C82 防火技术 标准查询与下载

BS EN 15794:2009 易燃液体爆炸点的测定

This European Standard specifies a test method to determine the explosion points of flammable liquids in air. This European Standard applies to flammable liquids at atmospheric pressure and at temperatures in the range from - 50 °C to 300 °C. This European standard must not be applied to explosives or materials which, under the test conditions, are thermally unstable liquids (e.g. polymerizing/oxidizing materials).

Determination of explosion points of flammable liquids

ISO 16312-1:2010 火灾危险和风险评估用获取火灾气流毒性数据的物理防火模型的有效性评估指南.第1部分:标准

This part of ISO 16312 provides technical criteria and guidance for evaluating physical fire models (i.e. laboratory combustion devices and operating protocols) used in effluent toxicity studies for obtaining data on the effluent from products and materials under fire conditions relevant to life safety[2]. Relevant analytical methods, calculation methods, bioassay procedures and prediction of the toxic effects of fire effluents can be referenced in ISO 19701[3], ISO 19702[4], ISO 19703[5], ISO 19706[6], ISO 13344[7], and ISO 13571.

Guidance for assessing the validity of physical fire models for obtaining fire effluent toxicity data for fire hazard and risk assessment - Part 1: Criteria

ANSI/NFPA 99B-2010 低气压设施标准

1.1.1* This standard shall apply to all hypobaric facilities in which humans will be occupants or are intended to be occupants of the hypobaric chamber. 1.1.2 This standard shall not apply to hypobaric facilities used for animal experimentation if the size of the hypobaric chamber does not allow for human occupancy.

Standard for Hypobaric Facilities

ASTM E2174-10a 安装的挡火物的现场检查的标准实施规程

This practice is intended to provide a standard set of guidelines that are to be followed when conducting and reporting on inspections of installed fire stops. This practice is intended to provide a means to verify compliance of the installed fire stops to the inspection documents. This practice is not intended to provide a basis for selecting installers or products or both. This practice is not intended to establish any performance criteria of the inspected fire stops.1.1 This practice covers the establishing of procedures to inspect fire stops, including methods for field verification and inspection. 1.2 This practice addresses all types of fire stops installed through or into fire resistive assemblies. Note 18212;Fire stop is defined in Test Method E814. 1.3 This practice provides methods by which qualified inspectors verify that required fire stops on a project have been installed and that their installations are in accordance with the inspection documents. 1.4 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. 1.6 The text of this standard references notes and footnotes that provide explanatory material. These notes and footnotes (excluding those in tables and figures) shall not be considered as requirements of the standard.

Standard Practice for On-Site Inspection of Installed Fire Stops

ANSI/ASTM E2307:2010 使用中型多层测试仪器测定周边挡火墙系统耐火性的试验方法

Test Method for Determining Fire Resistance of Perimeter Fire Barriers Using Intermediate-Scale, Multi-Story Test Apparatus

ASTM E2393-10a 对已安装的防火连接系统和四周挡火墙进行现场检查的标准实施规程

This practice is intended to provide a standard set of guidelines that are to be followed when conducting and reporting on inspections of installed fire resistive joint systems. This practice is intended to provide a means to verify compliance of the installed fire resistive joint systems to the inspection documents. This practice is not intended to provide a basis for selecting installers or products, or both. This practice is not intended to establish any performance criteria of the inspected fire resistive joint systems.1.1 This practice covers the establishment of procedures to inspect fire resistive joint systems, including methods for field verification and inspection. 1.2 This practice addresses all types of fire resistive joint systems and of perimeter joint protection. Note 18212;Fire resistive joint system and joint are defined in Test Method E1966 and UL 2079. Note 28212;Perimeter joint protection is defined in Test Method E2307. Note 38212;Fire resistive joint systems include joints between two fire resistive assemblies, and perimeter joints between a fire resistive floor assembly and a non-fire-resistive wall assembly. The application of these systems are sometimes extended based on an evaluation to other types of construction. 1.3 This practice provides methods by which qualified inspectors verify that required fire resistive joint systems on a project have been installed and that their installations are in accordance with the inspection documents. 1.4 The values stated in inch-pound units are to be regarded as standard. No other units of measurement are included in this standard. 1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. 1.6 The text of this standard references notes and footnotes which provide explanatory material. These notes and footnotes (excluding those in tables and figures) shall not be considered as requirements of the standard.

Standard Practice for On-Site Inspection of Installed Fire Resistive Joint Systems and Perimeter Fire Barriers

ANSI/NFPA 422-2010 飞机事故/意外响应评估用指南

This guide provides a framework for the collection of data that provide information on the effectiveness of aircraft accident/incident emergency response services.

