E20 石油、天然气综合 标准查询与下载



共找到 194 条与 石油、天然气综合 相关的标准,共 13

이 규격은 최대 정격 압력 1 000 kPa, 자기 센서가 부착되어 있거나 부착되지 않은,

Pneumatic fluid power-Cylinders with detachable mountings, 1000 kPa(10 bar) series, bores from 32∼320 mm- Basic, mountings and accessories dimensions

ICS
23.100.20
CCS
E20
发布
2004-12-31
实施
2004-12-31

This standard specifies the procedures to be used for obtaining, by manual methods, samples of liquid hydrocarbons, tank residues and deposits from fixed tanks, railcars, road vehicles, ships and barges, drums and cans, or from liquids being pumped in pipelines. It is should be applied in combination with ISO 3171.

Petroleum liquids - Manual sampling (ISO 3170:2004); German version EN ISO 3170:2004

ICS
75.080
CCS
E20
发布
2004-06
实施

ISO 20783-2:2003 specifies three test methods to assess the stability of emulsions within the category HFB, as defined in ISO 6743-4. Method A describes a method for the determination of stability during storage at ambient temperature [(20 ± 2) °C] and is applicable to HFB and HFB.LT fluids. Method B describes a method for the determination of stability during storage at medium temperature [(70 ± 2) °C] and is again applicable to HFB and HFB.LT fluids. Method C describes a method for the determination of stability during storage at low temperature [(-10 ± 2) °C] and is applicable only to HFB.LT fluids.

Petroleum and related products - Determination of emulsion stability of fire-resistant fluids - Fluids in category HFB

ICS
75.120
CCS
E20
发布
2004-03-03
实施
2004-03-03

Identical with IP 475-2005.

Methods of test for petroleum and its products. BS 2000-475: Petroleum liquids. Manual sampling

ICS
75.080
CCS
E20
发布
2004-02-25
实施
2004-02-25

This International Standard specifies the manual methods to be used for obtaining samples of liquid or semiliquid hydrocarbons, tank residues and deposits from fixed tanks, railcars, road vehicles, ships and barges, drums and cans, or from liquids being pumped in pipelines. It applies to the sampling of petroleum products, crude oils and intermediate products, which are stored in tanks at or near atmospheric pressure, or transferred by pipelines, and are handled as liquids at temperatures from near ambient up to 200 °C. The sampling procedures specified are not intended for the sampling of special petroleum products which are the subject of other International Standards, such as electrical insulating oils (IEC 60475), liquefied petroleum gases (ISO 4257), liquefied natural gases (ISO 8943) and gaseous natural gases (ISO 10715). This International Standard refers to existing methods of sampling and the type of equipment presently in use. It is, however, not intended that it should exclude the use of new equipment not yet developed for commercial use, provided that such equipment enables samples to be obtained in accordance with the requirements and procedures of this International Standard. NOTE For the purposes of this International Standard, the term “% (m/m)” is used to represent the mass fraction.

Petroleum liquids - Manual sampling

ICS
75.080
CCS
E20
发布
2004-02
实施

1.1 일 반 이 규격은 유체 계량(비고 참조)에 사용되는 펄스 데이터 유선 전송

Petroleum liquids and gases-Fidelity and security of dynamic measurement-Cabled transmission of electric and/or electronic pulsed data

ICS
75.180.30
CCS
E20
发布
2003-10-17
实施
2003-10-17

Identical with IP 306/94.

Methods of test for petroleum and its products - Determination of oxidation stability of straight mineral oil

ICS
75.100
CCS
E20
发布
2002-06-13
实施
2002-06-13

Methods of test for petroleum and its products - Determination of oxidation stability of straight mineral oil

ICS
75.100
CCS
E20
发布
2002-06-13
实施
2002-06-13

Standard test method for determination of nickel, vanadium, and iron in crude oils and residual fuels by inductively coupled plasma (ICP) atomic emission spectrometry

ICS
75.160.01
CCS
E20
发布
2002-05-31
实施
2002-07-01

The water and sediment content of crude oil is significant because it can cause corrosion of equipment and problems in processing. A determination of water and sediment content is required to measure accurately net volumes of actual oil in sales, taxation, exchanges, and custody transfers.1.1 This test method describes the laboratory determination of water and sediment in crude oils by means of the centrifuge procedure. This centrifuge method for determining water and sediment in crude oils is not entirely satisfactory. The amount of water detected is almost always lower than the actual water content. When a highly accurate value is required, the revised procedures for water by distillation, Test Method D 4006 (API MPMS Chapter 10.2) (), and sediment by extraction, Test Method D 473 (API MPMS Chapter 10.1), shall be used. Note 1Test Method D 4006 (API MPMS Chapter 10.2) has been determined to be the preferred and most accurate method for the determination of water.1.2 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only.This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. For specific precautionary statements, see 6.1.

