97.150 铺地非织物 标准查询与下载

KS K ISO 16905-2019 弹性地板 - 橡胶地板覆盖物的规格 - 瓷砖/木板

Resilient floor coverings — Specification for rubber floor covering — Tile/Plank

KS K ISO 10577:2019 弹性地板 - 橡胶板地板覆盖物无背衬的规格

Resilient floor coverings — Specification for rubber sheet floor coverings without backing

KS K ISO 10575-2019 弹性地板 - 橡胶板地板覆盖物背衬规格

Resilient floor coverings — Specification for rubber sheet floor coverings with backing

KS K ISO 14486:2019 层压板地板 - 规格

Laminate floor coverings — Specification

KS K ISO 10577-2019 弹性地板 - 橡胶板地板覆盖物无背衬的规格

Resilient floor coverings — Specification for rubber sheet floor coverings without backing

KS K ISO 10575:2019 弹性地板 - 橡胶板地板覆盖物背衬规格

Resilient floor coverings — Specification for rubber sheet floor coverings with backing

KS K ISO 20326:2019 弹性地板覆盖物 - 松散铺设的地板/装配规范

Resilient floor coverings — Specification for floor panels/assembly for loose laying

KS K ISO 14486-2019 层压板地板 - 规格

Laminate floor coverings — Specification

ASTM E648-19a 使用辐射热源的地板覆盖系统临界辐射通量的标准试验方法

Standard Test Method for Critical Radiant Flux of Floor-Covering Systems Using a Radiant Heat Energy Source

ASTM E648-19ae1 使用辐射热源的地板覆盖系统临界辐射通量的标准试验方法

1.1 This fire-test-response standard covers a procedure for measuring the critical radiant flux of horizontally mounted floor-covering systems exposed to a flaming ignition source in a graded radiant heat energy environment in a test chamber. A specimen is mounted over underlayment, a simulated concrete structural floor, bonded to a simulated structural floor, or otherwise mounted in a typical and representative way. 1.2 This fire-test-response standard measures the critical radiant flux at flame-out. It provides a basis for estimating one aspect of fire exposure behavior for floor-covering systems. The imposed radiant flux simulates the thermal radiation levels likely to impinge on the floors of a building whose upper surfaces are heated by flames or hot gases, or both, from a fully developed fire in an adjacent room or compartment. The standard was developed to simulate an important fire exposure component of fires that develop in corridors or exitways of buildings and is not intended for routine use in estimating flame spread behavior of floor covering in building areas other than corridors or exitways. See Appendix X1 for information on proper application and interpretation of experimental results from use of this test. 1.3 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.4 The text of this standard references notes and footnotes that provide explanatory information. These notes and footnotes, excluding those in tables and figures, shall not be considered as requirements of this standard. 1.5 This standard is used to measure and describe the response of materials, products, or assemblies to heat and flame under controlled conditions but does not by itself incorporate all factors required for fire-hazard or fire-risk assessment of materials, products, or assemblies under actual fire conditions. 1.6 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.Specific hazard statements are given in Section 7. 1.7 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Method for Critical Radiant Flux of Floor-Covering Systems Using a Radiant Heat Energy Source

BS EN 16641:2019 纺织地板覆盖物 可接受的颜色偏差指南

What is BS EN 16641 - colour deviations of textile floor covering about?    BS EN 16641 discusses colour deviations of textile floor covering. BS EN 16641 gives guidance in case of complaints when a colour deviation is observed after installation of a textile floor covering by the installer and/or end-user.   The colour deviation can be observed within different parts of the installation or between the installed textile floor covering and the initially presented sample on which the choice for ordering was made.   Who is BS EN 16641 -

Textile floor coverings. Guidelines for acceptable colour deviations

ISO 10581:2019 弹性地板 均质聚（氯乙烯）地板覆盖层 规格

This document specifies the characteristics of homogeneous floor coverings, based on poly(vinyl chloride), supplied in either tile or roll form. Products can contain a transparent, non-PVC factory finish. To encourage the consumer to make an informed choice, this document also includes a classification system (see ISO 10874) based on intensity of use, which shows where these floor coverings give satisfactory service. It also specifies requirements for marking.

