97.220.20 标准查询与下载

KS G ISO 9462-2018(2023) 高山滑雪板捆绑件要求和试验方法

Alpine ski-bindings — Requirements and test methods

KS G ISO 11110:2018 冬季运动器材 - 测试设备功能单元的设置滑雪/启动/绑定 - 要求和测试

Winter-sports equipment — Test devices for the setting of the functional unit ski/boot/binding — Requirements and tests

KS G ISO 11087:2018 高山滑雪板固定装置要求和试验方法

Alpine ski-bindings — Retention devices — equirements and test methods

KS G ISO 11087-2018(2023) 高山滑雪板固定装置要求和试验方法

Alpine ski-bindings — Retention devices — equirements and test methods

KS G ISO 9462:2018 高山滑雪绑定 - 要求和测试方法

Alpine ski-bindings — Requirements and test methods

KS G ISO 11110-2018 冬季运动器材 - 测试设备功能单元的设置滑雪/启动/绑定 - 要求和测试

Winter-sports equipment — Test devices for the setting of the functional unit ski/boot/binding — Requirements and tests

KS G ISO 11110-2018(2023) 冬季运动器材滑雪板/滑雪靴/捆绑功能装置的试验装置要求和试验

Winter-sports equipment — Test devices for the setting of the functional unit ski/boot/binding — Requirements and tests

KS G ISO 11087-2018 高山滑雪板固定装置要求和试验方法

Alpine ski-bindings — Retention devices — equirements and test methods

DIN ISO 11088:2018 高山滑雪板/固定器/靴子（SBB）系统 组装、调整和检查（ISO 11088:2018）

This document specifies assembly, adjustment and inspection procedures for the binding mechanisms of skis, integrating, in a practical way, the requirements of those International Standards which are related to skis, bindings and boots. It is intended for all individuals and institutions concerned with those procedures, and especially for sports retailers. It is applicable to a ski-binding-boot system (S-B-B) for alpine skiing, of which at least one component is owned by the user. This document is applicable to complete and incomplete alpine ski-binding-boot systems which are owned by the user or rented for 15 days or more. NOTE ISO 13993 gives a method of measurement for equipment which is rented for less than 15 days.

Alpine ski/binding/boot (S-B-B) system - Assembly, adjustment and inspection (ISO 11088:2018)

NF S52-719*NF ISO 7139:2018 速度滑雪板.弹性的测定

Le présent document spécifie des méthodes de mesure en laboratoire permettant de déterminer les caractéristiques élastiques des skis de fond. Il a pour but de permettre de calculer la résistance à la flexion de parties déterminées du ski.

Cross-country skis - Determination of elastic properties

ASTM F1063-09(2018) 高山滑雪/捆绑/引导系统功能检查和调整的标准实施规程

Standard Practice for Functional Inspections and Adjustments of Alpine Ski/Binding/Boot Systems

ASTM F779-12(2018) 高山滑雪板扭转特性的标准试验方法

1.1 This test method covers the measurement of ski forebody torsion and ski afterbody torsion of adult Alpine skis. 1.2 No limitation to ski size is proposed. This test method is applicable to all Alpine skis. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Method for Torsion Characteristic of Alpine Skis

ASTM F2546-07(2018) 滑雪板步进式绑带的标准测试方法

1.1 This test method specifies the essential requirements for a snowboard step-in binding—boot system (see 3.1.2); hereafter referred to as step-in snowboard bindings. 1.2 This test method is applicable to step-in snowboard bindings for adults and children. This type of binding system utilizes a mechanical interlocking mechanism, and the interlock mechanism of the system will be specific to the particular manufacturer. Compatibility between different systems is not expected or anticipated thus each potential combination of boot and binding requires testing. 1.3 For snowboard boots interfacing with ski binding, see ISO 11634. 1.4 For snowboard plate bindings, see ISO 14790. 1.5 For snowboard strap bindings made for soft boots, see ISO 14573. 1.6 For snowboard step-in bindings, see ISO 15344. 1.7 This standard does not address how or under what circumstances a snowboard binding with programmable release modes should release in its intended modes nor does it address the safety, desirability, or efficacy of any programmable release mode for snowboard bindings; any testing of such bindings to this standard must be performed with the release modes disabled or adjusted to their highest release value. 1.8 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.9 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Method for Snowboard Step-in Bindings

ASTM F780-93a(2018) 高山滑雪板线性变形和断裂强度的标准试验方法

1.1 This test method covers the determination of linear deformation load and breaking load for Alpine skis.2 1.2 This test method is applicable to all Alpine skis. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Method for Linear Deformation and Breaking Strength of Alpine Skis

DIN ISO 7798:2018 越野雪橇.疲劳指标的测定.周期性载荷试验(ISO 7798-2017)

This document specifies a method for the determination of the fatigue indexes of cross-country skis (i.e. the resistance of the skis to changes of bottom camber height or irreversible damage) after a bending test with cyclic loading. It is applicable to cross-country skis with a nominal length of 160 cm to 215 cm.

Cross-country skis - Determination of fatigue indexes - Cyclic loading test (ISO 7798:2017)

ISO 11088:2018 高山雪橇/连接装置/靴系统.装配、调整和检验

This document specifies assembly, adjustment and inspection procedures for the binding mechanisms of skis, integrating, in a practical way, the requirements of those International Standards which are related to skis, bindings and boots. It is intended for all individuals and institutions concerned with those procedures, and especially for sports retailers. It is applicable to a ski-binding-boot system (S-B-B) for alpine skiing, of which at least one component is owned by the user. This document is applicable for complete and incomplete alpine ski-binding-boot systems which are owned by the user or rented for 15 days or more. NOTE ISO 13993 gives a method of measurement for equipment which is rented for less than 15 days.

Alpine ski/binding/boot (S-B-B) system - Assembly, adjustment and inspection

BS ISO 6003:2017 高山滑雪. 质量和极惯性矩的确定. 实验室测量法

Alpine skis. Determination of mass and polar moment of inertia. Laboratory measurement method

ASTM F939-18 选择高山滑雪绑定释放扭矩值的标准实践

Standard Practice for Selection of Release Torque Values for Alpine Ski Bindings

BS ISO 8364:2017 高山滑雪板和固定器 绑定安装区域 要求及测试方法

1   Scope This document specifies requirements and test methods for the binding mounting area and free space area , ski bindings and retention devices of alpine skis, in order to optimize the compatibility of the functional unit “ski binding — retention device — boot”. It contains data for the manufacturer of alpine skis, bindings and retention devices, concerning dimensions, tests and other specifications for the binding mounting area .

Alpine skis and bindings. Binding mounting area. Requirements and test methods

BS ISO 7139:2017 越野滑雪板 弹性性能的测定

1   Scope This document specifies laboratory measurement methods to determine the elastic properties of cross-country skis. Its purpose is to calculate the resistance of defined parts of the ski to bending. This document applies to cross-country skis with a nominal length greater than or equal to 150 cm. The standard measurement procedures can be used to ensure comparability between laboratory measurement data, determined and published by ski manufacturers, institutions or others. In this document, no attempt is made to relate the measurement data to the quality of the ski.

Cross-country skis. Determination of elastic properties