C73 劳动防护用品 标准查询与下载

DIN EN ISO 15027-2:2013 浸水服装.第2部分:废弃服装,含安全性要求(ISO 15027-2-2012).德文版本EN ISO 15027-2-2012

Immersion suits - Part 2: Abandonment suits, requirements including safety (ISO 15027-2:2012); German version EN ISO 15027-2:2012

DIN EN ISO 15027-1:2013 浸水服装.第1部分:常穿服装、含安全性要求(ISO 15027-1-2012).德文版本EN ISO 15027-1-2012

Immersion suits - Part 1: Constant wear suits, requirements including safety (ISO 15027-1:2012); German version EN ISO 15027-1:2012

DIN EN ISO 20344:2013 个人防护装备.鞋靴的试验方法(ISO 20344-2011).德文版本EN ISO 20344-2011

Personal protective equipment - Test methods for footwear (ISO 20344:2011); German version EN ISO 20344:2011

DIN EN ISO 13287:2013 个人防护装备.鞋靴.防滑性试验方法(ISO 13287-2012).德文版本EN ISO 13287-2012

Personal protective equipment - Footwear - Test method for slip resistance (ISO 13287:2012); German version EN ISO 13287:2012

ISO 6529:2013 防护服.化学品的防护.防护服耐液体和气体渗透性的测定

This International Standard describes laboratory test methods to determine the resistance of materials used in protective clothing, including gloves and including footwear, when the footwear is an integral part of the clothing, to permeation by liquid or gaseous chemicals under the conditions of either continuous or intermittent contact. Method A is applicable to testing against liquid chemicals, either volatile or soluble in water, expected to be in continuous contact with the protective clothing material. Method B is applicable to testing against gaseous chemicals expected to be in continuous contact with the protective clothing material. Method C is applicable to testing against gaseous and liquid chemicals, either volatile or soluble in water, expected to be in intermittent contact with the protective clothing material. These test methods assess the permeation resistance of the protective clothing material under laboratory conditions in terms of breakthrough time, permeation rate and cumulative permeation. These test methods also enable qualitative observations to be made of the effects of the test chemical on the material under test. These test methods are only suitable for measuring permeation by liquids and gases. Permeation by solid challenge chemicals is beyond the scope of this International Standard. NOTE It can be difficult or impossible to normalize the results of permeation tests carried out against solid challenge chemicals. The normalized rate of permeation is dependent on the area of fabric exposed to the challenge chemical. In the case of solids this will, in turn, depend also on factors such as particle size, size distribution, particle shape and packing considerations. These test methods address only the performance of materials or certain materials’ constructions (e.g. seams). These test methods do not address the design, overall construction and components, or interfaces of garments, or interfaces between garments and gloves or garments and footwear, or other factors which may affect the overall chemical protection offered by protective clothing, gloves or footwear or combinations of chemical protective clothing, gloves and footwear. It is emphasized that these tests do not necessarily simulate conditions to which materials are likely to be exposed in practice. In most cases the conditions of the permeation test will be far more challenging than expected workplace conditions.

Protective clothing - Protection against chemicals - Determination of resistance of protective clothing materials to permeation by liquids and gases

ANSI/ASTM F1446:2013 评定安全防护帽功能特性用设备和规程的测试方法

Test Methods for Equipment and Procedures Used in Evaluating the Performance Characteristics of Protective Headgear

ANSI/ASTM F2122:2013 树架安全装置用实施规程

PRACTICE FOR TREESTAND SAFETY DEVICES

ASTM F2962-13 杀虫剂施药人员穿的防护服的合格评定的标准实施规程

1.1 This practice establishes the conformity assessment requirements for limited use and reusable garments that are worn while spraying field strength liquid pesticides. The testing requirements for supplier’s declaration of conformity and certification are specified in Specification F2669. 1.2 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Practice for Conformity Assessment of Protective Clothing Worn by Operators Applying Pesticides

ASTM F1494-13 防护服相关标准术语

1.1 This standard defines the specialized terms used in standards developed by Committee F23 on Protective Clothing. 1.2 Definitions of Terms, which were drafted for use only in a single standard, are also included for convenient reference. Under ASTM rules they may become full definitions in the future, if they are used in additional standards. 1.3 Additional terminology relevant to protective clothing and to the components of protective clothing can be found in Terminology D123, D1566, and D4805.