Standard Test Method for Water and Sediment in Crude Oil by the Centrifuge Method (Laboratory Procedure)

ICS
75.040 (Crude petroleum)
CCS
E20
发布
2002
实施

1.1 This test method describes the laboratory determination of water and sediment in crude oils by means of the centrifuge procedure. This centrifuge method for determining water and sediment in crude oils is not entirely satisfactory. The amount of water detected is almost always lower than the actual water content. When a highly accurate value is required, the revised procedures for water by distillation, Test Method D 4006 (API MPMS Chapter 10.2) (Note 1), and sediment by extraction, Test Method D 473 (API MPMS Chapter 10.1), shall be used. Note 18212;Test Method D 4006 (API MPMS Chapter 10.2) has been determined to be the preferred and most accurate method for the determination of water.1.2 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only.1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. For specific precautionary statements, see 6.1.

Standard Test Method for Water and Sediment in Crude Oil by the Centrifuge Method (Laboratory Procedure)

ICS
75.040 (Crude petroleum)
CCS
E20
发布
2002
实施

Liquified petroleum gases.Determination of density.Pressure density bottle method

ICS
CCS
E20
发布
1999-12-08
实施
2000-05-01

本标准规定了油气田建设和生产过程中水介质对钢材腐蚀速率测定的试验方法。 本标准适用于评价水介质对钢材的腐蚀性。

Test method for corrsivity of water

ICS
75.020
CCS
E20
发布
1999-05-17
实施
1999-12-01

本标准规定了石油企业节能产品节能效果的测试与计算方法。 本标准适用于石油企业机械采油、油气集输、注水、原油输送管道等系统应用的节能产品节能效果的测试与计算。

The measuring for energy conservation effect of energy conservation products in petroleum enterprise

ICS
CCS
E20
发布
1999-05-17
实施
1999-12-01

本标准规定了陆上油田新建油气集输、注水、古油污水处理及有关公用工程设计节能技术,包括降低能源消耗和减少油气损耗两个方面。 本标准适用于陆上油田地面工程的新建工程。扩建工程和改建工程可参照执行。

Technical specification for design of engrgy conservation for oil field surface engineering

ICS
CCS
E20
发布
1999-05-17
实施
1999-12-01

本标准规定了原油长输管道工程设计节能的技术要求。 本标准适用于原油长输管道新建和改建、扩建工程。

Specification for energy saving in crude oil pipeline design

ICS
CCS
E20
发布
1999-05-17
实施
1999-12-01

本标准规定了对保温结构表面温度及散热损失的几种测试方法和要求,包括测试组织及准工作、数据处理方法、测试误差、保温效果评价方法及测试报告编制等。 本标准适用于动力、采暖、供热及一般用热工业部门的设备、管道及附件散热损失测试。

Measuring heat loss for equipments and pipes

ICS
CCS
E20
发布
1999-05-17
实施
1999-12-01

本标准规定了石油企业能源综合利用的一般原则和油气田及长输管道主要生产系统能源综合利用的技术条件、评价准则及考核准则,给出了石油企业能源综合利用可行性预测、规划和工程概念设计指南。 本标准适用于陆上油气田及长输管道。

Technical guides for energy source comprehensive utilization in petroleum enterprise

ICS
CCS
E20
发布
1999-03-03
实施
1999-10-01

本标准规定了油气田供配电变压器经济运行、无功补偿、供配电系统经济运行的计算广泛和考核指标。 本标准适用于油气田110(66)kV ,35kV和6(10)kV三级电压系统。其包括以下内容: a)油气田自备电厂升压主变压器; b)35~110kV 主变压器; c)6(10)kV主变压器; d)110(66)kV,35kV,6(10)kV输配电线器; e)6(10)kV 电力电容器。

The economic operation specification of electric power supply and distribution system for oil and gas field

ICS
CCS
E20
发布
1999-03-03
实施
1999-10-01

本标准规定了加热炉热工测试方法及计算方法。 本标准适用于油(气)田、长输管道使用的以液体(或气体)为燃料的加热炉。

Heat test for heating furnace

ICS
CCS
E20
发布
1999-03-03
实施
1999-10-01



Copyright ©2007-2022 ANTPEDIA, All Rights Reserved
京ICP备07018254号 京公网安备1101085018 电信与信息服务业务经营许可证:京ICP证110310号