E38 绝缘油 标准查询与下载

prEN 61125-1991 IEC草案1125.新鲜烃基绝缘油氧化稳定性评定的试验方法

Draft IEC 1125; test methods for evaluating the oxidation stability of unused hydrocarbon-based insulating liquids

SH 0040-1991 超高压变压器油

Extra-high voltage transformer oil

IEC 61065:1991 老化后矿物绝缘油低温流动性的评定方法

Describes the test method, the apparatus and auxiliary materials, the preparations, the test procedure, the measurements, the interpretation of results and the content of the test report.

Method for evaluating the low temperature flow properties of mineral insulating oils after ageing

IEEE Std C57.106-1991 设备用绝缘油的验收和维护指南

Guide for acceptance and maintenance of insulating oil in equipment

NF C27-234:1990 电工技术用流体.用填密柱气相色谱法测定绝缘矿物油中聚氯联二苯含量

Determination of polychlorinated biphenyle (pcbs) in mineral insulating oils by packed column gas chromatography (gc).

NF C27-222:1990 电气设备中绝缘矿物油的监控和维护指南

Supervision and maintenance guide for mineral insulating oils in electrical equipment.

ASTM D2945-90(2003)e2 绝缘油的气体含量的标准试验方法

In filling electrical apparatus, it is desirable to use low gas content transformer oil in order to prevent foaming and to avoid air pockets that might result in gaseous ionization. This procedure provides a simple method to measure the gas content of the oil, and may be used as a factory-control test and as a control or functional test in installation and maintenance work by utilities.1.1 This test method covers the determination of the gas content of electrical insulating oils of low and medium viscosities in the general range of 100 SUS and below at 100°F (37.8°C), and is suitable for field or laboratory use. Note 18212;For testing insulating oils with viscosities above 100 SUS, see Test Method D 831. For individual gas concentrations, see Method D 3612. 1.2 Warning—Mercury has been designated by EPA and many state agencies as a hazardous material that can cause central nervous system, kidney, and liver damage. Mercury, or its vapor, may be hazardous to health and corrosive to materials. Caution should be taken when handling mercury and mercury-containing products. See the applicable product Material Safety Data Sheet (MSDS) for details and EPA’s website (http://www.epa.gov/mercury/faq.htm) for additional information. Users should be aware that selling mercury or mercury-containing products, or both, in your state may be prohibited by state law. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Test Method for Gas Content of Insulating Oils

ASTM D3635-90(1998) 用原子吸收分光光度法测定电绝缘油中溶解的铜含量的标准试验方法

1.1 This test method covers the determination of copper in new or used electrical insulating oil of petroleum origin by atomic absorption spectrophotometry. 1.2 The lowest limit of detectability is primarily dependent upon the method of atomization, but also upon the energy source, the fuel and oxidant, and the degree of electrical expansion of the output signal. The lowest detectable concentration is usually considered to be equal to twice the maximum variation of the background. For flame atomization, the lower limit of detectability is generally in the order of 0.1 ppm. For non-flame atomization, the lower limit of detectability is less than 0.01 ppm. 1.3 The values stated in acceptable metric units are to be regarded as the standard. 1.4 This standard does not purport to address all of the safety problems, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. See 5.4 for specific precautionary statements.

Standard Test Method for Dissolved Copper In Electrical Insulating Oil By Atomic Absorption Spectrophotometry

ASTM D2945-90(2003) 绝缘油的气体含量的试验方法

1.1 This test method covers the determination of the gas content of electrical insulating oils of low and medium viscosities in the general range of 100 SUS and below at 100176;F (37.8176;C), and is suitable for field or laboratory use. Note 18212;For testing insulating oils with viscosities above 100 SUS, see Test Method D 831. For individual gas concentrations, see Method D 3612.1.2 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Test Method for Gas Content of Insulating Oils

IEC 60422:1989 电气设备中矿物绝缘油的维护和管理指南

Supervision and maintenance guide for mineral insulating oils in electrical equipment

