C83 灭火技术 标准查询与下载

GB 16668-1996 干粉灭火系统部件通用技术条件

本标准规定了干粉灭火系统的干粉罐、瓶头阀、选择阀、燃气发生器、喷嘴、喷枪等部件的性能要求、试验方法及检验规则等。 本标准适用于固定式和半固定式干粉灭火系统（以下简称干粉系统）。

General technical specifications for components of powder extinguishing systems

GB 16669-1996 二氧化碳灭火系统及部件通用技术条件

本标准规定了二氧化碳灭火系统及容器、容器阀、喷嘴、驱动器、选择阀、单向阀、集流管、连接管等部件的性能要求、试验方法及检验规则。 本标准适用于高压形式贮存的二氧化碳灭火系统。

General technical specifications for components of carbon dioxide fire extinguishing systems

GB 14104-1993 卤代烷灭火系统单向阀的性能要求和试验方法

本标准规定了卤代烷灭火系统部件单向阀的性能要求和试验方法。 本标准适用于卤代烷1301或卤代烷1211灭火系统所用的单向阀。

Halon fire extinguishing system performance requirements and test methods for check valves

GB 14103-1993 卤代烷灭火系统选择阀性能要求和试验方法

本标准规定了卤代烷灭火系统选择阀的性能要求和试验方法。 本标准适用于卤代烷1301和卤代烷1211灭火系统选择阀。

Halon fire extinguishing systems performance reguirements and test methods for selector valves

GB 5135-1993 自动喷水灭火系统 洒水喷头的性能要求和试验方法

本标准规定了自动喷水灭火系统洒水喷头的技术要求、试验方法、检验规则和标志、包装、运输、贮存要求。 本标准适用于自动喷水灭火系统直立型、下垂型、普通型、边墙型、吊顶型洒水喷头及干式下垂型洒水喷头。 本标准不适用于自动喷水灭火系统中的水雾喷头、水幕头。

Automatic water-spouting fire extinguishing system--Performance requirements and test methods for sprinklers

GB 14106-1993 卤代烷灭火系统压力表性能要求和试验方法

本标准规定了卤代烷灭火系统压力表（以下简称压力表）的性能要求和试验方法。 本标准适用于卤代烷固定灭火系统用压力表。

Halon fire extinguishing systems Performance requirements and test methods for pressure gauges

GB 14105-1993 卤代烷灭火系统阀驱动器性能要求和试验方法

本标准规定了卤代烷灭火系统阀驱动器的性能要求和试验方法。 本标准适用于卤代烷1301灭火系统和卤代烷1211灭火系统。

Halon fire extinguishing systems performance requirements and test methods for valve actuators

GB 796-1989 卤代烷灭火系统喷嘴性能要求和试验方法

本标准规定了卤代烷灭火系统部件喷嘴的性能要求和试验方法。 本标准适用于卤代烷1301或卤代烷1211灭火系统。

Halon fire extinguishing systems performance requirement and method of test for nozzles

GB 797-1989 自动喷水灭火系统 湿式报警阀的性能要求和试验方法

本标准规定了湿式报警阀、延迟器和水力警铃的性能要求、试验方法及检验规则。 本标准适用于自动喷水灭火系统的湿式报警阀、延迟器和水力警铃。 本标准不适用于湿式报警阀、延迟器和水力警铃以外的其他附件。

Automatic sprinkler systems performance requirements and methods of test for wet system alarm valves

GB/T 803-1989 空气中可燃气体爆炸指数的测定

本标准规定了在密闭容器内，可燃气体/空气混合气爆炸指数的测定方法，并给出用其他方法测定爆炸指数时应遵循的准则。 本标准只适用于测定有限空间内可燃气体/空气混合气被点燃后的爆炸指数，并不适用于点燃混合气所必须的其他指数。如果按照本标准的实验操作没有点燃可燃气体/空气混合气，不能认为该混合气不会爆炸，应根据具体情况由有关专家予以解释。

Determination of explosion indices of combustible gases in air

GB 795-1989 卤代烷灭火系统容器阀性能要求和试验方法

本标准规定了卤代烷灭火系统部件容器阀的性能要求和试验方法。 本标准适用于卤代烷1301和卤代烷1211灭火系统。

Halon fire extinguishing systems performance requirements and method of test for container valves

DB63/T 2191-2023 森林草原火灾预警监测体系建设规范

Specifications for the construction of forest and grassland fire early warning and monitoring systems

DB5119/T 24-2022 公路隧道火灾扑救行动指南

本文件适用于公路隧道火灾扑救行动的辅助决策和参考依据

Guidelines for Fire Fighting in Highway Tunnels

ISO 21927-3:2021 烟和热控制系统. 第3部分: 烟和热的动力排放通风机规范

This document specifies the product characteristics for powered smoke and heat control ventilators (fans) intended to be used as part of a powered smoke and heat control ventilation system in construction works. It provides test and assessment methods of the characteristics and the conformance criteria of the test assessment results. This document applies to the following: a) fans for smoke and heat control ventilation; b) impulse/jet fans for smoke and heat control ventilation.