Standard Terminology Relating to Protective Clothing

ANSI/ASSE Z359.13-2013 个人能量吸收器和能量吸收绳索

Personal Energy Absorbers and Energy Absorbing Lanyards

ASTM F1671/F1671M-13 使用Phi-X174噬菌体渗透作为试验系统的血源性病原体对防护服使用的抗渗透材料用标准试验方法

5.1 This test method is based on Test Method F903 for measuring resistance of chemical protective clothing materials to penetration by liquids. This test method is normally used to evaluate specimens from individual finished items of protective clothing and individual samples of materials that are candidates for items of protective clothing. 5.1.1 Finished items of protective clothing include gloves, arm shields, aprons, gowns, coveralls, hoods, and boots. 5.1.2 The phrase “specimens from finished items” encompasses seamed and other discontinuous regions, as well as the usual continuous regions of protective clothing items. 5.2 It is known that body fluids penetrating protective clothing materials are likely to carry microbiological contaminants; however, visual detection methods are not sensitive enough to detect minute amounts of liquid containing microorganisms (1,2,3).8 This test method uses media containing Phi-X174 Bacteriophage. The visual detection technique of this test method is supplemented with a biologically based assay capable of detecting virus under the specified test conditions. 5.3 Test Method F1670, allows the screening of protective clothing materials for resistance to penetration with synthetic blood as a challenge liquid. Test Method F1670 uses the same penetration test cell and technique, but exposes material specimens to synthetic blood with visual detection of liquid penetration. Materials passing Test Method F1670 should then be tested against bacteriophage penetration using this test method to verify performance. 5.4 This test method has been specifically designed for measuring penetration of a surrogate microbe for Hepatitis (B and C) and the Human Immunodeficiency Viruses. The surrogate, Phi-X174 Bacteriophage, used in this test method is similar to HCV in size and shape but also serves as a surrogate for HBV and HIV. Inferences about protection from other pathogens must be assessed on a case-by-case basis. 5.5 Part of the protocol in Procedure A and B in Table 1, for exposing the protective clothing material specimens to the Phi-X174 Bacteriophage challenge suspension, involves pressurization of the penetration cell to 13.8 kPa [2 psig]. This hydrostatic pressure has been documented to discriminate between protective clothing material performance and correlate with visual penetration results that are obtained with a human factors validation (4). Some studies, however, suggest that me......

Standard Test Method for Resistance of Materials Used in Protective Clothing to Penetration by Blood-Borne Pathogens Using Phi-X174 Bacteriophage Penetration as a Test System