NF C27-218:1988 电工液体 绝缘液体雷电冲击击穿电压的测定方法

Fluids for electrotechnical applications - Methods for determining the lightning breakdown voltage of insulating liquids

ASTM D3487-88(1993) 电气装置中用矿物绝缘油标准规范

1.1 This specification covers new mineral insulating oil of petroleum origin for use as an insulating and cooling medium in new and existing power and distribution electrical apparatus, such as, transformers, regulators, reactors, circuit breakers, switchgear, and attendant equipment. 1.2 This specification is intended to define a mineral insulating oil that is functionally interchangeable and miscible with existing oils, is compatible with existing apparatus and with appropriate field maintenance, and will satisfactorily maintain its functional characteristics in its application in electrical equipment. This specification applies only to new insulating oil as received prior to any processing.

Standard Specification for Mineral Insulating Oil Used in Electrical Apparatus

IEC 60465:1988 充油电缆用的未使用过的绝缘矿物油规范

This standard deals in three sections with unused mineral insulating oils, as delivered, for use in cables with oil duct. Section one contains identification and general delivery requirements, section two the description of test methods and section three

Specification for unused insulating mineral oils for cables with oil ducts

IEC 60296/AMD1:1986 变压器和开关设备用的未使用过的矿物绝缘油规范 修改1

Specification for unused mineral insulating oils for transformers and switchgear

ASTM D116-86(2011) 电绝缘液体电阻率(电阻系数)的标准试验方法

For any given ceramic composition, one or more of the properties covered herein may be of more importance for a given insulating application than the other properties. Thus, it may be appropriate that selected properties be specified for testing these ceramic materials. Pertinent statements of the significance of individual properties may be found in the sections pertaining to such properties.1.1 These test methods outline procedures for testing samples of vitrified ceramic materials that are to be used as electrical insulation. Where specified limits are mentioned herein, they shall not be interpreted as specification limits for completed insulators.

Standard Test Methods for Vitrified Ceramic Materials for Electrical Applications

DIN 51353:1985 绝缘油的检验.对腐蚀性硫的检测.银带检验

The silver strip test established by this standard is used for the determination of corrosive sulphur in electrical insulating oils according to DIN VDE 0370 part 1 and part 2. For the testing a silver strip is immersed for 18 h at a temperature of 100 ?in a sample of the insulating oil to be tested. The discolouring of the surface of the silver strip is an indicating for the amount of sulphur in the oil.

Testing of insulating oils; detection of corrosive sulfur; silber strip test

IEEE 637-1985 绝缘油回收指南和绝缘油使用准则

This guide provides detailed procedures for reclaiming used mineral insulating oils (transformer oils) by chemical and mechanical means to make them suitable for reuse as insulating fluids. It describes reclamation procedures, test methods to evaluate the process and end point of reclamation, and essential properties required for reuse in each class of equipment.

Guide for the Reclamation of Insulating Oil and Criteria for Its Use

ANSI/IEEE 637:1985 绝缘油的回收及其使用标准用指南

Covers mineral insulating oil commonly defined as transformer oil; definition and description of reclaiming procedures; the test methods used to evaluate the progress and end point of the reclamation process, and what criteria recommended for the use of reclaimed oils are considered suitable.

Guide for the Reclamation of Insulating Oil and Criteria for Its Use

BS 6522:1984 绝缘油水饱和百分比测定方法

Describes a method of test, based on the measurement of dew-point, for the determination of percentage water saturation of insulating oil at temperatures up to 60C.

Methods for determination of percentage water saturation of insulating oil

ASTM D2296-84(1995)e1 电容器用电绝缘聚丁烯润滑油的质量的连续性的标准规范

1.1 This specification provides the limits within which the properties of electrical insulating polybutene oil for capacitors shall conform in order to ensure an unvarying continuity in the quality and grade of polybutene oil supplied.1.2 It is expected that additional laboratory or service tests of the purchaser's own choosing may be applied to polybutene oil from each source of supply before approval for use.

Standard Specification for Continuity of Quality of Electrical Insulating Polybutene Oil for Capacitors