Smoke and heat control systems - Part 3: Specifications for powered smoke and heat exhaust ventilators

BS EN 1568-2:2018 灭火介质 泡沫浓缩 用于与水不混溶液体表面应用的高膨胀泡沫浓缩物规范

Fire extinguishing media. Foam concentrates. Specification for high expansion foam concentrates for surface application to water-immiscible liquids

BS EN 1568-4:2018 灭火介质 泡沫浓缩 用于水混溶液体表面应用的低膨胀泡沫浓缩物规范

Fire extinguishing media. Foam concentrates. Specification for low expansion foam concentrates for surface application to water-miscible liquids

ISO 21927-8:2017 烟和热控制系统. 第8部分: 排烟阀

This document applies to smoke control dampers, placed on the market and intended to operate as part of a pressure differential system or smoke and heat control system. This document specifies requirements and gives reference to the test methods defined for smoke control dampers and their associated components, such as actuators which are intended to be installed in such systems in buildings. Furthermore, provision on marking and information on installation and maintenance of these products are also given. This document distinguishes between two categories of smoke control dampers, i.e. single-compartment smoke control dampers and multi-compartment fire-resisting smoke control dampers. Smoke control dampers covered by this document can be installed into smoke control system ducts or onto the ducts’ surface. They can be installed also into a wall, floor or ceiling/roof elements or onto the surface of these elements. To avoid duplication, reference is made to a variety of other standards. To this end, this document NOTE can be read in conjunction with EN 13501-4, EN 1366-10 and ISO 10294-1 for details of the furnace testing. This document does not consider in detail the detrimental and/or corrosive effects that can be caused by process chemicals present in the atmosphere, which are drawn through the system intentionally or inadvertently.

Smoke and heat control systems - Part 8: Smoke control dampers

ISO 21927-7:2017 烟和热控制系统. 第7部分: 烟道节段

This document applies to smoke control duct sections placed on the market and intended to operate as part of a pressure differential system or smoke and heat exhaust system. This document specifies requirements and gives reference to the test methods defined for smoke control duct sections and their associated components (for example, hangers and other items proven at the time of testing), which are intended to be installed in such systems in buildings. Furthermore, marking and information on installation and maintenance of these products are also given in this document. NOTE To avoid duplication, reference is made to a variety of other standards. To this end, this document can be read in conjunction with EN 1366-8, EN 1366-9 and ISO 6944-1, for details of the fire resistance testing and EN 13501-4 for corresponding classification. This document has not considered in detail the detrimental and/or corrosive effects that may be caused by process chemicals present in the atmosphere, which are drawn through the system intentionally or inadvertently. This document also governs associated components used together with smoke control duct sections such as turning vanes and silencers, with the exception of natural and powered smoke ventilators and smoke control dampers, which are covered by separate standards. Ducts for use other than in smoke and heat exhaust/control systems are not covered by this document.

Smoke and heat control systems - Part 7: Smoke ducts sections

EN 13204:2016 消防和救生服务用双动液压救生工具-安全和性能要求

This European Standard specifies safety and performance requirements for double acting hydraulic rescue tools manufactured after the date of publication. It is applicable to double acting hydraulic rescue tool systems which are intended for use by the firefighting and rescue services, principally for cutting through, spreading or pushing apart the structural parts of road vehicles, ships, trains, aircraft and building structures involved in accidents. They consist of a separate power pack, the tool[s] and the necessary interconnections and intended accessories, as defined in Clause 3 - Terms and definitions. This document deals with all significant hazards, hazardous situations or hazardous events relevant to the machinery, when it is used as intended and under conditions of misuse which are reasonably foreseeable by the manufacturer. NOTE 1 The aim is to assist while extracting the casualties or to create a working space for paramedical services taking the local conditions into account. It is not applicable to additional requirements for: a) operation in severe conditions (e. g. extreme environmental conditions such as: temperatures outside the range -20 °C up to +55 °C, corrosive environment, tropical environment, contaminating environments, strong magnetic fields, potentially explosive atmospheres); b) the risk directly arising from the means provided for the portability, transportability and mobility of double-acting hydraulic rescue tools during periods of their operation. NOTE 2 For the EU/EEA other Directives can be applicable to the equipment in the scope, for example the Electro Magnetic Compatibility Directive.

Double acting hydraulic rescue tools for fire and rescue service use - Safety and performance requirements

GA/T 1289-2016 燃烧训练室技术要求

本标准规定了燃烧训练室的术语与定义、分类与型号、设施构成、技术要求、安全要求、验收、维护与保养等。 本标准适用于新建、扩建和改建燃烧训练室的设计、建设、验收与维护。

Technical requirements for burn room for fire fighting training