97.100.40 液体燃料加热器 标准查询与下载

23/30471435 DC BS EN 1-1 住宅液体燃料燃烧器具第1部分：一般要求和试验方法

BS EN 1-1. Residential liquid fuel burning appliances - Part 1. General requirements and test methods

23/30471438 DC BS EN 1-2 住宅液体燃料燃烧器具 第 2 部分：带汽化燃烧器的烟道油炉

BS EN 1-2. Residential liquid fuel burning appliances - Part 2. Flued oil stoves with vaporizing burners

T/QGCML 428-2022 管线式饮水机生产技术规范

本文件规定了管线式饮水机的分类与命名、技术要求、检验方法、检验规则、包装、运输和贮存技术要求。 本文件适用于家庭、公共区域等类似用途的管线式饮水机相关技术规范，其他相似饮水机亦可参考使用。

Technical specifications for the production of pipeline water dispensers

T/CAREI 002-2022 民用甲醇采暖炉

本文件规定了民用甲醇采暖炉（以下简称采暖炉）的分类和编码、技术要求、试验方法、检验规则、标志、警示标识、说明书、包装、运输和贮存。 本文件适用于以甲醇为燃料，以水为传热介质，额定供热量小于40 kW，额定工作压力为常压或最大采暖工作压力不大于0.3 MPa，工作时水温不高于85℃的民用采暖炉。

Civil methanol heating stove

13/30277394 DC BS EN 1. 带汽化燃烧器的燃油炉

BS EN 1. Flued oil stoves with vaporizing burners

ANSI/UL 296A-2013 废油燃烧空气加热设施安全性标准

Standard for Safety for Waste Oil-Burning Air-Heating Appliances

NF D35-386:2009 乙醇动力设备 安全要求和测试方法

Appareils fonctionnant à l'éthanol - Exigences de sécurité et méthodes d'essai

JIS S 2073:2009 民用直排风式燃油加热器的标准使用条件,标准加速模式和测试条件

Standard use conditions, standard acceleration mode and test conditions for domestic direct vent type oil burning space heater

JIS S 2031:2009 密封型燃油空间加热器

Closed type oil burning space heaters

JIS S 2036:2009 开放式强制通风燃油空间加热器

Open type forced ventilating oil burning space heaters

JIS S 2019:2009 开放式自然通风燃油空间加热器

Open type natural ventilating oil burning space heaters

JIS S 2039:2009 半密闭式燃油空间加热器

Semi closed type oil burning space heaters

JIS A 4003 AMD 1:2009 热风炉(修改件1)

This translation has been made based on the Amendment to the origi- nal Japanese Industrial Standard revised by the Minister of Economy, Trade and Industry through deliberations at the Japanese Industrial Standards Committee as the result of proposal for revision of Japanese Industrial Standard with the draft being attached, based on the provi- sion of Article 12 Clause 1 of the Industrial Standardization Law ap- plicable to the case of revision by the provision of Article 14. Consequently, JIS A 4003:1995 is partially replaced with this Amend- ment.

Warm air furnaces (Amendment 1)

JIS B 8416 AMD 1:2009 工业用便携型燃油空间加热器(修改件1)

This translation has been made based on the Amendment to the origi- nal Japanese Industrial Standard revised by the Minister of Economy, Trade and Industry through deliberations at the Japanese Industrial Standards Committee as the result of proposal for revision of Japanese Industrial Standard with the draft being attached, based on the provi- sion of Article 12 Clause 1 of the Industrial Standardization Law ap- plicable to the case of revision by the provision of Article 14. Consequently, JIS B 8416:1992 is partially replaced with this Amend- ment.

Portable type oil burning space heaters for industrial use (Amendment 1)

ANSI/NFPA 289-2009 单个燃料包防火性能特性测定用防火试验的标准方法

This document describes a method of determining the contribution of individual fuel packages to heat and smoke release in a room environment, and is applicable to individual fuel packages that do not exceed 2.4m high by 2.4m wide by 2.4m deep in dimensions. This document specified three types of specimen mounting, depending on the fuel package to be investigated, as follows: (1) single decorative object, including combustible vegetation; (2) exhibit booth; and (3) stage settings.

Standard Method of Fire Test for Determining the Fire Performance Characteristics of Individual Fuel Packages

LST EN 15034-2007/AC-2008 采暖锅炉-燃油冷凝式采暖锅炉

Heating boilers - Condensing heating boilers for fuel oil

DS/EN 1/A1/ZA:2008 带汽化燃烧器的烟油炉

This standard applies to flued oil stoves with one or more vaporizing burners as used for individual heating in the domestic field and having either a draught regulator or a combustion air limiter as defined in 3.13 and a nominal heating capacity of not more than 15 kW. It is not applicable for built-in equipment.

Flued oil stoves with vaporizing burners

ANSI/UL 730-2008 燃油壁炉的安全标准

The following topics are being recirculated: 1. Removal of Dates from References 2. Identification of Equipment Grounding Conductor

Standard for Safety for Oil-Fired Wall Furnances

ANSI/UL 729-2008 燃油地板炉的安全标准

The following changes in requirements are being proposed: 1. Removal of Dates from References 2. Identification of Equipment Grounding Conductor 3. Identification of Neutral Conductor 4. Replacement of Reference to ASTM A525 with ASTM A653 5. Corrections to Referenced Codes and Standards 6. Updates to Standards for Components for Switches

Standard for Safety for Oil-Fired Floor Furnaces

DIN EN 1:2007 带有蒸气燃烧器的燃油炉

This standard applies to flued oil stoves with one or more vaporizing burners (hereafter referred to as "stoves") as used for individual heating in the domestic field and having either a draught regulator or a combustion air limiter as defined in 3.13 and a nominal heating capacity of not more than 15 kW. This standard also applies to appliances with fan assisted vaporizin9 burners. This standard does not cover -- Built-in appliances -- appliances equipped with an atomizing burner appliances incorporating a boiler or connected to a water system. According to the type of fuels used in the country of destination, the stoves are supplied for use with either: fuel oil with a maximum kinematic viscosity of 6,0 mm/s at 20 ℃ or kerosene with a flash point of not less than 40 ℃.

Flued oil stoves with vaporizing burners(includes Amendment A1:2007); English version of DIN EN 1:2007-12