as CSA 2.34)

JIS S 2122:2010 家用燃气空间加热器

Gas burning space heaters for domestic use

BS 5864:2010 额定输入净值不超过70 kW的燃气管道式空气加热器的安装和维修(2类和3类燃气).规范

This Part of BS 5502 gives recommendations for the design, construction and use of agricultural storage tanks and reception pits for livestock slurry. NOTE Further sources of information are given in Appendix A. The titles of the publications referred to in this standard are listed on page 24.

Installation and maintenance of gas-fired ducted air heaters of rated heat input not exceeding 70 kW net (2nd and 3rd family gases). Specification

DIN EN 1319:2010 有鼓风机辅助燃烧的净热输入不超过70 kW的家用燃气驱动空间供热用对流空气加热器.德文版本EN 1319-2009

Domestic gas-fired forced convection air heaters for space heating, with fan-assisted burners not exceeding a net heat input of 70 kW; German version EN 1319:2009

DIN EN 14829 Berichtigung 1:2010 家用燃气标定热负荷不超过6kW的无烟道单独采暖炉; 德文版本EN 14829: 2007, DIN EN 14829: 2007-11勘误表

Independent gas-fired flueless space heaters for nominal heat input not exceeding 6 kW; German version EN 14829:2007, Corrigendum to DIN EN 14829:2007-11

DIN EN 1020:2010 带有风扇助燃气体或燃烧产品传输、净热输入功率不超过300kW的空间加热用非家用强制对流空气加热器.德文版本 EN 1020-2009

This European Standard specifies the requirements and test methods for the safety and efficiency of non-domestic gas-fired air heaters having a fan to assist the transportation of combustion air and/or flue gases, hereafter referred to as "appliances". This includes appliances having forced draught burners.This European Standard applies to Type B12, B13, B14, B22, B23, B42, B43, B44, B52, B53, C12, C13, C32, C33, C62 and C63 appliances with a heat input not exceeding 300 kW (based on net calorific value) intended for use in other than single unit residential dwellings. It also applies to appliances intended for outdoor installation. Provision of the heated air may be by means of ducting or may be directly into the heated space. For Type C62 and C63 appliances, this European Standard only applies when such appliances are intended for final installation in a similar manner to Type C3 appliances.

Non-domestic forced convection gas-fired air heaters for space heating not exceeding a net heat input of 300 kW incorporating a fan to assist transportation of combustion air or combustion products; German version EN 1020:2009

DIN EN 621:2010 无风扇输送助燃气体和/或燃烧物质、净热输入功率不超过300kW的空间加热用非家用燃气式强制对流空气加热器

This European Standard specifies the requirements and test methods for the safety and efficiency of non-domestic gas-fired air heaters not exceeding a net heat input of 300 kW with (an) atmospheric burner(s) and without a fan to assist the transportation of combustion air and/or flue gases, hereafter referred to as "appliances". This European Standard applies to Type B, B, C and C, appliances intended for use in other than single unit residential dwellings. Provision of the heated air may be by means of ducting or may be directly into the heated space. This standard does not apply to: a) appliances intended for use in a single unit residential dwelling; b) appliances of the condensing type; c) appliances for outdoor installation; d) dual purpose air conditioning appliances (heating and cooling); e) appliances where the air is heated by an intermediate fluid; f) appliances with forced draught burners; g) appliances fitted with a manual or automatic means of adjusting the combustion air supply or the combustion products evacuation (including flue dampers); h) portable or transportable forced convection appliances; i) appliances having multiple heating units with a single draught diverter; j) appliances fitted with more than one flue outlet. k) appliances that are designed for continuous condensation within the flue system under normal operating conditions; l) appliances having combustion products evacuation ducts, POCEDs, that are non-metallic. This standard is applicable to appliances which are intended to be type tested. It also includes requirements concerning the evaluation of conformity, including factory production control, but these requirements only apply to POCEDs and their associated terminals.

