97.200.99 其他文娱活动设备 标准查询与下载

ASTM F2974-24a 审核游乐设施和设备的标准规范

1.1  This practice establishes minimum requirements for auditing conformance to ASTM Committee F24 Standards during an audit of an amusement ride or device within a defined scope. 1.2  Defined scope of audit shall include but not be limited to the following: 1.2.1  Auditors sufficient relevant education, training, technical knowledge, certifications as appropriate, and experience to properly audit an amusement ride or device in accordance with subsection 5.1 of this standard. 1.2.2  Visual acuity requirements (if applicable) in accordance with subsection 5.1.3 of this standard. 1.2.3  Reference standards including published year. 1.3  This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.4  This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Practice for Auditing Amusement Rides and Devices

ASTM F770-24 游乐设施和设备的所有权、操作、维护和检验的标准实施规程

Standard Practice for Ownership, Operation, Maintenance, and Inspection of Amusement Rides and Devices

ASTM F1193-24 游乐设施和设备的质量、制造和施工标准实施规程

Standard Practice for Quality, Manufacture, and Construction of Amusement Rides and Devices

T/QGCML 2045-2023 便捷式宣传栏

本文件规定了便捷式宣传栏的产品结构、技术要求、试验方法、检验规则、标志、包装、运输及贮存。 本文件适用于便捷式宣传栏的生产和检验。

Convenient bulletin board

T/ZSM 0030-2023 麻质飞镖靶（盘）

本文件规定了麻质飞镖靶（盘）（以下简称“麻靶”）的产品分类、要求、试验方法、检验规则、标志、包装、运输和贮存。 本文件适用于飞镖运动中使用的麻靶。

Sisal dartboard

ASTM F3054-23 铁路游乐设施、装置和设施运营的标准实施规程

1.1  This practice applies to operations of amusement railway ride(s) that have a track gauge greater than or equal to 12 in. (305 mm) measured between the heads of the rails. This excludes patron powered ride vehicles specifically designed for children. 1.2  This standard does not apply to the operation of rides, such as roller coasters, that resemble railways, but fall within the scope of Practice F2291 -22a or Practice F1159 -16ε1. This standard also does not apply to funiculars as defined in ANSI B77.2-20 or BS EN 1907-17. 1.3  This standard does not apply to amusement railway rides operation that are intended for use as a portable amusement ride or attraction. 1.4  This standard does not apply to permanently installed amusement railway rides and tourist railways, and their associated track, devices and facilities that are under the jurisdiction of the Federal Railroad Administration (FRA) in whole or part or national equivalent. 1.5  The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.6  This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.7  This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Practice for Operations of Amusement Railway Rides, Devices, and Facilities

ASTM F2960-23 永久娱乐铁路轨道及相关设备的标准实施规程

1.1  This standard applies to design, manufacture, installation, operation, maintenance, and inspection of permanent amusement railway ride(s) that have a track gauge greater than or equal to 12 in. (305 mm) measured between the heads of the rails and their related devices and facilities, for example, bridges, tunnels, and signal support structures, excluding rolling stock. This “track” specific standard provides requirements which are not covered in the “core” or “supporting” standards of the ASTM F24 committee. 1.2  This standard does not apply to track rides, such as roller coasters, that may resemble railways. 1.3  This standard does not apply to funiculars as defined in ANSI B77.2 (2020) or BS EN 1907 (2017). 1.4  This standard does not apply to Amusement Railway Rides and their associated track, devices and facilities that are manufactured and intended for use as a portable amusement ride or attraction. 1.5  This standard does not apply to permanently installed amusement railway rides and tourist railways, and their associated track, devices and facilities that are under the jurisdiction of the United States Federal Railroad Administration (FRA) in whole or part, or national equivalent. 1.6  This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.7  This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Practice for Permanent Amusement Railway Ride Tracks and Related Devices

ASTM F1193-23 游乐设施和设备的质量、制造和施工的标准实施规程

1.1  This practice establishes the minimum requirements for a quality assurance program and the manufacturing of amusement rides and devices (including major modifications). 1.2  This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.3  This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Practice for Quality, Manufacture, and Construction of Amusement Rides and Devices

ASTM F770-23 游乐设施和设备的所有权、操作、维护和检查的标准实施规程

1.1 This practice provides guidelines for operations, maintenance, and inspection procedures for amusement rides and devices to be performed by the owner/operator. 1.2 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.3 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Practice for Ownership, Operation, Maintenance, and Inspection of Amusement Rides and Devices