ASTM F1359/F1359M-13 服装模特所穿防护服或者防护衣在淋浴喷头下耐液体渗透性的标准试验方法

5.1 This test method evaluates the ability of the construction and configuration of protective clothing or protective ensembles to resist liquid penetration. In most cases, the conditions used in this test method will not represent actual end-use conditions. 5.2 The one-hour duration of the test is not intended to simulate user exposure to splashes of liquid chemical but rather to provide sufficient time for enough liquid to penetrate to make visual detection easier. 5.2.1 It is permissible to specify shorter test durations. The duration of exposure in each mannequin orientation must be the same. 5.2.2 The choice of different test duration is partly based on the number of layers in the specimen being tested, some of which serve to absorb the surfactant-treated test liquid and result in attenuating the severity of the liquid challenge to the specimen. 5.3 A nontoxic, non-foaming surfactant is added to water for this test method to simulate liquids of lower surface tensions. Liquids of specific interest can be simulated by treating water to achieve an equivalent surface tension. 5.4 For protective clothing with water-repellent surfaces, the lower surface tension liquid will aid in the evaluation of the construction and configuration of the garment because it is not repelled but wets the protective clothing. This is especially useful for reusable garments whose water-repellent surface interferes with the evaluation of their construction and configuration when new, but is diminished after wearing and washing. 5.5 Fluorescent or colored dyes may be added to the water to enhance detection of liquid penetration into the protective clothing or protective ensemble. 5.6 This test method can be used by both manufacturers and end users to assess liquid penetration resistance. Manufacturers can use this test method to evaluate quality of construction and effectiveness of clothing and ensemble configurations. 5.7 The clothing or ensemble shall be sized to fit the mannequin. It is important that the clothing fit the mannequin well since detection of liquid penetration requires as much contact as possible between the clothing or ensemble and the inner liquid-absorptive garment. 5.8 Results on a mismatched size of clothing or ensemble shall not be used to generalize about a particular construction or configuration. Mannequin fit potentially affects liquid penetration resistance determinations. 5.9 There is no known limit to the kind of protective clothing or protective ensembles that can be evaluated with this test method. 5.10 In some cases protective clothing or protective ensembles that show no liquid penetration during this test method will still fail to protect wearers against specific chemicals due to the material degradation, penetration, or permeation or the toxicity associated with the vapor of liquid chemicals. 5.11 In some cases protective clothing or ......

Standard Test Method for Liquid Penetration Resistance of Protective Clothing or Protective Ensembles Under a Shower Spray While on a Mannequin

EN ISO 17249:2013 耐链锯锯割的防护鞋

Diese Internationale Norm legt Anforderungen an Sicherheitsschuhe mit Schutzwirkung gegen Kettensagenschnitte fest.

Safety footwear with resistance to chain saw cutting

EN 374-4:2013 耐化学品和微生物的防护手套.第4部分:耐化学品渗透性的测定

This European Standard specifies the test method for the determination of the resistance of protective glove materials to degradation by dangerous chemicals with continuous contact. NOTE Annex A gives information on interlaboratory test results on this method. Other tests used to evaluate chemical resistance such as permeation resistance and penetration resistance may not provide sufficient information on the physical property changes affecting a glove during exposure to a chemical. It is necessary that the outside surface of the glove be exposed to the chemical.

Protective gloves against chemicals and micro-organisms - Part 4: Determination of resistance to degradation by chemicals

ASTM F1446-13 评估防护帽性能特征的设备和程序的标准试验方法

5.1 The purpose of these test methods is to provide reliable and repeatable tests for the evaluation of various types of protective headgear. Use of these test methods in conjunction with the specific individual performance standards is intended to reduce the likelihood of serious injury and death resulting from impacts to the head sustained by individuals participating in sports, recreation, and other leisure activities in which protective headgear is worn. 1.1 These test methods cover laboratory equipment, procedures, and basic requirements pertinent to testing protective headgear. Deviations or additions, or both, to these test methods will be specified, as required, in individual ASTM performance standards. 1.2 Requirements—The protective headgear is to be tested under specified environmental conditions for the following: 1.2.1 Impact attenuation (the limiting of head acceleration) of the protective headgear, and 1.2.2 Strength and stability of the retention system and its attachment to the protective headgear. 1.2.3 Special tests for particular protective headgear uses will be specified in the individual performance standards to be used in conjunction with these test methods. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Test Methods for Equipment and Procedures Used in Evaluating the Performance Characteristics of Protective Headgear

ASTM F1818-13 链锯使用者防护鞋的标准规范

1.1 This specification covers minimum requirements for the design, performance, testing, and certification of footwear and foot protective devices designed to provide cut resistance protection to the feet of operators of power chain saws. 1.2 The objective of this specification is to prescribe fit, function, and performance criteria for footwear and foot protective devices, worn by chain saw operators, which are intended to reduce foot injuries caused by contact with a running power saw chain. 1.3 This specification is not intended to serve as a detailed manufacturing or purchasing specification, but can be referenced in purchase contracts to ensure that minimum performance requirements are met. 1.4 Controlled laboratory tests used to determine compliance with the performance requirements of this specification shall not be deemed as establishing performance levels for all situations to which chain saw operators may be exposed. 1.5 Mandatory requirements are indicated by the use of the word shall; recommendations and advisory information is indicated by the use of the word should.