Non-domestic gas-fired forced convection air heaters for space heating not exceeding a net heat input of 300 kW, without a fan to assist transportation of combustion air and/or combustion products; German version EN 621:2009

LST EN 1319-2010 用于空间加热的家用燃气强制对流空气加热器，带有风扇辅助燃烧器，净热输入不超过 70 kW

Domestic gas-fired forced convection air heaters for space heating, with fan-assisted burners not exceeding a net heat input of 70 kW

LST EN 1020-2010 用于空间加热的非家用强制对流燃气空气加热器，净热输入不超过 300 kW，装有风扇以协助输送燃烧空气或燃烧产物

Non-domestic forced convection gas-fired air heaters for space heating not exceeding a net heat input of 300 kW incorporating a fan to assist transportation of combustion air or combustion products

LST EN 621-2010 用于空间加热的非家用燃气强制对流空气加热器的净热输入不超过 300 千瓦，没有风扇来协助输送燃烧空气和/或燃烧产物

Non-domestic gas-fired forced convection air heaters for space heating not exceeding a net heat input of 300 kW, without a fan to assist transportation of combustion air and/or combustion products

DS/EN 1319:2010 用于空间加热的家用燃气强制对流空气加热器，带有风扇辅助燃烧器，净热输入不超过 70 kW

This European Standard specifies the requirements and test methods for the safety and efficiency of domestic gas-fired air heaters with a fan to assist the transportation of combustion air and/or combustion products, hereafter referred to as appliances.This European Standard applies to Type B12, B12AS, B12BS, B13, B13AS, B13BS, B14, B14AS, B14BS, B22, B23, B42, B42AS, B42BS, B43, B43AS, B43BS, B44, B44AS, B44BS, B52, B53, C12, C13, C32, C33, C62 and C63 appliances with an input not exceeding 70 kW (net cv basis), intended primarily for use in single unit residential dwellings. Provision of the heated air may be by means of ducting.This standard does not app

Domestic gas-fired forced convection air heaters for space heating, with fan-assisted burners not exceeding a net heat input of 70 kW

LST EN 778-2010 用于空间加热的家用燃气强制对流空气加热器净热输入不超过 70 千瓦，没有风扇来协助输送燃烧空气和/或燃烧产物

Domestic gas-fired forced convection air heaters for space heating not exceeding a net heat input of 70 kW, without a fan to assist transportation of combustion air and/or combustion products

NF E31-508:2010 带有净输入热量不超过70KW风扇辅助燃烧器的空间供暖用的家用燃气强制对流空气加热器

Domestic gas-fired forced convection air heaters for space heating, with fan-assisted burners not exceeding a net heat input of 70 kW.

BS EN 1020:2009 借助风扇传输燃气和/或燃烧产物的空间加热净加热输入功率不超过300 kW的非家用燃气强制对流空气加热器

This European Standard specifies the requirements and test methods for the safety and efficiency of nondomestic gas-fired air heaters having a fan to assist the transportation of combustion air and/or flue gases, hereafter referred to as "appliances". This includes appliances having forced draught burners. This European Standard applies to Type B12, B13, B14, B22, B23, B42, B43, B44, B52, B53, C12, C13, C32, C33, C62 and C63 appliances with a heat input not exceeding 300 kW (based on net calorific value) intended for use in other than single unit residential dwellings. It also applies to appliances intended for outdoor installation. Provision of the heated air may be by means of ducting or may be directly into the heated space. For Type C62 and C63 appliances, this European Standard only applies when such appliances are intended for final installation in a similar manner to Type C3 appliances. This standard does not apply to: a) appliances intended for use in a single unit residential dwelling; b) appliances of the condensing type; c) appliances with atmospheric burners without a fan to assist the transportation of combustion air and/or flue gases; d) dual purpose air conditioning appliances (heating and cooling); e) appliances where the air is heated by an intermediate fluid; f) appliances fitted with manual or automatic flue dampers; g) portable or transportable forced convection appliances; h) appliances having multiple heating units with a single draught diverter; i) appliances fitted with more than one flue outlet; j) appliances that are designed for continuous condensation within the flue system under normal operating conditions; k) appliances having combustion products evacuation ducts, POCEDs, that are non-metallic. This standard is applicable to appliances which are intended to be type tested. It also includes requirements concerning the evaluation of conformity, including factory production control, but these requirements only apply to POCEDs and their associated terminals. NOTE Requirements for appliances which are not type tested would need to be subject to further consideration.