ANSI/CAN/UL 8400:2023 虚拟现实、增强现实和混合现实技术设备

This Standard addresses the safety of electrical and electronic equipment within the field of virtual reality, augmented reality and mixed reality technologies with a rated voltage not exceeding 600 V. EXAMPLE VR/AR/MR head-mounted displays, holographic displays, AR/MR smart glasses, hand-held VR/AR/MR devices and interactive virtual simulators. Particular aspects addressed by this Standard include the means to reduce, as far as practicable, the effects of visually induced motion sickness, visual opacity, flicker, skin sensitization, heat exposure to the eye, biomechanical stress and optical occlusion to some extent. This Standard does not address the following: – psychological effects, such as modification of phobias and enhancement or repression of emotions, – neurological effects on the visual systems, such as modification of stereoscopic vision, and visual acuity, and – vestibular disturbances, such as nausea and vomiting. This Standard is intended to supplement the requirements addressing risk of electrical shock, fire, thermal burn, and other general product safety aspects that are already covered by the CAN/CSA-C22.2 No. 62368-1/UL 62368-1 requirements for wearable equipment. Annex D summarizes these aspec

Virtual Reality, Augmented Reality and Mixed Reality Technology Equipment

T/CSTM 00952-2023 景区玻璃类游乐和观景设施用玻璃承载性能测试方法

本文件规定了景区玻璃类游乐和观景设施（以下简称“玻璃类设施”）用玻璃承载性能测试方法的术语和定义、测试原理、测试试样、测试装置、测试条件、测试程序、数据记录、结果计算、结果评定和测试报告。 本文件适用于新建的和在用的玻璃水滑道、玻璃滑道、玻璃悬索桥、玻璃步道、玻璃观景台（塔）等玻璃类设施用玻璃承载性能的测试与评价。 其他相近结构可参照本文件执行。

Test method for load-bearing performance of glass for attraction glass amusement and viewing facility

BS ISO 20187-2:2022 充气游乐设备 用于永久安装的充气弹跳枕的附加安全要求

1   Scope This part of ISO 20187 specifies additional safety requirements for inflatable bouncing pillows intended for permanent installation. This part of ISO 20187 is applicable to inflatable play equipment intended for use by children fourteen years and under, both individually and collectively. This part of ISO 20187 specifies safety requirements for inflatable play equipment for which the primary activity is bouncing. It sets measures to address risks and also to minimize accidents to users for those involved in the design, manufacture and supply of inflatable play equipment. It specifies information to be supplied with the equipment. The requirements have been laid down bearing in mind the risk factor based on available data. This part of ISO 20187 specifies the requirements that will protect a child from hazards that he or she might be unable to foresee when using the equipment as intended, or in a manner that can be reasonably anticipated. This part of ISO 20187 is not applicable to inflatables dealt with in ISO 20187‑1:2022, inflatable water-borne play and leisure equipment, domestic inflatable toys, air-supported buildings, inflatables used solely for protection, inflatables used for rescue, or other types of inflatable toys where the primary activity is not bouncing or sliding.

Inflatable play equipment - Additional safety requirements for inflatable bouncing pillows intended for permanent installation

BS ISO 20187-3:2022 充气游乐设备 snappies 的附加安全要求和测试方法

1   Scope This part of ISO 20187 is applicable to inflatable play equipment intended for use by children fourteen years and under, both individually and collectively. This part of ISO 20187 specifies additional safety requirements for snappies for which the primary activities are climbing and sliding. It sets measures to address risks and also to minimize accidents to users for those involved in the design, manufacture and supply of inflatable play equipment. It specifies information to be supplied with the equipment. The requirements have been laid down bearing in mind the risk factor based on available data. This part of the ISO 20187 specifies requirements to protect a child from hazards that he or she might be unable to foresee when using the equipment as intended, or in a manner that can be reasonably anticipated. This part of the ISO 20187 is not applicable to inflatable water-borne play and leisure equipment, domestic inflatable toys, air-supported buildings, inflatables used solely for protection, inflatables used for rescue, or other types of inflatable toys where the primary activity is not bouncing or sliding.