Standard Specification for Foot Protection for Chain Saw Users

ASTM F1414-13 测量矮身材者 (短腿) 穿防护服装耐链锯切割性的标准试验方法

5.1 The purpose of this test method is to provide a measurable criterion of performance about the level of cut resistance provided by different types of protective garments and protected coverings worn by chain saw operators. 5.2 This test method is intended to show to what level a protective garment can offer resistance to the cutting action of a chain saw. 5.3 The protection which can be demonstrated by the garments and coverings tested in accordance with this test method is achieved by: (1) the cut resistance of the material to cutting when put in contact with saw chain; (2) pulling a part of the material or yarns in the material so that they are drawn into the chain and drive mechanism to block the chain movement; (3) the fibers of the materials used to demonstrate both high resistance to cutting and the capacity to absorb rotational energy, so that chain speed can be slowed down sufficiently to stop the movement of the saw chain; or (4) any combination of these. 5.4 This test method does not purport to evaluate comfort of lower body protective garments. 5.5 In case of a dispute arising from differences in reported test results when using this test method for acceptance testing of commercial shipments, the purchaser and the supplier should perform comparative tests to determine if there is a statistical bias between their laboratories. Competent statistical assistance is recommended for the investigation of bias. As a minimum, the two parties should take a group of test specimens from the same lot of components to be evaluated. The test specimens should then be randomly assigned in equal numbers to each laboratory for testing. If a bias is found, either its cause must be determined and corrected or the purchaser and the supplier must agree to interpret future test results in light of the known bias. 1.1 This test method measures cut resistance of garments and devices worn to protect the lower body (legs) when operating a chain saw. 1.2 This test method may be used to test for compliance to minimum performance requirements in established safety standards. 1.2.1 By agreement between the purchaser and the supplier, or as required by established safety standards, it will be decided if this test method will be used to determine one or both of the following: (1) chainspeed 50 (CS50), and (2) success/failure (jamming/chain stop or no cut in less than 1.5 seconds) at specified chain speed. 1.3 This test method may be used to determine levels of protection for areas of coverage as stipulated in established safety standards. 1.4 The values stated in SI units are to be regarded as standard.Note 1???The values stated in each system may not be exact equivalents; therefore, each system must be used independently of the other, without combining values in any way. 1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and ......

Standard Test Method for Measurement of Cut Resistance to Chain Saw in Lower Body (Legs) Protective Clothing

ASTM F1002-13 专供暴露于特种熔融物质和相关热危害的工作人员的使用而制作的防护服及材料的标准性能规范

4.1 This specification provides performance properties for textile material and design characteristics for clothing that represent minimum initial requirements for primary and secondary protective clothing. 4.1.1 The initial performance properties have been selected based on state-of-the-art materials in use and have been compared with commercial standards which take into consideration durability in use for specific apparel items. 4.2 Although the specifications for primary protective clothing are written for outer garments, it is recognized that optimum protective performance to severe exposure involves the use of an appropriate system including work clothing underlayers and undergarments. 4.3 It is permissible for one or more of the requirements in Table 1 to be modified upon agreement between the buyer and seller.TABLE 1 Specification Requirements, Woven Fabrics Characteristic Primary Secondary Section Reference Non-Coated Coated Shirt Pants Breaking strength, min, N [lbf] 223 [50] 334 [75] 134 [30] 223 [50]

Standard Performance Specification for Protective Clothing and the Materials from Which It Is Made for Use by Workers Exposed to Specific Molten Substances and Related Thermal Hazards

KS G 7004-2012 自行车安全帽

이 표준은 자전거를 탈 때 사용하며, 탑승자를 머리 부상에서 보호 또는 상해의 정도를 경감

Protective helmets for bicycle users

DB23/T 1496.8-2012 劳动防护用品配备标准 第8部分：电力设备安装、运行、检修及供电人员

Part 8 of Labor Protection Articles Equipping Standards: Electrical Equipment Installation, Operation, Maintenance and Power Supply Personnel