Non-domestic forced convection gas-fired air heaters for space heating not exceeding a net heat input of 300 kW incorporating a fan to assist transportation of combustion air or combustion products

BS EN 1319:2009 净加热输入量不超过70kW的带有风扇辅助锅炉的家用空间加热燃气强制对流空气加热器

This European Standard specifies the requirements and test methods for the safety and efficiency of domestic gas-fired air heaters with a fan to assist the transportation of combustion air and/or combustion products, hereafter referred to as appliances. This European Standard applies to Type B12, B12AS, B12BS, B13, B13AS, B13BS, B14, B14AS, B14BS, B22, B23, B42, B42AS, B42BS, B43, B43AS, B43BS, B44, B44AS, B44BS, B52, B53, C12, C13, C32, C33, C62 and C63 appliances with an input not exceeding 70 kW (net cv basis), intended primarily for use in single unit residential dwellings. Provision of the heated air may be by means of ducting. This standard does not apply to: a) appliances of the condensing type; b) appliances for outdoor installation; c) dual purpose air conditioning appliances (heating and cooling); d) appliances where the air is heated by an intermediate fluid; e) appliances with forced draught package burners or fully premixed burners; f) appliances fitted with a manual means of adjusting the combustion air supply or the evacuation of the combustion products; g) portable or transportable forced convection appliances; h) appliances having multiple heating units with a single draught diverter; i) appliances fitted with more than one flue outlet; j) Type C22, C23, C42, C43, C52 and C53 appliances; k) appliances that are designed for continuous condensation within the flue system under normal operating conditions; l) appliances having combustion products evacuation ducts, POCEDs, that are non-metallic. This standard is applicable to appliances which are intended to be type tested. It also includes requirements concerning the evaluation of conformity, including factory production control, but these requirements only apply to POCEDs and their associated terminals.

Domestic gas-fired forced convection air heaters for space heating, with fan-assisted burners not exceeding a net heat input of 70 kW

BS EN 621:2009 不带风扇辅助助燃空气和/或燃烧产物传输的,净供热不超过300 kW的非空间加热用家用燃气强制对流热风机

This European Standard specifies the requirements and test methods for the safety and efficiency of nondomestic gas-fired air heaters not exceeding a net heat input of 300 kW with (an) atmospheric burner(s) and without a fan to assist the transportation of combustion air and/or flue gases, hereafter referred to as "appliances". This European Standard applies to Type B11, B41, C11 and C31 appliances intended for use in other than single unit residential dwellings. Provision of the heated air may be by means of ducting or may be directly into the heated space. This standard does not apply to: a) appliances intended for use in a single unit residential dwelling; b) appliances of the condensing type; c) appliances for outdoor installation; d) dual purpose air conditioning appliances (heating and cooling); e) appliances where the air is heated by an intermediate fluid; f) appliances with forced draught burners; g) appliances fitted with a manual or automatic means of adjusting the combustion air supply or the combustion products evacuation (including flue dampers); h) portable or transportable forced convection appliances; i) appliances having multiple heating units with a single draught diverter; j) appliances fitted with more than one flue outlet; k) appliances that are designed for continuous condensation within the flue system under normal operating conditions; l) appliances having combustion products evacuation ducts, POCEDs, that are non-metallic. This standard is applicable to appliances which are intended to be type tested. It also includes requirements concerning the evaluation of conformity, including factory production control, but these requirements only apply to POCEDs and their associated terminals. NOTE Requirements for appliances which are not type tested would need to be subject to further consideration.

Non-domestic gas-fired forced convection air heaters for space heating not exceeding a net heat input of 300 kW, without a fan to assist transportation of combustion air and/or combustion products

BS EN 1319:2010 装有净加热输入量不超过70kW风扇辅助锅炉的家用空间加热燃气强制对流空气加热器

Domestic gas-fired forced convection air heaters for space heating, with fan-assisted burners not exceeding a net heat input of 70 kW

BS EN 1020:2010 借助风扇传输燃气和/或燃烧产物的空间加热净加热输入功率不超过300KW的非家用燃气强制对流空气加热器

Non-domestic forced convection gas-fired air heaters for space heating not exceeding a net heat input of 300 kW incorporating a fan to assist transportation of combustion air or combustion products