Guide for Aircraft Accident/Incident Response Assessment

ASTM E814-10 贯通处挡火系统火灾试验的标准试验方法

This test method is used to determine the performance of a firestop system with respect to exposure to a standard time-temperature fire test and a hose stream test. The performance of a firestop system is dependent upon the specific assembly of materials tested including the number, type, and size of penetrations and the floors or walls in which it is installed. Two ratings are established for each firestop system. An F rating is based upon flame occurrence on the unexposed surface, while the T rating is based upon the temperature rise as well as flame occurrence on the unexposed side of the firestop system. These ratings, together with detailed performance data such as the location of through-openings and temperatures of penetrating items are intended to be one factor in assessing performance of firestop systems.1.1 This test method is applicable to firestop systems of various materials and construction. Firestop systems are intended for use in openings in fire-resistive walls and floors that are evaluated in accordance with Test Methods E119. 1.2 Tests conducted in conformance with this test method record firestop system performance during the test exposure; but such tests shall not be construed to determine suitability of the firestop system for use after test exposure. 1.3 This test method also measures the resistance of firestop systems to an external force stimulated by a hose stream. However, this test method shall not be construed as determining the performance of the firestop system during actual fire conditions when subjected to forces such as failure of cable support systems and falling debris. 1.4 The intent of this test method is to develop data to assist others in determining the suitability of the firestops for use where fire resistance is required. 1.5 This test method does not apply to membrane penetrations of a floor-ceiling assembly or roof-ceiling assembly that are tested as part of the assembly in accordance with Test Methods E119. 1.6 This test method does not apply to membrane penetrations of load-bearing walls. 1.7 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.8 This standard is used to measure and describe the response of materials, products, or assemblies to heat and flame under controlled conditions, but does not by itself incorporate all factors required for fire-hazard or fire-risk assessment of materials, products, or assemblies under actual fire conditions. 1.9 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. 1.10 The text of this standard references notes and footnotes which provide explanatory material. These notes and footnotes (excluding those in tables and figures) shall not be considered requirements of the standard.

Standard Test Method for Fire Tests of Penetration Firestop Systems

ANSI/NFPA 750-2010 水雾防火系统的标准

1.1* Scope. This standard contains the minimum requirements for the design, installation, maintenance, and testing of water mist fire protection systems. This standard does not provide definitive fire performance criteria, nor does it offer specific guidance on how to design a system to control, suppress, or extinguish a fire. Reliance is placed on the procurement and installation of listed water mist equipment or systems that have demonstrated performance in fire tests as part of a listing process.

Standard on Water Mist Fire Protection Systems

ANSI/NFPA 804-2010 先进的轻水反应堆发电站的防火标准

1.1* Scope. This standard applies only to advanced light water reactor electric generating plants and provides minimum fire protection requirements to ensure safe shutdown of the reactor, minimize the release of radioactive materials to the environment, provide safety to life of on-site personnel, limit property damage, and protect continuity of plant operation. The fire protection is based on the principle of defense in depth.

Standard for Fire Protection for Advanced Light Water Reactor Electric Generating Plants

ANSI/NFPA 302-2010 娱乐和商用机动船的防火标准

1.1.1 This standard shall establish minimum requirements for the prevention of fire and explosion, and for life safety in case of fire, on boats specified in Section 1.3. 1.1.2 This standard shall establish minimum requirements for the following: (1) Elimination of ignition sources (2) Ventilation of accommodation spaces, fuel tanks, and machinery spaces (3) Use of combustible materials (4) Fire-extinguishing equipment and fire exits (5) Control of fire-extinguishing agents in machinery spaces

Fire Protection Standard for Pleasure and Commercial Motor Craft

ANSI/ASTM E906:2010 用热电堆法对材料与产品的热和可视烟雾释放率进行试验的方法

Test Method for Heat and Visible Smoke Release Rates for Materials and Products Using a Thermopile Method

KS F ISO 9705:2009 着火试验.室内物品着火实样试验

이 표준에서는 환기가 잘 이루어진 조건에서 출입문이 1개만 있는 소규모 공간에서 화재 시험

Fire tests－Full-scale room test for surface products

ISO/TR 15658:2009 耐火试验.非炉载体大型试验和模拟的设计与实施准则

Fire resistance tests - Guidelines for the design and conduct of non-furnace-based large-scale tests and simulation

GA 839-2009 火灾现场勘验规则

本标准规定了火灾现场勘验的术语和定义及技术要求，提出了火灾现场勘验的程序和方法。 本标准适用于公安机关消防机构对火灾现场的勘验工作。

Rules for fire scene processing

DIN CEN/TS 45545-7:2009 轨道交通.铁路车辆的防火.第7部分:可燃液体和可燃气体安装的防火安全要求,德文版本CEN/TS 45545-7:2009

Railway applications - Fire protection on railway vehicles - Part 7: Fire safety requirements for flammable liquid and flammable gas installations; German version CEN/TS 45545-7:2009

DIN CEN/TS 45545-6:2009 轨道交通.铁路车辆的防火.第6部分:火灾控制和管理系统,德文版本CEN/TS 45545-6:2009

Railway applications - Fire protection on railway vehicles - Part 6: Fire control and management systems; German version CEN/TS 45545-6:2009

DIN CEN/TS 45545-2:2009 轨道交通.铁路车辆的防火.第2部分:材料和构件的防火行为要求,德文版本CEN/TS 45545-2:2009

Railway applications - Fire protection on railway vehicles - Part 2: Requirements for fire behaviour of materials and components; German version CEN/TS 45545-2:2009

DIN CEN/TS 45545-4:2009 轨道交通.铁路车辆的防火.第4部分:铁路车辆设计的防火安全要求,德文版本CEN/TS 45545-4:2009

Railway applications - Fire protection on railway vehicles - Part 4: Fire safety requirements for railway rolling stock design; German version CEN/TS 45545-4:2009

DIN CEN/TS 45545-1:2009 轨道交通.铁路车辆的防火.第1部分:概述,德国版CEN/TS 45545-1:2009

Railway applications - Fire protection on railway vehicles - Part 1: General; German version CEN/TS 45545-1:2009