E36 润滑脂 标准查询与下载

DIN 51821-2:1989 润滑剂的检验.使用 FAG 滚动轴承润滑脂检验机 FE9 试验.第2部分:试验方法 A/1500/6000

This standard establishes the general basis for the testing of greases according to DIN 51818 NGLI classes 1 through 4 on the FAG roller bearing grease testing apparatus FE9.

Testing of lubricants; test using the FAG roller bearing grease testing apparatus FE9; test method A/1500/6000

DIN 51820-1:1989 润滑剂检验.采用红外线光谱测定法对润滑脂的分析.第3部分:拍摄和分析红外线光谱

This standard establishes the basis for the analysis of greases by infrared spectrometry. It is applicable for components as well as for the semi-quantitative and quantitative determination of the concentration of individual components of lubricating greases.

Testing of lubricants; analysis of greases by infrared spectrometry; taking and evaluating an infrared spectrum

ASTM D2835-89(2017) 混凝土铺面用预成型压缩密封安装润滑剂的标准规格

1.1 This specification covers a lubricant suitable for facilitating the insertion and positioning of preformed elastomeric compression seals in prepared voids (usually contraction joints) in concrete pavement. 1.2 The requirements of the lubricant are based on the performance of the lubricant as measured by its solids content, homogeneity, consistency, and drying rate. 1.3 The values stated in inch-pound units are to be regarded as the standard. The metric equivalents of U.S. customary units may be approximate. 1.4 The following precautionary caveat pertains only to the test method portion, Section 7 of this specification. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. 1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Lubricant for Installation of Preformed Compression Seals in Concrete Pavements

ASTM D2835-89(2012) 混凝土铺面用预制压缩密封物安装用润滑剂的标准规格

1.1 This specification covers a lubricant suitable for facilitating the insertion and positioning of preformed elastomeric compression seals in prepared voids (usually contraction joints) in concrete pavement. 1.2 The requirements of the lubricant are based on the performance of the lubricant as measured by its solids content, homogeneity, consistency and drying rate. 1.3 The values stated in inch-pound units are to be regarded as the standard. The metric equivalents of U.S. customary units may be approximate. 1.4 The following precautionary caveat pertains only to the test method portion, Section 7 of this specification. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Specification for Lubricant for Installation of Preformed Compression Seals in Concrete Pavements

DIN 51821-1:1988 润滑剂的检验.使用 FAG 滚动轴承润滑脂检验机 FE9 试验.第1部分:一般工作原则

The standard establishes the general basis for the testing of greases according to DIN 51818 NLGI classes 1 through 4 on the FAG roller bearing grease testing apparatus FE9.

Testing of lubricants; test using the FAG roller bearing grease testing apparatus FE9; general working principles

NAVY MIL-F-8839 A-1988 驱动型润滑配件

This specification is approved for use by all Departments and Agencies of the Department of Defense.

FITTINGS, LUBRICATION, DRIVE TYPE

ISO 6743-9:1987 润滑剂、工业润滑油和有关产品(L类) 分类 第9部分:X组(润滑脂)

Lubricants, industrial oils and related products (class L); Classification; Part 9 : Family X (Greases)

NF T60-171:1986 石油产品.低温下润滑脂锥入度的测定

Petroleum products. Determination of cone penetration of greases under low temperature.

DIN 58397-1:1983 精密机械和光学仪器用润滑脂的检验.汽化损失

Testing of lubricating greases for precision engineering and optical instruments; evaporation loss

Testing of lubricating greases for precision engineering and optical instruments; evaporation loss

DIN 58397-2:1983 精密机械和光学仪器用润滑脂的检验.涂铺

Testing of lubricating greases for precision engineering and optical instruments; spreading

Testing of lubricating greases for precision engineering and optical instruments; spreading

GOST 4.23-1983 质量评价系统.塑料润滑脂.质量特性的术语

Настоящий стандарт распространяется на пластичные смазки и устанавливает номенклатуру показателей качества смазок. Показатели пластичн

Quality ratings system. Plastic greases. Quality characteristics nomenclature

ASTM F119-82(2008) 软质密封材料润滑脂渗透率的标准试验方法

This test method is valuable in the development and selection of flexible barrier materials suited for use as grease barriers. The test is rapid in comparison with other methods because of the extremely small quantity of oil required for detection (about 6 μg). The actual time to failure is a multiple of the values obtained by this test method. When permeation is through an absorbent structure such as kraft paper coated with polyethylene, the failure times will be longer and variable, depending on the variation in porosity and thickness of the structure.1.1 This test method provides standard conditions for determining the rate of grease penetration of flexible barrier materials. Pinholes, which can be measured by a separate test, will increase the rate of grease penetration as determined by this test method. 1.2 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only. 1.3 This standard does not purport to address the safety concerns associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Test Method for Rate of Grease Penetration of Flexible Barrier Materials (Rapid Method)

DIN 51818:1981 润滑剂.润滑脂稠度分类.NLGI等级

Lubricants; consistency classification of lubricating greases; NLGI grades Lubrifiants; classification des graisses lubrifiantes d'après leur consistance; classes N LGIZusammenhang mit der vom National Lubricating Grease Institute (NLGI) herausgegebenen

Lubricants; consistency classification of lubricating greases; NLGI grades

DIN 51815-1:1981 润滑剂检验.润滑脂中锂.钠.钙含量的测定.原子吸收光谱法

Testing of lubricants; determination of the content of lithium, sodium and calcium of greases; determination by atomic absorption spectroscopy Essais des lubrifiants; dosage du lithium, du sodium et du calcium des graisses lubrifiantes; détermination spec

Testing of lubricants; determination of the content of lithium, sodium and calcium of greases; determination by atomic absorption spectroscopy

DIN 51814:1981 润滑剂检验.润滑脂中矿物油百分含量和皂质成份的测定.渗析法

Testing of lubricants; determination of mineral oil fraction and soap of lubricating greases; dialysis methodEssais des lubrifiants; détermination de la teneur en huile minérale et en savon des graisses lubrifiantes; méthodede dialyse

Testing of lubricants; determination of mineral oil fraction and soap of lubricating greases; dialysis method

DIN 51807-1:1979 润滑剂检验.在有水的情况下润滑脂性能的测定.静态检验

Testing of lubricants; test on the behavior of greases in the presence of water; static testEssais des lubrifiants; essai du comportement des graisses en présence d'eau; essai statique

Testing of lubricants; Test of the behaviour of lubricating greases in the presence of water; Static test

DIN 58396-2:1977 光学仪器用润滑脂.第2部分:最低要求

Greases for optical instruments; minimum requirements

Greases for optical instruments; minimum requirements

DIN 51805:1974 润滑剂试验.润滑脂流动压力的测定.耐蚀试验（Ｋesternich ）法

Testing of lubricants; determination of flow pressure of lubricating greases; Kesternich methodEssai des lubrifiants; détermination de la pression d'écoulement des graisses lubrifiantes; méthode d'après Kesternich

Testing of lubricants; determination of flow pressure of lubricating greases, Kesternich method

BS SP 21:1950 航空用润滑脂嘴规范

This British Standard deals with a miniature lubricating nipple for aircraft use.

Specification for lubricating nipples for aircraft purposes

HB 5221-1982 －６０～１８０℃中轻负荷航空用润滑脂

本标准适用于在温度为－60～180℃，中、轻负荷条件下工作的各种航空机载电机、电器、仪表、电动机构等使用的润滑油。润滑脂由低分子脂肪酸的锂皂、硅油及添加剂组成。

-60~180℃ Lubricating grease for medium and light load aviation