Resilient floor coverings — Homogeneous poly(vinyl chloride) floor covering — Specifications

T/CADBM 20-2019 弹性地板应用技术规则

本规程的主要技术内容是:1.总则;2.术语;3.基本规定;4.材料;5.设计;6.施工;7.质量验收。

Technical rules for the application of resilient flooring

ISO 24337:2019 层压地板覆盖物.几何特性的测定

This document gives test methods to determine the dimensional variance between elements of laminate floor coverings in a manufactured free-standing shape (unrestricted) in respect of thickness, length, width, squareness, straightness, width flatness, length flatness, openings between assembled elements and height differences between assembled elements. NOTE These test methods are also applicable to other mechanically assembled panels, e.g. modular multilayer floorings.

Laminate floor coverings — Determination of geometrical characteristics

ASTM F3311-19 安装前弹性地板系统部件性能和兼容性的垫子粘合评定的标准实施规程

1.1 This practice is designed to provide a short-term qualitative evaluation of the effectiveness and compatibility of the composite layers for flexible and fully adhered resilient flooring installation(s). Aspects of the resilient flooring assembly to be evaluated may include concrete surface profile (CSP), surface preparation, a topical moisture mitigation system, underlayment product(s), primer(s), application and the installation of the resilient flooring material itself. Aspects such as surface profile, surface cleanliness, surface porosity, the application method(s), and the open, curing, and drying times of each layer of the flooring system can be assessed using this practice prior to the actual full-scale installation taking place. 1.1.1 This practice is not intended for use with liquid applied, loose laid or perimeter fixed, or rigid resilient flooring products. 1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. See Section 6 for specific Hazards statements. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Practice for Mat Bond Evaluation of Performance and Compatibility for Resilient Flooring System Components Prior to Installation

KS K ISO 10833-2019 纺织地板覆盖物 - 使用改进的Vettermann鼓测试确定切割边缘的抗损伤性

Textile floor coverings — Determination of resistance to damage at cut edges using the modified Vettermann drum test

KS K ISO 10833:2019 纺织地板覆盖物 - 使用改进的Vettermann鼓测试确定切割边缘的抗损伤性

Textile floor coverings — Determination of resistance to damage at cut edges using the modified Vettermann drum test

ASTM F1913-19 乙烯基板地板覆盖无背衬的标准规范

1.1 This specification covers sheet floor covering having a vinyl wear layer without backing. Products also may contain a clear specialty performance top layer(s). 1.2 This type of floor covering is intended for use in commercial and light commercial buildings. General information and performance characteristics, which determine serviceability and recommended use, are included in this specification. 1.3 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Vinyl Sheet Floor Covering Without Backing

BS ISO 24334:2019 层压地板覆盖物 机械组装面板锁定强度的测定

What is ISO 24334 - D etermination of the locking strength of laminate floor covering panels about?    ISO 24334 discusses the method for the determination of the locking strength of laminate floor covering panels.   ISO 24334 specifies a method for determination of the locking strength of joints between the laminate floor covering panels which are assembled with both vertical and horizontal mechanical locking systems.   Note: ISO 24334 is also applicable to other mechanically assembled panels, e.g., modular multilayer floorings.  Who is ISO 24334 - D etermination of the locking strength of laminate floor covering panels for?   ISO 24334 on determination of...

Laminate floor coverings. Determination of locking strength for mechanically assembled panels

BS EN 686:2019 弹性地板覆盖物 泡沫背衬上的普通和装饰油毡规范

What is BS EN 686 - Specification for plain and decorative linoleum on a foam backing about?    BS EN 686 discusses r esilient floor coverings.   BS EN 686 specifies the characteristics of plain and decorated linoleum on a foam backing as a compound floor covering, supplied in roll form.   To encourage the consumer to make an informed choice, BS EN 686 includes a classification system based on the intensity of use, which shows where resi...

Resilient floor coverings. Specification for plain and decorative linoleum on a foam backing