Inflatable play equipment - Additional safety requirements and test methods for snappies

BS ISO 20187-1:2022 充气游乐设备安全要求和测试方法

Inflatable play equipment - Safety requirements and test methods

ISO 20187-2:2022 充气游戏设备.第2部分:永久安装充气弹跳枕的附加安全要求

This part of ISO 20187 specifies additional safety requirements for inflatable bouncing pillows intended for permanent installation. This part of ISO 20187 is applicable to inflatable play equipment intended for use by children fourteen years and under, both individually and collectively. This part of ISO 20187 specifies safety requirements for inflatable play equipment for which the primary activity is bouncing. It sets measures to address risks and also to minimize accidents to users for those involved in the design, manufacture and supply of inflatable play equipment. It specifies information to be supplied with the equipment. The requirements have been laid down bearing in mind the risk factor based on available data. This part of ISO 20187 specifies the requirements that will protect a child from hazards that he or she might be unable to foresee when using the equipment as intended, or in a manner that can be reasonably anticipated. This part of ISO 20187 is not applicable to inflatables dealt with in ISO 20187-1:2022, inflatable water- borne play and leisure equipment, domestic inflatable toys, air-supported buildings, inflatables used solely for protection, inflatables used for rescue, or other types of inflatable toys where the primary activity is not bouncing or sliding.

Inflatable play equipment — Part 2: Additional safety requirements for inflatable bouncing pillows intended for permanent installation

ISO 20187-1:2022 充气游戏设备.第1部分:安全要求和试验方法

This document is applicable to inflatable play equipment intended for use by children fourteen years and under both individually and collectively. This document specifies safety requirements for inflatable play equipment for which the primary activities are bouncing and sliding. It sets measures to address risks and also to minimize accidents to users for those involved in the design, manufacture and supply of inflatable play equipment. It specifies information to be supplied with the equipment. The requirements have been laid down bearing in mind the risk factor based on available data. This document specifies the requirements that will protect a child from hazards that he or she may be unable to foresee when using the equipment as intended, or in a manner that can be reasonably anticipated. This document is not applicable to inflatable water-borne play and leisure equipment, domestic inflatable toys, air-supported buildings, inflatables used solely for protection, inflatables used for rescue, or other types of inflatable toys where the primary activity is not bouncing or sliding.

Inflatable play equipment — Part 1: Safety requirements and test methods

ISO 20187-3:2022 充气游戏设备.第3部分:笛鲷的附加安全要求和试验方法

This part of ISO 20187 is applicable to inflatable play equipment intended for use by children fourteen years and under, both individually and collectively. This part of ISO 20187 specifies additional safety requirements for snappies for which the primary activities are climbing and sliding. It sets measures to address risks and also to minimize accidents to users for those involved in the design, manufacture and supply of inflatable play equipment. It specifies information to be supplied with the equipment. The requirements have been laid down bearing in mind the risk factor based on available data. This part of the ISO 20187 specifies requirements to protect a child from hazards that he or she might be unable to foresee when using the equipment as intended, or in a manner that can be reasonably anticipated. This part of the ISO 20187 is not applicable to inflatable water-borne play and leisure equipment, domestic inflatable toys, air-supported buildings, inflatables used solely for protection, inflatables used for rescue, or other types of inflatable toys where the primary activity is not bouncing or sliding.

Inflatable play equipment — Part 3: Additional safety requirements and test methods for snappies

T/GAMA 25-2022 增材制造 运动头盔缓冲层技术要求

文件规定了增材制造（3D打印）领域制造的运动头盔缓冲层产品（以下简称“产品”）的规格、技术要求、试验方法、检验规则、标志、包装、运输、贮存

Additive manufacturing - Technical requirements for the cushioning layer of sports helmets

ASTM F1193-22 游乐设施和设备的质量、制造和建造的标准实施规程

1.1 This practice establishes the minimum requirements for a quality assurance program and the manufacturing of amusement rides and devices (including major modifications). 1.2 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.3 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Practice for Quality, Manufacture, and Construction of Amusement Rides and Devices

ASTM F2974-22 游乐设施和装置的审计标准实施规程

1.1 This practice establishes minimum requirements for auditing conformance to ASTM Committee F24 Standards during an audit of an amusement ride or device within a defined scope. 1.2 Defined scope of audit shall include but not be limited to the following: 1.2.1 Auditors sufficient relevant education, training, technical knowledge, certifications as appropriate, and experience to properly audit an amusement ride or device in accordance with subsection 5.1 of this standard. 1.2.2 Visual acuity requirements (if applicable) in accordance with subsection 5.1.3 of this standard. 1.2.3 Reference standards including published year. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Practice for Auditing Amusement Rides and Devices